Boss Audio Systems AR1200.2 User Manual page 5

General precautions
Before installing and using your
!9.�
new amplifier, p/ease Ье­
соте familiar with а// the infor­
mation contained in this manual.
Please keep this manual in а safe
р/асе for future reference.
• Do not open or attempt to repair
this unit yourself. Dangerous high
voltages are present which may result
in electric shock. Refer any repairs to
а qualified service technician.
• То avoid risk of electronic shock or
damage to the amplifier, do not permit
any of this equipment to become
damp or wet from water or drinks. lf
this does occur, immediately unplug
the power wires and send the amplifier
to your local dealer or service center
as soon as possiЫe.
• lf there is smoke or any peculiar
odor present during use or if there is
damage to any of the component
enclosures, immediately unplug the
power wire and send the amplifier to
your local dealer or service center as
soon as possiЫe .
lnstallation precautions
Before you drill or cut any holes,
investigate your car's layout very
carefully. Take special саге when you
work near the gas tank, fuel lines,
hydraulic lines and electrical wiring.
Never operate the amplifier when it is
unmounted. Attach all audio system
components securely to prevent
damage, especially in an accident.
ARMOR MOSFET Amplifier User"s Manual - page 4
Before making or breaking power
connections in your system,
disconnect the vehicle battery. Confirm
that your head unit or other equipment
is turned off while connecting the input
jacks and speaker terminals.
lf you need to replace the power fuse,
replace it only with а fuse identical to
that supplied with the amplifier. Using
а fuse of а different type or rating may
result in damage to your audio system
or your amplifier which is not covered
Ьу the manufacturer's warranty.
Mounting the amplifier
1. Find а suitaЫe location in the vehicle
in which to mount the amplifier.
2. Make sure there is sufficient air
circulation around the intended
mounting location.
3. Mark the location for the mounting
hole screws Ьу positioning the amplifier
where you wish to install it. Use а
scribe or mounting screw, inserted
through each of the amp's mounting
holes, to mark the mounting surface.
lf the mounting surface is carpeted,
measure the hole centers and mark
with а felt tip реп.
4. Drill pilot holes in the mounting
surface for the mounting screws. Place
the amplifier in position, and attach
the amplifier to the mounting surface
securely using screws.
SHOCK HAZARDI Do not open the case
of this product. There are dangerous
voltages present within the unit. Тhere are
по user-serviceaЫe parts within the unit.
Power and Speaker Wiring
4 Channel and Bridged Modes
tt' t- - ---- -
СН2
Speaker
Four
Channel
Mode
@
@
SPEAKER
IMPEDANCE
2-80HMS
SPEAKER
IMPEDANCE
4-80HMS
LEFТ
Subwoofer
Bridged
Mode
SPEAКER
IMPEDANCE
4-ЗОНМS
RIGHT
Subwoofer
Connect the Negative (-) Connect the Positive (+)
terminal of the RIGHT terminal of the RIGHT
subwoofer to the СН4 (-) subwoofer to the СНЗ (+)
amplifier terminal. amplifier terminal.
4-Channel Amplifiers
AR1600.4 and AR2400.4
SPEAKER
IMPEDANCE
онмs
2·8
@
_Chassls
-:- ground
point
to REMOTE TURN-ON
terminal of head unit
Connect the Negative (-) terminal of the LEFТ subwoofer to
the СН2 (-) amplifier terminal.
Connect the Positive (+) terminal of the LEFТ subwoofer to
the СН1 (+) amplifier terminal.
_Chassis
-:- ground
point
to REMOTE TURN-ON
terminal of head unit
ARMOR MOSFET Amplifier User"s Manual - page 11