Table of Contents
Advertisement
Quick Links
C
V
SX60
OMPACT
IEW
U
M
SER
ANUAL
2006 3D perception AS All rights reserved.
The copyright of this document is the property of 3D perception AS. The document is supplied on the
express terms that it is to be treated as confidential. No part of this document may be reproduced or
transmitted in any form or by any means, electronic or mechanical for any purpose, without the
express written permission of 3D perception AS. The information in this document is subject to
change without notice and is provided 'AS IS'.
Advertisement
Table of Contents
Related Manuals for 3D Perception COMPACTVIEW SX60
Summary of Contents for 3D Perception COMPACTVIEW SX60
- Page 1 2006 3D perception AS All rights reserved. The copyright of this document is the property of 3D perception AS. The document is supplied on the express terms that it is to be treated as confidential. No part of this document may be reproduced or transmitted in any form or by any means, electronic or mechanical for any purpose, without the express written permission of 3D perception AS.
- Page 2 3D perception SX60 OMPACT Revision 2 User Manual OCUMENT TATUS Revision Month Year Paragraph(s) Prepared by Description of Change August 2006 A F Rotheram Initial release October 2007 A F Rotheram Remove RS232 February 2008 None D Kennedy Remove HA...
-
Page 3: Table Of Contents
3D perception SX60 OMPACT Revision 2 User Manual ABLE OF ONTENTS ........................1 NTRODUCTION .....................2 AFETY AND ARNINGS Safety ........................2 Warning........................2 Potential Health Issues Related to Mercury Vapour...........3 Recycling Warning ....................4 Remote Control Warning ..................4 Warning Symbols .....................4 .........................6 PTICAL ENSES .......................8... - Page 4 3D perception SX60 OMPACT Revision 2 User Manual 13.2 Ceiling Mount Cover ....................23 14. U ...................... 24 SING THE ROJECTOR 15. M ........................25 YSTEM 15.1 Top Menu ....................... 25 15.2 Picture Sub Menu ....................26 15.3 Dynamic Sub Menu ....................27 15.4...
- Page 5 3D perception SX60 OMPACT Revision 2 User Manual 22.1 FCC........................47 22.2 EN 55022 Warning ....................47 22.3 Canada........................47 23. L , ‘FCC S ’ ‘T ’....... 48 IMITED ARRANTY TATEMENT RADEMARKS OPYRIGHT 24. C ........................50 ONTACT US...
-
Page 6: Introduction
User Manual NTRODUCTION The CompactView SX60 digital projector is designed with the latest state-of-the-art technologies in illumination, imaging, optics, electronics, thermal and industrial design in order to serve traditional as well as novel imaging applications across a variety of markets, offering features such as: •... -
Page 7: Safety And Warnings
Revision 2 User Manual AFETY AND ARNINGS The CompactView SX60 user guide contains important information about safety precautions and the set-up and use of the projector. Please read the manual carefully before you operate the projector. Safety The CompactView SX60 complies with relevant safety regulations for data processing equipment for use in an office environment. -
Page 8: Potential Health Issues Related To Mercury Vapour
3D perception SX60 OMPACT Revision 2 User Manual Always allow ample airflow through the projector. Never block any of the air vents. Never cover the unit in any way while running. Allow for sufficient distance to walls and ceilings to avoid overheating. -
Page 9: Recycling Warning
3D perception SX60 OMPACT Revision 2 User Manual airway irritation, tightness in the chest, a burning sensation in the lungs, coughing, nausea, vomiting and diarrhea. Children and fetuses are particularly sensitive to the harmful effects of metallic mercury to the nervous system. - Page 10 3D perception SX60 OMPACT Revision 2 User Manual RECYCLE Warning! Recycle properly, do not dispose of in ordinary waste! NO TELEPHONE Warning! Do not connect to telephone lines!
-
Page 11: Optical Lenses
3D perception SX60 OMPACT Revision 2 User Manual PTICAL ENSES A range of fixed and zoom lenses is available to cover most applications, for both front and rear projection. The lenses are powered and fitted with a bayonet-mount for ease of installation. - Page 12 3D perception SX60 OMPACT Revision 2 User Manual Remove the lens cap from the projection lens. If you switch the projector on with the lens cap in place, the lens cap may melt, damaging not only the lens cap, but also the projection lens...
-
Page 13: Projector Overview
3D perception SX60 OMPACT Revision 2 User Manual ROJECTOR VERVIEW Lens A IR sensor B Ventilation C Lens release D Power connector E Keypad F Connector panel G LCD H Lamp lids I Adjustable feet J Security lock K Ceiling mount L... -
Page 14: Keypad
3D perception SX60 OMPACT Revision 2 User Manual EYPAD The keypad is illuminated for operation in dark environments. Available functions are illuminated in yellow while selected (active) functions are illuminated in green. Functions that are not available are not illuminated. - Page 15 3D perception SX60 OMPACT Revision 2 User Manual Select the VGA input as active source. Activate the DVI-D input. Select BNC as source. YPbPr Activate the component video input. S-VIDEO Select super video as active source. C-VIDEO Activate the composite video input.
-
Page 16: Indicators
3D perception SX60 OMPACT Revision 2 User Manual NDICATORS STATUS Indicates the overall system status by green, yellow and red colours. PERMANENT GREEN LIGHT The projector is turned on and in normal operation. PERMANENT YELLOW LIGHT The unit is in standby mode; no source(s) connected, or the source(s) connected are inactive or switched off, thereby activating the power-save function (DPMS). - Page 17 3D perception SX60 OMPACT Revision 2 User Manual PERMANENT RED LIGHT Lamp life has expired or lamp is not igniting or lamp door is open. Please change projection lamp immediately. Failing to change lamp may lead to lamp explosion. NO LIGHT...
-
Page 18: Remote Control
3D perception SX60 OMPACT Revision 2 User Manual EMOTE ONTROL The remote control allows flexible access to the projector settings, either through direct keys, or through the menu system. The remote control is backlit for use in dark environments. It also has a data-jack that allows for wired connection to the projector. - Page 19 3D perception SX60 OMPACT Revision 2 User Manual S-VIDEO Select the super video input as signal source. YPbPr Select component video input. Select the DVI input. Select the VGA input. Select the BNC input. X-PORT 1, 2 Activates the X-PORT 1, 2. These keys are enabled by the X-PORT 1, 2 devices as and when attached.
- Page 20 3D perception SX60 OMPACT Revision 2 User Manual LASER Activate the built-in laser pointer. CAUTION! Do not point laser beam at people. Do not stare into laser beam. Press OK to confirm selected option in menu. GAMMA Press GM+ or GM- to select between gamma settings.
-
Page 21: Connector Panel
3D perception SX60 OMPACT Revision 2 User Manual ONNECTOR ANEL The connector panel may be illuminated by pushing the LIGHT key on the keypad. C-VIDEO: A Used for standard video quality. S-VIDEO: B Used for improved quality video. YPbPr: C Used for high quality video reproduction. - Page 22 3D perception SX60 OMPACT Revision 2 User Manual RC: I Allows connection of external IR receiver or wired remote control. Triggers: J 12VDC for Screen Drop and Aspect Ratio control USB - interface: K Allows for computer mouse control. LAN: L Provides access to control and monitoring over a Local Area Network Mains power connector: M Use only three-prong / grounded power cord.
-
Page 23: Set -U P
3D perception SX60 OMPACT Revision 2 User Manual IDEO NOTE: Before starting set-up, switch off all equipment. Four video sources may be connected, using the YPbPr (component), BNC (RGB), S-VIDEO (super video) and VIDEO (composite video) inputs. Component and RGB video will display more detailed images. Composite video yields images with less detail. -
Page 24: Set-Up Computer
3D perception SX60 OMPACT Revision 2 User Manual OMPUTER NOTE: Before starting set-up, switch off all equipment. The projector may be connected to up to three computer sources simultaneously, using the VGA, BNC and DVI inputs. The VGA and BNC interfaces are analogue and may cause some noise in the projected image, depending on the signal quality from the graphics card in the computer. -
Page 25: Image Adjustments
3D perception SX60 OMPACT Revision 2 User Manual MAGE DJUSTMENTS Various optical adjustments are available, depending on your choice of lens. All lens adjustments are motorized and controlled by the keypad, remote control or by RS232 or LAN. Two kinds of lenses are available; fixed or zoom. A fixed lens has permanent focal length, or throw ratio. -
Page 26: Lamp Operation
3D perception SX60 OMPACT Revision 2 User Manual PERATION The projector is fitted with two individual projection lamps that can be run in various modes. In addition, lamps can be replaced as needed separately. This ensures an optimized cost of ownership. -
Page 27: Ceiling Mount
3D perception SX60 OMPACT Revision 2 User Manual EILING OUNT 13.1 IXING THE EILING OUNT The projector can be ceiling mounted using an approved UL tested/ listed ceiling mount fixture, with a capacity of minimum 60 kg / 130 lbs. -
Page 28: Ceiling Mount Cover
3D perception SX60 OMPACT Revision 2 User Manual 13.2 EILING OUNT OVER The auxiliary cable cover can be mounted on the projector to conceal the interface cables and power cord when the unit is ceiling mounted. Connect all cables and fix them in place before the cable cover is attached to the projector. -
Page 29: Using The Projector
3D perception SX60 OMPACT Revision 2 User Manual SING THE ROJECTOR After Set-up, switch on all equipment. The projector can be controlled by the keypad on the rear, by the remote control or using the RS232 or LAN interfaces. When using the remote control, either all or select individual units may be addressed, see the CONTROL sub menu - RC ID. -
Page 30: Menu System
3D perception SX60 OMPACT Revision 2 User Manual YSTEM The menu system gives access to a multitude of image and system controls. The menu system is structured through a top menu and several sub menus. The sub menus may vary depending on the actual source selected. -
Page 31: Picture Sub Menu
3D perception SX60 OMPACT Revision 2 User Manual 15.2 ICTURE brightness S-Video / C-Video Adjusts the image brightness. A higher setting will increase the brightness; a lower setting will decrease the brightness of the image. contrast Controls the contrast of the image. A higher setting will yield a ‘harder’... -
Page 32: Dynamic Sub Menu
3D perception SX60 OMPACT Revision 2 User Manual 15.3 YNAMIC white boost S-Video / C-Video Increases the white level of the image for enhanced contrast gamma The source image is adapted to characteristics typical to certain applications. This enables an... -
Page 33: Advanced Sub Menu
3D perception SX60 OMPACT Revision 2 User Manual 15.4 DVANCED h position S-Video / C-Video Shifts the image sideways. v position Shifts the image up and down. phase Adjust for stable image. A jittery image may appear with certain VGA sources. You may also... -
Page 34: Set-Up Sub Mneu
3D perception SX60 OMPACT Revision 2 User Manual 15.5 keystone V Adjust vertical keystone correction. Compensates for the geometrical distortion of the projected image resulting from tilting the projector to shoot higher up on the wall. keystone H Adjust horizontal keystone correction. -
Page 35: Utilities Sub Menu
3D perception SX60 OMPACT Revision 2 User Manual 15.6 TILITIES system information Displays information about the source and Utilities projector status. Turn the On Screen Display on (display) or off (hide) during source scan. OSD timeout Defines how long OSD is displayed after last key action before it disappears from the screen. -
Page 36: Control Sub Menu
3D perception SX60 OMPACT Revision 2 User Manual LCD options. Define options for the rear monitor LCD. LCD timeout Select timeout when LCD turns off after use. LCD dim level Select intensity in LCD backlight. calibrate source Allows calibration of projector to analogue Calibrate RGB source. -
Page 37: Lamp Sub Menu
3D perception SX60 OMPACT Revision 2 User Manual 15.8 Mode select dual or single lamp mode. select eco mode (reduced power for longer lamp life). advanced individual lamp control. single select lamp 1 or lamp 2 as active lamp. lamp 1, lamp 2 power select lamp power from 80-100%. -
Page 38: Rs 232 And Lan Control
3D perception SX60 OMPACT Revision 2 User Manual RS 232 LAN C ONTROL 16.1 RS 232 You may control and monitor the projector remotely through the serial RS232 control interface. Two RS232 protocols are employed. A simple instruction set (SIS) ASCII protocol gives access to the most frequently used commands. -
Page 39: Trouble Shooting
3D perception SX60 OMPACT Revision 2 User Manual ROUBLE HOOTING 17.1 MAGE No connection: Check if all connections are properly made. Source off: Check if the equipment is powered on. Lamp dead: The lamp may need replacement. Check the LAMP TIME in the UTILITIES sub menu. -
Page 40: Unsharp Image
3D perception SX60 OMPACT Revision 2 User Manual 17.4 NSHARP MAGE Keystone correction may have been activated inadvertently, compressing parts of the image that affect the display of fine-line graphics, text and other images of high resolution Source resolution is... -
Page 41: Maintenance
3D perception SX60 OMPACT Revision 2 User Manual AINTENANCE The projector may from time to time need cleaning. Never open the unit, as this will void any warranties. Refer service and repair to qualified personnel only. The projector is using lamps that have a limited life time. Please refer to the LAMP CHANGE section below for further details. -
Page 42: Service Information
3D perception SX60 OMPACT Revision 2 User Manual ERVICE NFORMATION This product contains no user serviceable parts. If the product fails to function as expected, please first check that all connections are properly made, and that the power cord is properly connected. -
Page 43: Lamp Change
3D perception SX60 OMPACT Revision 2 User Manual HANGE The LAMP indicators on the keypad will turn red when lamp life expires. Change the lamp when lifetime expires. Always replace lamp with the same type and rating. The lamp includes an electronic lamp timer that is tracking the life time of the lamp. - Page 44 3D perception SX60 OMPACT Revision 2 User Manual Replace with a new lamp in reverse order. Insert a new lamp. E Observe the guide pins. Turn the tree locking screws F a quarter turn clockwise. Close the lamp lid. H Turn the locking screw I clockwise.
-
Page 45: Technical Data
3D perception SX60 OMPACT Revision 2 User Manual ECHNICAL 21.1 ROJECTOR Resolution 1400 x 1050 (native) SXGA+, 4 : 3 aspect ratio Display technology Single chip DLP™ technology by Texas Instruments® DMD™ with DarkChip™ technology Display device UXGA, SXGA+, SXGA, XGA, SVGA, VGA, PC, MAC, SGI and other workstations, RGBHV, RGBS, RGsB Computer Compatibility HDTV (1080i, 720p, 576i/p, 480i/p), NTSC, NTSC 4.43, PAL, PAL-M,... - Page 46 3D perception SX60 OMPACT Revision 2 User Manual Inputs 1 VGA 15 pin female HD-DSUB analogue RGBHV 1 DVI-D female digital RGB 5 BNC male analogue RGBHV 1 Component video female 3 x RCA/phono 1 S-video female 4 pin mini-DIN...
-
Page 47: Lenses
3D perception SX60 OMPACT Revision 2 User Manual 21.2 ENSES Short fixed lens f = 15.32 mm F = 2.1 - 6.5 throw ratio (distance : width) = 0.8 : 1 throw distance = 0.5 - 2.5 m (1.65 - 8,25 ft.) - Page 48 3D perception SX60 OMPACT Revision 2 User Manual...
-
Page 49: Connectors
3D perception SX60 OMPACT Revision 2 User Manual 21.3 ONNECTORS Aspect BNC B BNC G 3.5mm mini jack BNC MALE BNC MALE TIP: 12V DC STEM: BLUE STEM: GREEN 80mA max. SHIELD: GND SHIELD: GND STEM: GND BNC H - C... - Page 50 3D perception SX60 OMPACT Revision 2 User Manual Computer VGA1 G / Y 15 HIGH DENSITY PHONO/RCA FEMALE RJ 45 DSUB FEMALE 1 Analogue R in STEM GREEN: G/Y 1 TX+ 2 Analogue G in SHIELD: GND 2 TX- 3 Analogue B in...
- Page 51 3D perception SX60 OMPACT Revision 2 User Manual RS-232 In RS-232 Out S - Video 9 PIN DSUB FEMALE 9 PIN DSUB MALE 4 PIN MINI DIN FEMALE 1 NC 1 NC 1 GND 2 RXD 2 TXD 2 GND...
-
Page 52: Declarations
3D perception SX60 OMPACT Revision 2 User Manual ECLARATIONS 22.1 This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 53: Limited Warranty , 'Fcc Statement
12-month period from the date of purchase of a C SX60 OMPACT projector. During the warranty period, 3D perception will, at its option and in its sole discretion, repair or replace defective parts, including replacement of the entire C SX60 projector, at no OMPACT additional charge to the Customer. - Page 54 N-1373 Asker Norway In the case of any such claim, inspection shall be promptly arranged with 3D perception or it’s authorised personnel, and where appropriate, representatives of the carrier. Any other claim or action respecting the condition or conformity of a C...
-
Page 55: Ontact Us
+47 66 98 70 70 Fax: +47 66 98 70 71 Support desk: +47 66 98 70 90 info@3d-perception.com support@3d-perception.com www.3d-perception.com Regional offices USA 3D perception Inc 1277 N. Semoran Blvd. Suite 117 Orlando, Florida 32807 Tel: +1 321 235 7999 Fax: +1 321 235 7992 paal.s@3d-perception.com...
Need help?
Do you have a question about the COMPACTVIEW SX60 and is the answer not in the manual?
Questions and answers