Related Manuals for Honeywell HD3VC4SHR
Summary of Contents for Honeywell HD3VC4SHR
- Page 1 3 Inch Dome Camera NTSC / PAL HD3VC4SHR HD3VC4SHRX HD3VC4SA HD3VC4SAX Quick Install Guide Document 900.0510 – 05/06 – Rev 1.00...
- Page 2 Revisions Issue Date Revisions 1.00 05/06 New document. Rev 1.00 Document 900.0510 05/06...
-
Page 3: Explanation Of Graphical Symbols
Warnings Installation and servicing should be performed only by qualified and experienced technicians to conform to all local codes and to maintain your warranty. WARNING! The Use of CSA Certified/UL Listed Class 2 power adapters is required to ensure compliance with electrical safety standards. -
Page 4: Fcc Compliance Statement
FCC Compliance Statement Information to the User: This equipment has been tested and found to comply with the limits for a Class A digital device. Pursuant to Part 15 of the FCC Rules, these limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. -
Page 5: Table Of Contents
Contents Introduction ......... 1 Before You Begin . -
Page 6: Introduction
• One hardware kit • One 2nd video monitor output cable • One mounting template If any parts are missing or damaged, contact the dealer you purchased the camera from or call Honeywell Customer Service. Rev 1.00 Document 900.0510 05/06... -
Page 7: Cautions And Operating Notes
Cautions and Operating Notes Power Supply This dome camera can operate on 24 VAC or 12 VDC. Operating Conditions Avoid: • Viewing bright objects (example, light fixtures) for extended periods. • Operating or storing the unit in the following locations: •... -
Page 8: Installation
Installation The HD3VC4S Series is a fully-integrated enclosure with camera and lens. Figure 1 Camera Parts Legend Conduit hole used for surface run power/video connector Camera housing Dome cover Zoom lever Focus lever Video output connector 24 VAC/12 VDC power input connector Note Figure 5... -
Page 9: Removing The Dome Cover
Removing the Dome Cover Gently turn the dome cover (#5 on Figure 2) counter-clockwise to unlock and pull free of the housing. Remove the inner liner (#4) by gently pulling it free of the two notches (#2) in the housing (#1). Set the dome (and liner) aside. Figure 2 Dome Cover Removal. -
Page 10: Mounting The Camera
Mounting the Camera Place the supplied mounting template (#2 on Figure 3) on the mounting surface and mark the holes. Drill two holes, then insert the screw anchors (#1) into the holes. Secure the camera housing to the wall with the TP4 x 15 mm tapping screws supplied (#3). -
Page 11: Adjusting The Camera Position
Adjusting the Camera Position Figure 4 Camera Position Adjustment Legend Tilt adjustment bracket and thumbnuts (x2) Axis ring Zoom lever Focus lever Loosen the Tilt adjustment thumbnuts (see #1 on Figure 4). Turn one Tilt adjustment thumbnut counter-clockwise and one clockwise. Turn the Tilt adjustment bracket (#1) and Axis ring (#2) in the desired direction, then retighten the thumbnuts. -
Page 12: Optional Camera Settings
Note It is important that you lock the zoom and focus levers after making adjustments. This will avoid the positions moving (for example, from temperature changes or vibrations). Caution Do not turn the lens more than 360° as this may cause the internal cables to twist and disconnect or break. - Page 13 Picture Brightness Use the LEVEL screw (#1) to compensate for the iris level. L (low) makes the picture darker. H (high) makes the picture brighter. Phase Adjustment Use the V Phase Adjustment Pot (#2) to adjust the phase difference between cameras. Make sure Switch 4 is ON to activate the Line lock function (AC operation only).
-
Page 14: Attaching The Dome Cover
Attaching the Dome Cover To attach the dome cover, follow Figure Use a soft, lint-free cloth to wipe the dome cover clean and remove fingerprints. Attach the inner liner (#3) to the Tilt adjustment screw (#2). Push down until it clicks into place. Place the dome (#4) on the unit. -
Page 15: Routine Maintenance
Routine Maintenance • The dome cover is an optical part. Use a soft, dry cloth to remove any fingerprints or dust. • Clean the camera housing with a soft, dry cloth. For more stubborn stains, use a cloth dampened with a small quantity of neutral detergent, then wipe dry. -
Page 16: Warranty And Service
Warranty and Service Subject to the terms and conditions listed on the Product warranty, during the warranty period Honeywell will repair or replace, at its sole option, free of charge, any defective product returned prepaid. In the event you have a problem with any Honeywell product, please call Customer Service for assistance or to request a Return Merchandise Authorization (RMA) number. -
Page 17: Specifications
Specifications Video Signal Specifications NTSC Video Standard: High Res Standard Res High Res Standard Res Scanning System: 525 lines, 2:1 Interlace Image Sensor: 1/3” Interline Transfer CCD Number of Pixels 768 x 494 510 x 492 752 x 582 500 x 582 (H x V): Minimum 0.5 lux @ F1.6... - Page 18 White Balance: Gamma: 0.45 BLC: On/Off, switchable Electrical Specifications Input Voltage: 12 VDC/24 VAC Input Tolerance: ± 15% Power 3.5 W (max) Consumption: Mechanical Dimensions 4.33” x 3.91” (110 mm x 96.3 mm) (WxH): Weight: .66 lb (.3 Kg) Net, 1.32 lb (.6 Kg) Shipping Construction: Housing and dome: Polycarbonate Environmental...
-
Page 19: Cable Guidelines
Calculations are based on an unregulated linear power supply, which would be the worst case. Using a regulated or switching power supply can increase the cable distance. Honeywell recommends using a CSA Certified/UL listed Class 2 power adapter to ensure compliance with electrical safety standards. - Page 20 +1.800.796.CCTV (North America only) © 2006 Honeywell International Inc. All rights reserved. No part of this publication may be reproduced by any means without written permission from Honeywell Video Systems. The information in this publication is believed to be accurate in all respects. However, Honeywell Video Systems cannot assume responsibility for any consequences resulting from the use thereof.