Advertisement
ROLLOVER
5 in 1 cot to full size single bed
This product is covered by a number of registered designs, trademarks and patents pending
!
Two adults required to assemble this cot.
The manufacturer's assembly instructions must be followed
!
in detail to ensure the safety features to the cot are not compromised.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Grotime Rollover
Summary of Contents for Grotime Rollover
- Page 1 ROLLOVER 5 in 1 cot to full size single bed This product is covered by a number of registered designs, trademarks and patents pending Two adults required to assemble this cot. The manufacturer's assembly instructions must be followed in detail to ensure the safety features to the cot are not compromised.
-
Page 2: Parts List
HARDWARE INVENTORY 16mm Bolts 70mm Bolts Guide Pins Wood Screws CAMDOCK Base Plates Allen Key Feet Pads PRE-INSTALLED HARDWARE Oval Badges x 4 pcs with Locking Bolts 40mm Bolts x 8 pcs PARTS LIST 1 x Fixed Side 2 x End Panels 1 x Drop Side 1 x Cot Base 4 x BILATERAIL... - Page 3 STEP 1 ASSEMBLE FIXED SIDE TO ENDS 70mm Bolts Fixed Side End Panels Do not tighten bolts at this stage STEP 2 FIX FOUR CAMDOCK BASE PLATES* 16mm Bolts CAMDOCK Base Plates *Patent pending Chose high or low position for mattress base HIGH Bassinet level Toddler level...
- Page 4 STEP 3 PLUG FINGER ENTRAPMENTS 16mm Bolts STEP 4 PLACE COT BASE ON TOP OF BASE PLATES 1 x Cot Base...
- Page 5 STEP 5 ASSEMBLE COT BASE 16mm Bolts Do not tighten bolts at this stage STEP 6 SCREW FOUR GUIDE PINS INTO ENDS FIRMLY Guide Pins Screw Driver...
- Page 6 STEP 7 ASSEMBLE DROP SIDE Drop Side Align two access holes in the built-in runner with the guide pins on one end. Now repeat on other end. Ensure correct side is facing out. STEP 8 FULLY SCREW IN LOCKING BOLTS Lift drop side up until it clicks into the locking position.
- Page 7 STEP 9 TIGHTEN ALL BOLTS STEP 10 OPERATION To lower drop side, lift from centre of top rail, hold side in that position while using your leg to push inward on centre of bottom rail. Then allow to slide gently down. Base shown in Lower Position.
- Page 8 DAY BED CONVERSION Remove dropside by reversing to step 5. Remove dropside guide pins (HC) from the ends to prevent injury. Day Bed COT BED CONVERSION Remove dropside by reversing to step 5. Cot Bed...
- Page 9 FULL SIZE SINGLE BED CONVERSION Rollover action Patent Pending STEP 1 Disassemble the cot following the assemble instructions in reverse order. Roll over cot ends on their sides STEP 2 REMOVE FOUR GROTIME BADGES...
- Page 10 STEP 3 ASSEMBLE BILATERAIL BED RAILS Patent pending BILATERAIL Base Rails BILATERAIL Base Brackets mm Bolts 20mm Insert Nut Place insert sleeves into base rail. (2 at each end of rail) Align insert sleeve so the slot is facing out STEP 4 Assembled base rails Cot Bed Slats...
- Page 11 STEP 5 Use the four wood screws to x the rails and slats together. Wood Screws Screw Driver Adjust insert nut clockwise/anticlockwise so that threaded holes in insert nut align with bolt holes in end of base rail STEP 6 ASSEMBLE SINGLE BED BASE BETWEEN TWO ENDS 70mm Bolts TIGHTEN ALL BOLTS...
- Page 12 MAINTENANCE Check your cot regularly. Retighten all bolts. For after sales service contact Grotime Service Australia on 1300 799 912; or New Zealand on 0508 476 932; RECOMMENDED MATTRESS SIZE This cot has been manufactured for use with a mattress which measures 760mm in width and 1300mm in length and 130mm in thickness.
Need help?
Do you have a question about the Rollover and is the answer not in the manual?
Questions and answers