Panasonic HDC-SD600P Service Manual page 42

Service Manual
Diagrams and Replacement
Parts List
High Definition Video Camera
Model No.
HDC-SD600P
HDC-SD600EB
HDC-SD600EC
HDC-SD600EE
HDC-SD600EF
HDC-SD600EG
HDC-SD600EP
HDC-SD600GN
Vol. 1
Colour
(K)...........Black Type
(H)...........Glay Type (only EB)
Table of contents
S1. About Indication of The Schematic Diagram ............................ S-1
S1.1. Important Safety Notice......................................................... S-1
S2. Voltage Chart ........................................................................... S-2
S2.1. Strobe P.C.B. ......................................................................... S-2
S2.2. BATT_Catcher P.C.B. ............................................................ S-2
S2.3. Front P.C.B. ........................................................................... S-2
S2.4. MIC AMP P.C.B. .................................................................... S-2
S3. Block Diagram .......................................................................... S-3
S3.1. Overall Block Diagram .......................................................... S-3
S4. Schematic Diagram .................................................................. S-4
S4.1. Interconnection Diagram ....................................................... S-4
S4.2. Strobe Schematic Diagram ................................................... S-5
S4.3. BATT_Catcher Schematic Diagram ...................................... S-6
S4.4. Front Schematic Diagram ..................................................... S-7
S4.5. MIC AMP Schematic Diagram ............................................... S-8
S4.6. Side R Schematic Diagram ................................................... S-9
S4.7. SS SW Schematic Diagram .................................................. S-9
VM1005029CE
S1. About Indication of The Schematic Diagram
S1.1. Important Safety Notice
COMPONENTS IDENTIFIED WITH THE MARK
FOR SAFETY. WHEN REPLACING ANY OF THESE COMPONENTS USE ONLY THE SAME TYPE.
1.Although reference number of the parts is indicated on the P.C.B. drawing and/or
schematic diagrams, it is NOT mounted on the P.C.B. when it is displayed with "$" mark.
2.It is only the "Test Round" and no terminal (Pin) is available on the P.C.B.
when the TP (Test Point) indicated as "
3.The voltage being indicated on the schematic diagram is measured in
"Standard-Playback" mode when there is no specify mode is mentioned.
4.Although the voltage and waveform available on here is measured with standard frame,
it may be differ from actual measurement due to modification of circuit and so on.
5.The voltage being indicated here may be include observational-error (deviation) due to
internal-resistance and/or reactance of equipment. Therefore, handle the value
indicated on here as reference.
6.Use the parts number indicated on the Replacement Parts List .
7.Indication on Schematic diagrams:
S4.8. Monitor Schematic Diagram ................................................ S-10
S4.9. MIC AMP FPC Schematic Diagram .................................... S-11
S5. Print Circuit Board .................................................................. S-12
S5.1. Strobe P.C.B. ....................................................................... S-12
S5.2. BATT_Catcher P.C.B. .......................................................... S-13
S5.3. Front P.C.B. ......................................................................... S-14
S5.4. MIC AMP P.C.B. .................................................................. S-15
S5.5. Side R P.C.B. ...................................................................... S-16
S5.6. SS SW P.C.B. ...................................................................... S-16
S5.7. Monitor P.C.B. ..................................................................... S-17
S5.7.1. Monitor P.C.B. (Component Side) .................................... S-17
S5.7.2. Monitor P.C.B. (Foil Side) ................................................. S-18
S5.8. MIC AMP FPC P.C.B. .......................................................... S-19
S6. Replacement Parts List .......................................................... S-21
S7. Exploded View ....................................................................... S-29
S7.1. Frame and Casing Section (1) ............................................ S-29
S7.2. Frame and Casing Section (2) ............................................ S-30
S-1
" mark.
Circuit name being connected.
This signal is connected
OFTR FEP
to the FEP schematic diagram.
Name of Signal
S7.3. LCD Section ........................................................................ S-31
S7.4. Camera Lens Section.......................................................... S-32
S7.5. Packing Parts and Accessories Section .............................. S-33
HAVE THE SPECIAL CHARACTERISTICS