Solución De Problemas - Honeywell HeatGenius HCE840B Instruction Manual

6 HEAT SETTINGS THAT GIVE YOU CONTROL OF YOUR COMFORT
6 Ways to Heat the Space You are In - Once your heater is ON, use the control buttons on the bottom to
select the desired heat setting for your needs. Your heater will start on the Constant Hi Room heat setting
each time you turn the heater on. Here is a handy reference to help select the heat option that best suits
your desired comfort level:
FLOOR AREA – (LOW HEAT)
This setting uses the lower level heating element only to provide a comfortable, gentle heat to warm up the
floor area in front of the heater.
PERSONAL – (MODERATE HEAT)
This setting uses a moderate heat level to warm you personally wherever you may be relaxing (reading,
watching TV, etc.). The LO option ( ) provides a soothing heat level, while the HI option (
increases heat output, allowing you to adjust to your desired comfort level.
ROOM – (MODERATE-HIGH HEAT)
Best for whole room heating, use this setting to bring warmth to cooler, drafty rooms. The LO option
provides a moderate heat level, while the HI option uses maximum heat output to create a warmer
environment.
THERMOSTAT – (MODERATE-HIGH HEAT)
To set the Thermostat, press the Thermostat Control Buttons (
Temperature. The Desired Temperature will flash five times and then the Current Temperature in the room
will display as a steady number. The Thermostat can operate on either HI or LO heat levels to achieve
Desired Temperature by pressing the ( ) button under Room.
NOTE: If the Current Temperature is higher than your Desired Temperature, the heater will go into cool down
mode and then shut-off until the room temperature falls below this setting or until the Desired Temperature
is changed.
HEATPHASE™ TIMER
The new HeatPhase Timer is an auto-off feature that gradually transitions the room temperature from
warmer to cooler. The timer starts at high heat and steps down 4 different heat levels until it shuts off - over
a 2 hour period. This feature is ideal for setting a comfortable, relaxing environment. (Fig. 2) The timer can
also be toggled to start at whichever level desired.
QUIET MODE
The new Quiet Mode features uses a low heat setting and fan speed to produce a gentle "white noise" and
soothing warmth. (Fig. 3)
Fig. 2
2 Hour
Auto-off
Timer with
30 Minute
Phased
Intervals
16
) slightly
) to choose your Desired
Fig. 3
Low Heat
& "White
Noise"
Setting
CARACTERÍSTICAS DE SEGURIDAD
The Honeywell HeatGenius Ceramic Heater is equipped with several devices and features for
TM
added protection:
• A four way tip-over switch that disables the heater if it is accidently tipped in any direction. If tipped over,
the unit should be set upright and follow the OPERATION instructions.
• A high temperature safety control prevents overheating. If activated, unplug the device and wait at least
10 minutes for unit to cool. Then plug the heater back in and follow the OPERATION instructions.
• The heater is also equipped with a thermal cut-off fuse that will permanently shut down the heater should
it operate at a highter than normal temperature. If activated, the unit will need to be replaced.
• This heater was created using high quality, heat-resistant plastics and has a Cool Touch handle.
FAHRENHEIT A CELSIUS
• Presione y mantenga presionado los Botones de Control del Termostato (
cambiar entre Fahrenheit y Celsius y viceversa.
LIMPIEZA Y ALMACENAJE
It is recommended that the Honeywell HeatGenius
before off-season storage.
• Turn Off ( ) and unplug heater. Allow unit to cool.
• Use a dry cloth only to clean the external surfaces of the heater. DO NOT USE WATER, WAXES, POLISHES
OR ANY CHEMICAL SOLUTION.
• Before storing, clean the Ceramic Heater using the above-mentioned steps. Wrap the cord around the unit.
Place in its original box and store it in a cool, dry place.
• This heater does not disassemble.
SOLUCIÓN DE PROBLEMAS
Problema Solución
• Asegúrese que esté conectado y que el tomacorriente
If your Honeywell HeatGenius TM
esté funcionando.
Ceramic Heater shuts off
unexpectedly or fails to
• Verifique si hay obstrucciones. Si encuentra alguna, APAGUE el
operate, one of your heater
calefactor ( ) y desconéctelo.
safety features may have
• Permita que el calefactor se enfríe completamente, luego quite
been activated to prevent
la obstrucción. Espere por lo menos 10 minutos, luego vuelva a
overheating.
conectar el calefactor y siga las instrucciones de OPERACIÓN.
ESPECIFICACIONES DEL PRODUCTO
Modelo(s) Dimensión de la Unidad
HCE840B / 22.2 cm L x 17cm A x 32.5cm
HCE840C A, 1.45 kg
) durante tres segundos para
Ceramic Heater be cleaned at least once a month and
TM
Amperes Voltaje de la Watts Max
Unidad
12.5 120V, 60Hz 1575
BTUs
Max
5118
17