Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for McIntosh mcc602tm
Summary of Contents for McIntosh mcc602tm
- Page 1 5/10/2017 Owner’s Manual MCC602TM Power Amplifier MCC602TM McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903-2699 Phone: 607-723-3512 FAX: 607-724-0549 Digitized in Heiloo Netherland...
-
Page 2: Safety Instructions
9. Do not install near any heat sources such as radiators, McIntosh or have the same characteristics as the origi- heat ducts or other equipment that produce heat. nal part. Unauthorized substitutions may result in fire, 10. -
Page 3: Table Of Contents
6. The pin configuration for the XLR Balanced Input connectors If it is determined that your McIntosh product is in need of on the MCC602TM. Refer to the diagram for connections. repair, you can return it to your dealer. You can also return PIN 1: Shield or ground it to the McIntosh Laboratory Service Repair department. -
Page 4: Introduction
Do not combine any connections together compromising sound quality. or ground them. 9. In the event that MCC602TM Power Amplifier over heats, due · Patented Autoformers to improper ventilation and/or extremely high ambient... -
Page 5: Dimensions
General Notes con’t, Introduction, Performance Features and Dimensions Dimensions The following dimensions can assist in determining the best location for your MCC602TM. There is additional in- formation on the next page pertaining to installing the MCC602TM into your vehicle. Top View of the MCC602TM "... -
Page 6: Installation
It is recommended that a professional who is skilled in all Removing the End Caps aspects of installation and operation install the To access the MCC602TM Connecting Terminal Blocks, MCC602TM and any associated mobile audio equipment. remove the Glass Panel first (the above step) and then re-... -
Page 7: Side Panel Cooling, Connections And Switch
Mono Parallel Mode CHANNEL 1 SENSITIVITY CHANNEL 2/MONO SENSITIVITY Input Sensitivity Control Input Sensitivity Control Controls the Power Guard Receives the Amplifier Circuit when connected to Turn-ON signal from a certain McIntosh Control McIntosh Control Centers Center Digitized in Heiloo Netherland... -
Page 8: How To Connect For Two Channels
Left Tweeter Left Woofer/Midrange 1. Connect the power control cable from the Control Cen- ter Amp ON to the MCC602TM ON Connector on the right side of the Amplifier. Note: All cables should be connected to the amplifier before connecting the DC power cables to the battery. - Page 9 www.freeservicemanuals.info 5/10/2017 How to Connect for Two Channels Left Crossover Network (4 Ohms) Right Crossover Network (4 Ohms) Right Woofer/Midrange Right Tweeter Vehicle Fuse Battery Digitized in Heiloo Netherland...
-
Page 10: How To Connect For Mono Parallel
PARALLEL, both channels can be fed from the 2/MONO Input and each drive a separate speaker. In this case the Center Amp ON to the MCC602TM ON connector on speakers are connected as described in the HOW TO the right side of the amplifier. - Page 11 www.freeservicemanuals.info 5/10/2017 How to Connect for Mono Parallel Woofer (4 Ohm) Woofer (4 Ohm) Vehicle Fuse Battery Digitized in Heiloo Netherland...
- Page 12 www.freeservicemanuals.info 5/10/2017 CHANNEL 1 POWER GUARD CHANNEL 2 POWER GUARD LED lights when the Power Guard LED lights when the Power Guard Circuit activates for Amplifier Circuit activates for Amplifier Channel 1 Channel 2 CHANNEL 1 METER CHANNEL 2 METER indicates the Channel 1 indicates the Channel 2 Power Output...
-
Page 13: Top Panel Displays
Center turns On or Off. to all the Note: There must be an Amp ON connection between the musical MCC602TM and the signal source unit in order for the amplifier informa- power turn On and Off to function. tion be-... -
Page 14: How To Replace The Fuses
5/10/2017 How to Replace the Fuses How to Replace the Fuses If the MCC602TM produces no sound, no Meter Illumination, the power control and the power supply connections seem secure, one or more Remove Top Cover Screws of the Amplifier Fuse(s) may have failed. -
Page 15: Technical Description And Block Diagrams
0.002%. The true distortion read- region safe operating area. An automatic tracking bias sys- ings on the MCC602TM are so low, it takes special mea- tem completely eliminates any trace of crossover distor- suring techniques to make accurate readings. The tion. -
Page 16: Block Diagram
Refer to loud passages demanding high power, the fans will turn on figure 10. A McIntosh amplifier with an Autoformer can be to increase cooling. used to safely drive multiple speakers without reducing the life expectancy of the power amplifier. -
Page 17: Power Supply
If an amplifier chan- Protection Circuits nel is overdriven, there will be a difference between the The MCC602TM incorporates it’s version of the McIntosh two signal waveforms. When the difference exceeds 0.3% Sentry Monitor output transistor protec- (equivalent to 0.3% harmonic distortion), the POWER... -
Page 18: Specifications
www.freeservicemanuals.info 5/10/2017 Specifications Specifications Power Output Stereo Power Requirements Minimum sine wave continuous average power output per 12 Volts DC, 3.5 amps (idle) - 100 amps (600 watts) channel, all channels operating is: Dimensions 300 watts into 2 ohm load 26-7/8 inches (68.3cm) wide, 12-1/2 inches (31.75 300 watts into 4 ohm load cm) depth, 4-3/16 inches (10.64 cm) high... -
Page 19: Packing Instruction
If a shipping carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Labo- ratory. Please see the Part List for the correct part numbers. - Page 20 5/10/2017 McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No. 040730 Digitized in Heiloo Netherland...
Need help?
Do you have a question about the mcc602tm and is the answer not in the manual?
Questions and answers