Related Manuals for King Industrial KC-2405C
Summary of Contents for King Industrial KC-2405C
- Page 1 1 HP dust collector INstructIoN MANuAl MODEL: KC-2405C COPYRIGHT © 2016 ALL RIGHTS RESERVED BY KING CANADA TOOLS INC.
-
Page 2: Warranty Information
wArrANty INForMAtIoN 2-yeAr kING cANAdA tools LIMITED WARRANTY OFFERS A 2-YEAR LIMITED WARRANTY FOR THIS 1 HP DUST COLLECTOR FOR COMMERCIAL USE. ProoF oF PurcHAse Please keep your dated proof of purchase for warranty and servicing purposes. rePlAceMeNt PArts Replacement parts for this product are available at our authorized King Canada service centers across Canada. lIMIted tool wArrANty King Canada makes every effort to ensure that this product meets high quality and durability standards. -
Page 3: General Safety Instructions For Power Tools
GeNerAl sAFety INstructIoNs For Power tools 1. kNow your tool 12. AlwAys weAr sAFety GlAsses. Read and understand the owners manual and labels affixed to Always wear safety glasses (ANSI Z87.1). Everyday eyeglasses only have impact resistant lenses, thet are Not safety glasses. the tool. - Page 4 sPecIFIc sAFety INstructIoNs For your dust collector 11) Use extra care when collecting dust on stairs. 4) When cleaning the dust collector bags, wear a dust mask. 12) To avoid injury from accidental starting, unplug power cord before changing or cleaning the filter/dust bag or the chip bag. This dust collector is specifically designed to capture sawdust and 13) Do not use without the filter/dust bag and/or the chip bag in place.
-
Page 5: Electrical Information
electrIcAl INForMAtIoN wArNING! ALL ADJUSTMENTS OR REPAIRS MUST BE DONE WITH THE DUST COLLECTOR DISCONNECTED FROM THE POWER SOURCE. FAILURE TO COMPLY MAY RESULT IN SERIOUS INJURY! Power suPPly safety key is removed from the switch and placed in a safe loca- tion, unauthorized persons or children can’t turn the switch to the wArNING: YOUR DUST COLLECTOR MUST BE CONNECTED TO A On position. -
Page 6: Getting To Know
GettING to kNow your dust collector 1. Ventilation housing 2. 5” Hose 3. Hose clamp (1 of 2) 4. Top cloth filter bag (acc’y mod. KDCB-2405T-1MIC) 5. Housing 6. Motor 7. On/Off switch with safety key 8. Handle 9. Dust bag strap (1 of 2) 10. - Page 7 AsseMbly 1. Install the four casters (A) Fig.5 to the under side of the base (B). Se- cure the four casters to the base using 4 washers and acorn hex. nuts (C). Tighten using the supplied wrench. FIGure 5 2. Place base with casters (A) Fig.6 on the ground and install the motor support (B) to the base using 4 hex.
- Page 8 AsseMbly 7. Slide hose clamps (A) Fig.9 onto each end of the 5” hose (B). Attach hose between the ventilation housing (C) and the filtration housing (D). Tighten clamps to secure hose using a screwdriver. FIGure 9 8. Install bag hanger (A) Fig.10 into the mounting holes (B) in the filtration housing (C).
-
Page 9: Assembly & Maintenance
AsseMbly & MAINteNANce 10. Before installing the lower plastic dust bag, to avoid any possible air leaks it is recommended to install the adhesive foam gasket (A) Fig.12 to the lower lip of the filtration housing (B) as shown. FIGure 12 11. -
Page 10: Troubleshooting
troublesHootING ProbleM ProbAble cAuse reMedy suGGested Motor will not run. 1. Defective cord, plug, switch 1. Consult service. Any attempt to repair this motor may create a hazard unless and/or motor. repair is done by a qualified service technician. Repair service is available at 2.
Need help?
Do you have a question about the KC-2405C and is the answer not in the manual?
Questions and answers