Bosch GKS 190 Professional Original Instructions Manual page 10

OBJ_BUCH-814-003.book Page 10 Friday, December 2, 2011 12:18 PM
10 | English
External Dust Extraction
Connect the vacuum hose to a vacuum cleaner (accessory).
An overview for connecting to various vacuum cleaners can be
found at the end of this manual.
The machine can be plugged directly into the receptacle of a
Bosch all-purpose vacuum cleaner with remote starting con-
trol. The vacuum cleaner starts automatically when the ma-
chine is switched on.
The vacuum cleaner must be suitable for the material being
worked.
When vacuuming dry dust that is especially detrimental to
health or carcinogenic, use a special vacuum cleaner.
Operation
Operating Modes
Before any work on the machine itself, pull the mains
plug.
Adjusting the Cutting Depth (see figure C)
Adjust the cutting depth to the thickness of the work-
piece. Less than a full tooth of the blade teeth should be
visible below the workpiece.
Loosen the clamping lever 24. For a smaller cutting depth,
pull the saw away from the base plate 12; for a larger cutting
depth, push the saw toward the base plate 12. Adjust the de-
sired cutting depth at the cutting-depth scale. Tighten the
clamping lever 24 again.
If the cutting depth cannot be fully adjusted after loosening
clamping lever 24, pull clamping lever 24 away from the saw
and swivel it downward. Release the clamping lever 24 again.
Repeat this procedure until the requested cutting depth can
be adjusted.
If the cutting depth cannot be sufficiently locked after tighten-
ing clamping lever 24, pull clamping lever 24 away from the
saw and swivel it upward. Release the clamping lever 24
again. Repeat this procedure until the cutting depth is locked.
Adjusting the Cutting Angle
Loosen the wing bolts 6 and 26. Tilt the saw sidewards. Ad-
just the desired measure on the scale 5. Tighten the wing
bolts 6 and 26 again.
Note: For bevel cuts, the cutting depth is smaller than the set-
ting indicated on the cutting-depth scale 25.
Cutting Marks
45 0
The 0° cutting mark (9) indicates the position of the saw
blade for right-angled cuts. The 45° cutting mark (8) indi-
cates the position of the saw blade for 45° cuts.
1 619 P06 541 | (2.12.11)
For precise cuts, position the circular saw against the work-
piece as shown in the figure. It is best to carry out a trial cut.
Starting Operation
Observe correct mains voltage! The voltage of the pow-
er source must agree with the voltage specified on the
nameplate of the machine. Power tools marked with
230 V can also be operated with 220 V.
Switching On and Off
(3 601 F23 04./3 601 F23 08./3 601 F23 09./
3 601 F23 0B.)
To start the machine, first push the lock-off button for the
On/Off switch 2 and then press the On/Off switch 1 and keep
it pressed.
To switch off the machine, release the On/Off switch 1.
Note: For safety reasons, the On/Off switch 1 cannot be
locked; it must remain pressed during the entire operation.
Switching On and Off
(3 601 F23 0C./3 601 F23 0K./3 601 F23 0L.)
To start the machine, press the On/Off switch 1 and keep it
pressed.
To lock the pressed On/Off switch 1, press the lock-on button
2.
To switch off the machine, release the On/Off switch 1 or
when it is locked with the lock-on button 2, briefly press the
On/Off switch 1 and then release it.
Working Advice
Protect saw blades against impact and shock.
Guide the machine evenly and with light feed in the cutting di-
rection. Excessive feed significantly reduces the service life of
the saw blade and can cause damage to the power tool.
Sawing performance and cutting quality depend essentially
on the condition and the tooth form of the saw blade. There-
fore, use only sharp saw blades that are suited for the material
to be worked.
Sawing Wood
The correct selection of the saw blade depends on the type
and quality of the wood and whether lengthway or crossway
cuts are required.
When cutting spruce lengthways, long spiral chips are formed.
Beech and oak dusts are especially detrimental to health.
Therefore, work only with dust extraction.
Sawing with Parallel Guide (see figure D)
The parallel guide 10 enables exact cuts along a workpiece
edge and cutting strips of the same dimension.
Loosen wing bolt 7 and slide the scale of the parallel guide 10
45 0
through the guide in the base plate 12. Adjust the desired cut-
ting width as the scale setting at the respective cutting mark 9
or 8; see Section "Cutting Marks". Tighten wing bolt 7 again.
Sawing with Auxiliary Guide (see figure E)
For sawing large workpieces or straight edges, a board or
strip can clamped to the workpiece as an auxiliary guide; the
base plate of the circular saw can be guided alongside the aux-
iliary guide.
Bosch Power Tools