Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Apollo AL-A29
Summary of Contents for Apollo AL-A29
- Page 1 Alpha-Numeric Display Pager MODEL： ： ： ： AL-A29...
-
Page 2: Table Of Contents
ALA29 PAGER PROGRAMMING SOFTWARE Contents Contents GETTING STARTED .................................. 1 Equipment Required................................ 1 Equipment Setup ................................1 INSTALLING PROGRAMMER SOFTWARE ......................... 3 Installation ..................................3 Running ................................... 6 ALA29 PROGRAMMING ................................7 Introduction..................................7 Starting the Programmer..............................7 Main Menu ..................................8 Menu bar.................................. -
Page 3: Getting Started
ALA29 PAGER PROGRAMMING SOFTWARE Getting Started Getting Started The ALA29 Pager Programming software, provides the flexibility to program ALA29 pagers to meet individual requirements. To obtain the best results from the product, please take a few minutes to read this instruction guide. Equipment Required To install and operate the programmer, you need a system that meets the following minimum requirements:... - Page 4 ALA29 PAGER PROGRAMMING SOFTWARE Getting Started Computer USB Cable Type A to B AL-A29 AL-A29 Programmer Figure Figure 1 1 1 1 Programmer Hardware Connections Figure Figure Programmer Hardware Connections Programmer Hardware Connections Programmer Hardware Connections September 29, 2010...
-
Page 5: Installing Programmer Software
ALA29 PAGER PROGRAMMING SOFTWARE Installing Programmer Software Installing Programmer Software Installation Install the programmer software into a PC as follows: Uncompress the ALA29.zip and save them in a temporary directory. Double click the setup.exe file. Click on “Y”. Click “Next” on the Welcome screen. Enter your user information and click “Next”. - Page 6 ALA29 PAGER PROGRAMMING SOFTWARE Installing Programmer Software Choose where the program should be installed and click “Next”. On the Select Program Folder screen choose where you would like the program to show up in your start menu and click “Install”. September 29, 2010...
- Page 7 ALA29 PAGER PROGRAMMING SOFTWARE Installing Programmer Software If you had installed USB driver then click “Finish” on the Setup Complete screen and ALA29 Pager Programmer has been installed on your computer. If you did not install USB driver then click “OK” to install USB driver. September 29, 2010...
-
Page 8: Running
PAGER PROGRAMMING SOFTWARE Installing Programmer Software Please reboot your computer after USB driver and programming software installed. Running You now have the program installed. To run it from the Start menu/ Programs/ Gold Apollo /ALA29 Pager Programmer. September 29, 2010... -
Page 9: Ala29 Programming
“Be Programmed Mode !” for ready to go. Starting the Programmer The application can be launched from Start → Programs → Gold Apollo → ALA29 Pager Programmer. The following window appears: Input your password. If key in wrong password for 3 times, the system shuts off automatically. -
Page 10: Main Menu
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Now, the system examines that the ALA29 programmer is well installed. If any questions, the following window appears: Please re-check the ALA29 programmer and printer port are well installed or not. If the connection with the ALA29 Programmer are OK. The system enters the Main Menu. -
Page 11: Menu Bar
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Menu bar In the menu bar, there are main menus with submenus like those conventionally used in Windows applications. File | Open Open a ALA29 code-plug file. The file has the extension “.tbl”. File | Save Save the current code-plug data to a file. -
Page 12: Frequency And Capcode
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Frequency and Capcode Frequency Serial Number The serial number only reads from pager. Freq. Range You can select the range of frequency and all setting will load default value. Freq. The frequency is on which the pager operates. Baud Rate The baud rate is on which the pager operates. -
Page 13: Capcode (Decimal Address)
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Polarity It select the RF signal polarity is normal or invert. Capcode (Decimal Address) Cap #1 Please input 1st Capcode (7 Dec digits between 8 and 2097151). Enable or disable 2nd Capcode (address). Fun. Bit Click to set function bit(A、B、C、D) message control. -
Page 14: Message Type Status
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Message Display Function Bit(A、B、C、D) Message Display: Ｎ: Standard Number. Ｐ: PRC Number. Ａ: Alpha number. Ｉ: Ideographic. Ｔ: Tone Only. －: Disable. Priority Alert Control Function Bit(A、B、C、D) Priority Alert: V is Enable, - is disable. Message Type Function Bit(A、B、C、D) Message Type: Ｐ: Personal. -
Page 15: Alert And Status
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Personal and Group Alert Length The available selections for all personal and group call messages alerts are: 02: 2 sec. 08: 8 sec. 16: 16 sec. 32: 32 sec. CT: continuous. Mail Drop Alert Length The available selections for mail drop messages alerts are: --: Disable. -
Page 16: Alerts And Status
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Alerts and Status Disp Source Addr ON If it is selected, the message will show the address source at last. Lowcell Alert Enable If it is selected, the pager emits a, low battery cell alert when the battery reaches a low cell state. - Page 17 ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Battery Gauge Level-Med This value represents the battery voltage level necessary for the battery gauge to display a full battery. If the battery voltage is higher or equal to this value, the full battery gauge icon is displayed. Valid selections for 2.4V are: 2.54V, 2.50V, 2.48V, 2.46V, 2.43V, 2.40V, 2.38V, 2.35V, 2.30V and valid selections for 1.2V are: 1.58V, 1.53V, 1.48V, 1.43V, 1.39V, 1.35V, 1.29V, 1.23V, 1.19V, 1.14V, 1.09V, 1.05V, 1.00V.
- Page 18 ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming RD Key Switch Alert If it is selected, the RD key switch alert function will be enabled. Out-of Service With an out-of-service time specified by the code plug, the pager is considered “out of service” when it does not detect a POCSAG synchronization word for that time period.
-
Page 19: Manu Of Pager
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Sequential Lockout The value is a sequential lockout timer begins when a message arrives and is flagged as being sequentially locked out. If duplicate messages arrive, one of the messages is disregarded and not flagged as a duplicate. Valid selections are disabled, 30 seconds, 60 seconds, 120 seconds, 175 seconds and 240 seconds. -
Page 20: Prompts
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Delete All Off If it is selected, menu of delete all is disabled. Move To Memo Off If it is selected, menu of move to memo is disabled. Prompts September 29, 2010... -
Page 21: Prompts Edit
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Prompts Edit Each prompt can be customized in the code plug, if desired, or the defaults can be used. September 29, 2010... -
Page 22: Source Prompts
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Source Prompts Prompt Control Each prompt can be customized in the code-lug, if desired, or the defaults can be used. If selected, the text programmed is displayed at the first of the message or end of message. September 29, 2010... -
Page 23: Music & Tone
ALA29 PAGER PROGRAMMING SOFTWARE ALA29 Programming Music & Tone Following list type of alert can be customized in the code plug or select from default tones. * Be sure to remove & re-insert the battery after programming the pager to save the data.* September 29, 2010...