Orion MIS-4220 User Manual page 24

MIS-4220 / MIS-4220R / MIS-4230
Auto Power Command
ƒ
ASCII R(0x52)
Auto Power On
HEX
0x35 0x32
ASCII R(0x52)
Auto Power Off
HEX
0x35 0x32
- Auto Power On: Enables Power On by connecting AC Power
Supply even without Power On command.
- Auto Power Off: Enables Power On by connecting AC Power
Supply and sending Power On command.
Input Source Command
ƒ
ASCII R(0x52)
Input Source
Change DVI
HEX
0x35 0x32
ASCII R(0x52)
Input Source
Change PC
HEX
0x35 0x32
ASCII R(0x52)
Input Source
Change HD
HEX
0x35 0x32
ASCII R(0x52)
Input Source
Change SD/DVD
HEX 0x35 0x32
ASCII R(0x52)
Input Source
Change S-VIDEO
HEX 0x35 0x32
ASCII
R(0x52)
Input Source
Change VIDEO
HEX 0x35 0x32
- Command for selecting Input Mode
Tracking Command
ƒ
ASCII R(0x52)
Auto Tracking
HEX 0x35 0x32
ASCII R(0x52)
Manual Tracking
Frequency
HEX
0x35 0x32
ASCII R(0x52)
Manual Tracking
Phase
HEX
0x35 0x32
ASCII R(0x52)
Manual Tracking
Line Start
HEX 0x35 0x32
ASCII R(0x52)
Manual Tracking
Pixel Start
0x35 0x32
- Auto Tracking: Auto screen positioning command in Input Mode PC
- Manual Tracking: Manual screen positioning command in Inpuit
Mode PC
Downloaded From TV-Manual.com Manuals
Test Pattern Command
ƒ
M(0x4D)
ASCII R(0x52)
Test Pattern Red
0x34 0x3D
HEX 0x35 0x32
m(0x6D)
ASCII R(0x52)
Test Pattern Green
0x36 0x3D
HEX
0x35 0x32
ASCII R(0x52)
Test Pattern Blue
HEX
0x35 0x32
ASCII R(0x52)
Test Pattern White
HEX 0x35 0x32
i(0x69)
ASCII R(0x52)
0x36 0x39
Return Screen
p(0x70) 0x35 0x32
0x37 0x30
- Test Pattern Command
t(0x74)
APL Command
ƒ
0x37 0x34
ASCII R(0x52)
d(0x64)
APL On
0x36 0x34 HEX 0x35 0x32
s(0x73) ASCII
R(0x52)
APL Off
0x37 0x33
0x35 0x32
v(0x76)
- APL(Automatic Power Limit) On/Off
0x37 0x36
PDP Tx Command
ƒ
ASCII R(0x52)
PDP Tx Enable
HEX 0x35 0x32
ASCII R(0x52)
a(0x61)
PDP Tx Disable
HEX
0x35 0x32
0x36 0x31
F(0x46) - Enable: RS232 IC Output(Tx) within PDP
- Disable: RS232 IC Output(Tx) within PDP turns to High Impedance
0x34 0x36
state
Caution
P(0x50)
- Do not enable Tx of plural PDP sets at the same time
when you control MPDP.
0x35 0x30
(Make sure only one set is enabled and the other sets
L(0x4C)
are disabled. If plural sets are enabled, it may cause
malfunction.)
0x34 0x3C
Software Reset Command
X(0x58) ƒ
0x35 0x38 ASCII
R(0x52)
Software
Reset HEX 0x35 0x32
- Software Reset
44
Position Command
ƒ
5(0x35)
Position Up
0x33 0x35
6(0x36)
Position Down
0x33 0x36
7(0x37)
Position Left
0x33 0x37
8(0x38)
Position Right
0x33 0x38
9(0x39)
Position Reset
0x33 0x39
- Component, SVIDEO, Composite Video Input screen positioning
command
Global Offset Command
ƒ
x(0x78)
Global Offset On
0x37 0x38
y(0x79)
Global Offset Off
0x37 0x39
- Command to enlarge the display considering the seam between
two MPDP
- Global Offset On: To enhance the continuity between MPDPs, data
for the Seam area is erased.
H(0x48)
Video Zoom Control Command
ƒ
0x34 0x38
Video Zoom Control
S(0x53)
0x35 0x33
- - Video Zoom: Default Level is "5", controllable within "1"~"9"
Color Temp Command
ƒ
Normal Mode
Studio Mode
- Studio Mode: Sets to Colour Temperature approximately 3200K
R(0x52)
Firmware Default Command
ƒ
0x35 0x32
Firmware Default
Load
- Set values to default. Values before factory adjusting.
Infinitely Expandable
Factory Data Command
ƒ
ASCII P(0x50) u(0x75)
Factory Data Save
HEX 0x35 0x30 0x37 0x35
ASCII P(0x50) d(0x64)
Factory Data Load
HEX
0x35 0x30 0x36 0x34
ASCII P(0x50) l(0x6C) - Factory Data Save: Data Save after adjusting
- Factory Data Load: Load values of Factory Data
HEX
0x35 0x30 0x36 0x3C
User File Load Command
ƒ
ASCII P(0x50) r(0x72)
HEX 0x35 0x30 0x37 0x32
User File Load
ASCII P(0x50) S(0x53)
- Read and Load Picture Control Data from saved file
0x35 0x30 0x35 0x33
- Reference - Application: Saved Picture Control Data is saved as a
* File Format: ***.dat
* Data Structure (31 byte ASCII Code)
ASCII P(0x50) L(0x4C)
User Mode
HEX 0x35 0x30 0x34 0x3C
White Balance
ASCII
P(0x50) R(0x52)
Device PC
HEX 0x35 0x30 0x35 0x32
Device DTV
Device DVD
Device VIDEO
- Data save sequence: User Mode ~Device VIDEO
ASCII P(0x50) n(0x6E)
2.3.3 Get Data Control
HEX
0x35 0x30 0x36 0x3E
Get Data Command
ƒ
Get Data Tracking
Manual
ASCII G(0x47) N(0x4E)
Get Data PDP
HEX 0x34 0x37 0x34 0x3E
Current Status
ASCII G(0x47) O(0x4F)
Get Data Total
HEX 0x34 0x37 0x34 0x3F
White Balance
Get Data New
Total White
Balance
ASCII
F(0x46) 1(0x31)
- Command to read Data saved on EEPROM within the PDP
HEX 0x34 0x36 0x33 0x31
45
ASCII F(0x46) 2(0x32)
HEX 0x34 0x36 0x33 0x32
ASCII F(0x46) 3(0x33)
HEX
0x34 0x36 0x33 0x33
ASCII F(0x46) 6(0x36)
HEX
0x34 0x36 0x33 0x36
file as the figure adjusted by the user
Brightness, Contrast, Sharpness, Color, Tint
Gain R, Gain G, Gain B, Offset R, Offset G,
Offset B
Gain R, Gain G, Gain B, Offset R, Offset G,
Offset B
Gain R, Gain G, Gain B, Offset R, Offset G,
Offset B
Brightness, Contrast, Cr, Cb
Brightness, Contrast, Color, Tint
ASCII R(0x52) A(0x41)
HEX 0x35 0x32 0x34 0x31
ASCII R(0x52) C(0x43)
HEX
0x35 0x32 0x34 0x33
ASCII G(0x47) T(0x54)
HEX
0x34 0x37 0x35 0x34
ASCII G(0x47) P(0x50)
HEX 0x34 0x37 0x35 0x30