Summary of Contents for Pebble pebblewifi
- Page 1 Pebble Manual Please read these instructions before you begin installation to insure you have everything ready. www.pebbleair.com...
- Page 2 - Open networks - WEP 64/128 bit encryption - WPA (TKIP/AES) -WPA2 (TKIP/AES) 3. A heat-pump or air-con model supported by the Pebble Air You can scan the QR code with your smartphone to view our supported brands and models.
-
Page 3: Table Of Contents
Table of Contents Installation Instructions Model Brand Selection Multiple Users Internal Temperature Sensor LED Codes 21-24... - Page 4 ◦ Your home internet wireless connection Blinkup ◦ We use this to describe the process of connecting your Pebble device to your home Wifi Sharing ◦ The term used to describe sharing the setup you have made to anyone else with a smartphone in your household.
-
Page 5: Installation Instructions
Before fixing or mounting your Pebble unit in place you will be required to link your Pebble unit to your Wi-Fi network and will need to access the bottom of the Pebble unit. Your Wi-Fi password will also be required. The Pebble has three IR transmitters... - Page 6 Step 1: Ensure your smartphone is connected to your home or office Wi-Fi system. Step 2: Download and install the ‘Pebble Air’ app from Step 3: Have your Wi-Fi routers password on hand You can scan the QR code with your smartphone to...
- Page 7 1. Open PEBBLE Air app 2. Go to settings 3. Tap Manage Pebbles...
- Page 8 4. Tap the + sign 5. Tap ‘New Entry” ’ 6. Tap the ‘New Entry’ window and re-name the pebble, push Enter Done button then tap Blinkup Pebble...
- Page 9 7. Choose the Wi-Fi the 8. Enter the Wi-Fi password pebble is connecting to (Hint: tick ‘Show password’)
- Page 10 Please read steps 9-13 9. Place your smartphone onto a flat surface 10. Plug the Pebble into the power adaptor (the LED with the wi-fi symbol will blink ORANGE slowly). Power connection...
- Page 11 Step 9-13 12. Place the Pebble on the phone's screen before the countdown ends. (The Pebble has a light sensor on the bottom 11. Tap ‘Send BlinkUp’ and a that will receive the Wi-Fi countdown will begin information) 13. The phone screen will blink continuously for approximately 15 seconds.
-
Page 12: Model Brand Selection
GREEN again for approximately one minute. You can remove the Pebble from the phone and go to the next step, Page 13 If the LED stays on solid Green the unit is doing a firmware upgrade, please wait until it starts flashing. - Page 13 You will need to choose the brand of your air- con/heatpump with the model of its remote 1. Choose ‘Select Remote’ Select brand and remote model This is the remote model NOT the Heat-pump model 2. Brand 3. Model 4. Save...
-
Page 14: Multiple Users
How to add multiple users to your Pebble 1. Go to “Settings” Select “Share Pebble”... - Page 15 Only use the sms button if you want to text the key code to the other user, in which case you will see the SMS screen as per page 8. Note: This key will be valid for 10 minutes, if it expires simply tap “SHARE PEBBLE” again which will generate a new key code.
- Page 16 Enter the four digit code and tap the GO button, this will connect and you will now have full access and control of the relevant air-con/heat-pump. (Any changes made to the Pebble Air app by any user will be automatically pushed to every user keeping all apps in sync.)
- Page 17 Changing Wi-Fi Networks (clearing the Pebble) If your pebble has been setup before you will need to clear the settings before doing a new blinkup. To check if your pebble already has been setup: 1. Plug Pebble into AC adaptor and power on at wall ONLY –...
- Page 18 How to clear the Pebble Note: This can only be done while the Wi-Fi LED is blinking (regardless of colour) Disconnect pebble from power and wait 12 seconds – DO NOT PLUG IN UNTIL • step E • Open Pebble Air app •...
- Page 19 - Place Pebble on top of phone screen. The sensor on underside of pebble must be on phone screen to read signal from phone H. Wait 10-15 seconds until phone screen stops flashing then watch the lights on Pebble I. Remove pebble from phone J.
-
Page 20: Internal Temperature Sensor
The sensor and software have been engineered to work on an average over a period of time and will not react to every small temperature changes. The temperature will display in the Pebble Air app on your smart phone “Room Temp xx “ Where possible do not…... -
Page 21: Led Codes
The correct make and model of remote been selected in the ‘Settings’ page on the Pebble Air app (as per page 12). There is a direct line of sight between the Pebble and the heat-pump / air-con The Pebble is not facing direct sunlight... - Page 22 LED Codes: Wi-Fi BlinkUp Codes The following guide should help you identify the LED status code patterns your Pebble may blink No Wi-Fi settings amber amber BlinkUp successful green green green green BlinkUp unsuccessful WPS in progress (press green green...
- Page 23 LED Codes contunied Connected to server green green Downloading update green green Installing update green Normal operation Offline, BlinkUp enabled green amber...
- Page 24 Overview If you are having trouble configuring your Pebble with BlinkUp™, please follow the instructions in this guide. General When configuring your Pebble with BlinkUp, please ensure the following: •The Pebble is powered on. •The status LED is blinking. If your status LED is not blinking, you may need to restart your Pebble.
- Page 25 •Stuck at "Connecting to server"? Check the firewall settings on your router. The Pebble needs to make a TCP connection to port 31314; ensure this is not blocked. Only TCP 31314 needs to be open; UDP 31314 can remain closed.
- Page 26 Conditions of Warranty Pebbleair Holdings Ltd (the manufacturer) warrants that all of its products are free of defects. Any apparent fault will be rectified free of charge by Pebbleair Holdings Ltd for a period of 12 months from the date of purchase, provided that: All costs of installation, cartage, freight, travelling expenses and insurance are paid by the customer The liability of Pebbleair Holdings Ltd under these Conditions of Warranty, is limited to any defective components or workmanship directly attributed to the manufacture of this product...
- Page 27 All technologies, design and intellectual property is owned by: Pebbleair Holdings Ltd Version 1.1 Pebble Air ™ and The Pebble™ Are registered trademarks of Pebbleair Holdings Ltd BlinkUp ™ is a registered trademark of Electric Imp, USA...