Clean; Calc'n'clean; Auto.off.after; Water Filter - Bosch TCA7121RW Manual

en de
c
j >
3.sec. +
Lean
● If you want to clean the appliance, press
the.start.button.8.and.run.the.cleaning.
programme.(see."Cleaning").
c '
j >
3.sec. +
aLc n
● If you want to descale and clean the
appliance,.press.the.start.button.8.and.
run.the.Calc'n'Clean.programme.(see.

"Calc'n'Clean").

a
j > uto oFF aFter .
3.sec. +
● Turn.the.knob.6.to.enter.the.time.span.
after.which.the.appliance.should.
automatically.switch.to."energy.saving.
mode".following.drink.preparation.
A.time.between.5.minutes.and.8.hours.can.
be.set.
W
j >
3.sec. +
ater FiLter
Before a new water filter is used, it must be
rinsed..
● To do this, press the water filter firmly into
the.water.tank.11.with.the.aid.of.the.
measuring.spoon.14..Fill.the.water.tank.
with.water.up.to.the."max".mark..
● Turn.the.knob.6.to.select.
press.the.start.button.8.
P 0.5
●
Lace L container under miLk
s
Frother 
tart
● Place.a.container.with.a.capacity.of.0.5.
litres.under.the.milk.frother.10.
● Press.the.start.button.8. Water will now
flow through the filter to rinse it.
● Next,.empty.the.container..The.appliance.
is.ready.to.use.once.more.
10
'c
Lean
s
tart .and.
Note: Rinsing the filter simultaneously
activates the setting for the "change filter"
display..
You can find detailed information about the
water filter in the enclosed filter instructions.
The filter is no longer effective when the
c
hange FiLter display.appears,.or.at.the.
latest.after.2.months..It.needs.to.be.
replaced.for.reasons.of.hygiene.and.so.that.
there.is.no.build-up.of.limescale.(this.could.
damage.the.appliance).
Replacement filters can be obtained from
retailers.(TCZ7003).or.from.customer.
service.(467873)..
If no new filter.is.used,.turn.the.
n
FiLter .setting.to. o .
Note: If.the.appliance.has.not.been.used.
for.a.prolonged.period.(e.g..vacation).the.
filter should be rinsed before the appliance
is.used.again..To.do.this,.simply.dispense.a.
cup.of.hot.water.
c
j >
3.sec. +
ontrast
The.display.5.contrast.can.be.set.from.
+20
to. ..The.factory.setting.is.
● Enter.the.required.setting.with.the.knob.6.
F
j >
3.sec. +
actory settings
You.can.cancel.your.own.settings.and.
reactivate.the.factory.settings.
● To.activate.the.factory.settings,.press.the.
start.button.8.
Note:.The.appliance.can.also.be.reset.to.
the.factory.settings.using.a.combination.of.
buttons..The.appliance.must.be.switched.off.
fully.
<
● Hold down the .and.
the.on/off.switch.1.O./.I.at.the.same.time.
for.at.least.5.seconds..Press.the.start.
button.8..The.factory.settings.are.now.
reactivated.
W
ater
–20
.
+0
.
>
.buttons.4.and.