Acoustic Image Ten2 Owner's Manual

Acoustic Image Ten2 Owner's Manual

S4plus
Hide thumbs Also See for Ten2:

Advertisement

Version S4plus R1
PAY ATTENTION TO THESE SYMBOLS:
The exclamation point triangle is used to alert the user to important operating or
maintenance instructions. The lightning bolt triangle is used to alert the user to the
risk of electric shock.
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
Ten2
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water, do not expose to dripping or splashing
water, do not place objects filled with liquid on apparatus.
6) WARNING: to reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
7) Clean only with a dry cloth.
8) Do not block any ventilation openings. Install in accordance with
manufacturer's instructions.
9) Do not install near any heat sources such as radiators, heat registers, stoves
or other apparatus (including amplifiers) that produce heat.
10) This apparatus shall be connected to a mains outlet socket with a positive
grounding connection. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one wider than the
other. A grounding type plug has two blades and a third grounding prong. The
Coda
wide blade or the third prong are provided for your safety. If the provided plug
does not fit into your outlet, consult an electrician for replacement of the
Corus
obsolete outlet.
11) Protect the power cord from being walked on pinched particularly at plugs,
convenience receptacles, and the point where they exit from the apparatus.
12) Use only attachments/accessories specified by the manufacturer.
13) Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus.
14) Unplug this apparatus during lightning storms or when unused for long
periods of time.
15) Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply cord
or plug is damaged, liquid has been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to rain or moisture, does not
operate normally or has been dropped.
Clarus
To prevent electric shock, do not remove the top cover.
No user serviceable parts inside. Refer servicing to
qualified service personnel.
To completely disconnect this equipment from the AC
mains, disconnect the power supply cord from the AC
receptacle.

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Ten2 and is the answer not in the manual?

Questions and answers

Summary of Contents for Acoustic Image Ten2

  • Page 1 The lightning bolt triangle is used to alert the user to the risk of electric shock. IMPORTANT SAFETY INSTRUCTIONS 1) Read these instructions. Ten2 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water, do not expose to dripping or splashing water, do not place objects filled with liquid on apparatus.
  • Page 2: Table Of Contents

    Acoustic Image. The Acoustic Image logo is a registered trademark of Acoustic Image LLC. Coda, Corus, Coda EX , Corus EX, Ten 2, Ten2 EX, Clarus and Cabrio Docking System are trademarks of Acoustic Image LLC.
  • Page 3: Power

    SPLs may require an extension cabinet like the Coda EX, Corus EX, Ten2 EX or augmentation by a larger house system. Note that when the power switch is off and the power indicator is off, power is not completely removed from the amp.
  • Page 4: Inputs

    via a jumper on the preamp control printed circuit board. How do Note that all of the push button switches illuminate when they are in access and utilize this option is described in “Jumper Options” section the “on” position. So, a quick glance at the preamp will tell you which found on page 11.
  • Page 5: Effects Loop

    Mute Switch The speaker emulation filter is a low pass filter that modifies the preamp output to sound like a single speaker guitar amp. It rolls the A switch is provided to allow you to mute the output of the Clarus frequency off starting a 4 kHz.
  • Page 6: Pseudo Stereo Operation

    Pseudo Stereo Operation Input Tone Level The effects processor in the Clarus preamp is a stereo unit. As a result, Filter Controls a single input can be converted to a stereo output as far as the effects Low Cut are concerned. The 1/4 inch jacks labeled “Stereo Out” on the rear panel are where the pseudo stereo signals are accessed.
  • Page 7: Limiter Switch

    10 db Direct Out Pre/Post I/O Buss Limiter Switch Gnd Lift Under extreme playing conditions such as high volume or when Effects driving a low impedance speaker load, the Clarus may be pushed On/Off Phase Inv Master beyond its limits. When that happens, you will hear high distortion and Level you may even cause the overcurrent protection circuit to operate resulting in an interruption of sound.
  • Page 8: Connecting A Speaker

    The power amplifier is capable of driving speaker loads as low as 2 ohms. Use a high quality speaker system in order to get the maximum performance from the amp. The Acoustic Image Coda EX, Corus EX or Ten2 EX are excellent choices. As mentioned above, the power Removal Insertion amp is short circuit protected.
  • Page 9: Connecting An Extension Speaker

    1x10 combo Thus the Corus is more optimized for non bass instruments than the amps. In fact, the other combos can be stacked on top of the Ten2 EX other combos. In particular, guitar, keyboard and violin players will like to create a compact 3x10 system.
  • Page 10: Specifications

    17”Hx15”Wx13”D (Ten2), 14”H (EX) load including internal speakers, if 10”x8”x3.5” (Clarus) connected Weight 22 lbs (Coda, Corus, 19 lbs (EX) 32 lbs (Ten2), 25 lbs (EX) Speaker System (Coda, Corus) 4 lbs (Clarus) Woofer 10 inch, downfiring Midrange 5 inch, forward firing with 2 position level...
  • Page 11: Shoulder Strap

    Be sure to check our web site regularly, we have an FAQ section and we post helpful information for getting the most out of your Acoustic Image product. Be sure to check out our YouTube channel which is accessible from our web site, we have a video version of this manual there.
  • Page 12 --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. © 2013 Acoustic Image LLC...

This manual is also suitable for:

Coda corusClarus

Table of Contents