1. Manuals
  2. Brands
  3. Acoustic Image Manuals
  4. Amplifier
  5. Ten2 EX
  6. Owner's manual

Acoustic Image ten2 Owner's Manual

Hide thumbs Also See for ten2:
Table of Contents

Advertisement

Quick Links

See also: Owner's Manual
Enlarged version
Ten2
Ten2 EX
IMPORTANT SAFETY INSTRUCTIONS
1) Read these instructions.
2) Keep these instructions.
3) Heed all warnings.
4) Follow all instructions.
5) Do not use this apparatus near water.
6) Clean only with a dry cloth.
7) Do not block any ventilation openings. Install in accordance
with manufacturer's instructions.
8) Do not install near any heat sources such as radiators, heat
registers, stoves or other apparatus (including amplifiers) that
produce heat.
9) Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades with one
wider than the other. A grounding type plug has two blades and
a third grounding prong. The wide blade or the third prong are
provided for your safety. If the provided plug does not fit into
your outlet, consult an electrician for replacement of the
obsolete outlet.
10) Protect the power cord from being walked on pinched
particularly at plugs, convenience receptacles, and the point
where they exit from the apparatus.
11) Use only attachments/accessories specified by the
manufacturer.
12) Use only with the cart, stand, tripod, bracket, or table
specified by the manufacturer, or sold with the apparatus.
13) Unplug this apparatus during lightning storms or when
unused for long periods of time.
14) Refer all servicing to qualified service personnel. Servicing
is required when the apparatus has been damaged in any way,
such as power-supply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus, the apparatus
has been exposed to rain or moisture, does not operate
normally or has been dropped.

Advertisement

Table of Contents
loading

Related Manuals for Acoustic Image ten2

Summary of Contents for Acoustic Image ten2

  • Page 1 Ten2 Ten2 EX...

  • Page 2: Table Of Contents

    A padded case is available. The Ten2 is the loudest combo amp that we make but in designing it, we chose fidelity over efficiency so it won’t play as loudly as the typical, lower fidelity 2x10 The information in this manual is subject to change without notice.

  • Page 3: Operation

    If more volume is needed, use a Ten2 EX extension with this manual. The Ten2 will work with either 115 volt, 60 Hz AC or 230 volt, cabinet or take a feed from the Direct Out jack to a PA system or another 50 Hz AC power.

  • Page 4: Effects Loop

    PA system. In the Ten2 combo, the Direct Out signal is the combined output of the two channels. A switch is provided to allow you to select whether the output from the Direct Out jack is affected by the tone controls (post EQ) or not (pre EQ).

  • Page 5: Stereo Operation

    Docking System The amp head component of the Ten2 can be removed and used as a stand- alone amplifier. To remove the head unit, first disconnect the short speaker...

  • Page 6: Speaker Placement

    The Ten2 has two outputs on the rear panel but one of them is used to connect to the internal speaker via the short jumper cable. So, one output is available for connecting an extension cabinet.

  • Page 7: Room Coupling Control

    Ten2. It is the ideal extension Mid Control ±15 dB at 650 Hz cabinet for the Ten2 but it can also be used effectively with any of our other 1x10 Treble Control Shelving type, ±15 dB at 10 kHz combo amps.
  • Page 8 --Increase the separation between the equipment and receiver. --Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. --Consult the dealer or an experienced radio/TV technician for help. © 2010 Acoustic Image LLC...

Table of Contents