Table of Contents
Advertisement
Quick Links
MODEL
JT-S2AP-W-NE
JT-S2AP-S-NE
JT-S2A-W-NE
Unit colour
-W
INSTALLATION MANUAL
Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly.
Local installation standards should be obeyed and installation should be performed by the dealer or a qualifi ed professional.
The "INSTRUCTION MANUAL" is for the customer. Be sure to hand it to the customer.
INDEX
Safety Precautions .......................................... 2
■ Checking the installation environment ............ 3
Parts to be installed .......................................... 4
■ Main unit ................................................ 4
■ Accessories ............................................. 5
■ Required items .......................................... 5
Use environment ............................................. 6
■ Required space for installation ..................... 6
■ Suitable walls .......................................... 6
■ Installation position .................................... 6
Installation procedure ....................................... 7
■ Fixing the installation panel ........................ 8
■ Fixing the base .......................................... 8
■ Removing the terminal cover ........................ 9
■ Wiring ...................................................... 9
■ Checking the setting ................................. 11
■ Attaching the front cover .............................. 12
Checking after installation ................................. 13
Test Run ......................................................... 14
Instructions given to customer ........................... 14
Hand dryer
Heater Model
Heater-less Model
-S
(White)
(Silver)
For Dealers and Installers
− 1 −
1511876HB7401
Location of Model Name display
Location of power supply
voltage display
Single-phase 220 - 240V AC
GB
Advertisement
Table of Contents
Related Manuals for Mitsubishi JT-S2AP-W-NE
Summary of Contents for Mitsubishi JT-S2AP-W-NE
-
Page 1: Table Of Contents
1511876HB7401 Hand dryer MODEL JT-S2AP-W-NE Heater Model JT-S2AP-S-NE JT-S2A-W-NE Heater-less Model Location of Model Name display Unit colour (White) (Silver) Location of power supply voltage display Single-phase 220 – 240V AC INSTALLATION MANUAL For Dealers and Installers Read the manual thoroughly before beginning installation to ensure the unit is installed safely and correctly. -
Page 2: Safety Precautions
Safety Precautions The dangers arising from improper handling and the extents of the dangers are classifi ed and explained as shown ● below. The following may lead to death or serious Warning personal injury if handled incorrectly. Do not install in locations where they ●... -
Page 3: Checking The Installation Environment
Safety Precautions (continued) Warning Single-phase 220 – 240V AC power is used. Using the incorrect power supply may cause fi res, electric shocks or malfunctions. ■ Checking the installation environment Do not install the unit in the following types of locations. ... -
Page 4: Parts To Be Installed
Parts to be installed ■ Main unit ※ Shaded areas in the fi gure indicate antibacterial material (excluding outlet nozzle areas). ■ Front Main unit Front cover Base Settings Sensor Nozzle switches Air inlet ※ Hand drying Front cover Power light area ※... -
Page 5: Accessories
Parts to be installed (continued) ■ Accessories Mounting screws………………6 Installation panel……………1 Cord clip mounting Cord clip……… 1 (5 × 30 Type 1 tapping screws) screw (4 × 14)……… 1 ■ Required items Screwdriver Longer than 150mm ※ To mark position to insert metal screw plugs in the wall. -
Page 6: Use Environment
Use environment ■ Required space for installation Top side Unit (mm) Be sure to secure at least the Caution distances listed in the righthand Isolation Location table from walls, fl ammable distance (combustible) materials and so Above Left side Right Left side Right... -
Page 7: Installation Procedure
Installation procedure For confi rmation □ Single-phase 220 – 240V AC power is being used (using the incorrect power supply may cause fi res, electric shocks or malfunctions). □ The ground fault circuit interrupter is attached (not attaching a ground fault circuit interrupter may result in electric shocks). -
Page 8: Fixing The Installation Panel
Installation procedure (continued) ■ Fixing the installation panel Installation panel Fix the installation panel onto the wall with 4 accessory mounting screws (5 × 30). The "Installation position guide" illustrated on the Mounting screws (5 × 30) ● (Accessories) right is recommended. When installing on a wall, select a wall with a fl... -
Page 9: Removing The Terminal Cover
Installation procedure (continued) Screw ■ Removing the terminal cover Terminal cover 1. Remove the terminal cover mounting screw (1) and remove the terminal cover. ※ Be careful not to lose the cord bushing. Cord bushing Base ■ Wiring Warning Caution Make sure that the main unit Single-phase 220 –... - Page 10 Installation procedure (continued) Warning Caution Make sure that the main unit Single-phase 220 – 240V AC power is used. does not fall as the base is not Using the incorrect power supply may cause fi res, electric shocks attached to the wall with screws. or malfunctions.
-
Page 11: Checking The Setting
(approx.) 9 – 12 seconds When drying quickly 60 – 62dB (approx.) When keeping the noise level (approx.) 14 – 16 seconds 58 – 59dB down during operation ※ Drying times are based on Mitsubishi measurements. (50mg of water per hand) − 11 −... -
Page 12: Attaching The
Installation procedure (continued) 1. Pass the power cable through Screw the cord bushing and fi x it to the base again with the terminal cover Terminal mounting screw. cover 2. Check that the power cable and wires are not pinched anywhere. Cord bushing Base ■... -
Page 13: Checking After Installation
Checking after installation When fi nishing the installation work, check the items in the table below again. ● Be sure to solve a problem if any. (Otherwise the expected performance and safety cannot be ensured.) ■ Points to be checked Item Description Check... -
Page 14: Test Run
Test Run Step What to check for Check Is the proper power being used? Check the power supply Single-phase 220 – 240V AC voltage Incorrect power supply may cause malfunctions or low wind power. Turn the ground-fault circuit Are any lights in the display on? interrupter "ON"... - Page 15 HEAD OFFICE: TOKYO BLDG., 2-7-3, MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN AUTHORIZED REPRESENTATIVE IN EU: MITSUBISHI ELECTRIC EUROPE B.V. HARMAN HOUSE, 1 GEORGE STREET, UXBRIDGE, MIDDLESEX UB8 1QQ, U.K. − 15 −...
- Page 16 2006/66/EC Article 20 Information for end-users and Annex II. Français English Votre produit Mitsubishi Electric est conçu et fabriqué avec des matériels et des composants de qualité supérieure qui peuvent être Your MITSUBISHI ELECTRIC product is designed and recyclés et/ou réutilisés.
- Page 17 Dansk Mitsubishi Electric producten zijn ontwikkeld en gefabriceerd uit eerste kwaliteit materialen. De onderdelen kunnen worden Dit produkt fra MITSUBISHI ELECTRIC er designet og fremstillet gerecycled en/of worden hergebruikt. med kvalitetsmaterialer og komponenter, der kan genindvindes og/ Het symbool betekent dat de elektrische en elektronische eller genbruges.
- Page 19 CHECK SHEET FICHE DE CONTRÔLE 检查表 檢視表單 Current fuse in control circuit Fusibles à intensité du circuit de commande FUSE1 ..250 V - 20 A FUSE2 ..250 V - 5 A 控制电路內的电流保险丝 (JT-S2AP ONLY) 控制電路內的電流保險絲 FUSE3 ..250 V - 6.3 A Thermal fuse fusion temperature Température de fusion du fusible thermique 温度保险丝熔断温度...
- Page 20 Description POWER (LED1) Main cause of error When normal – Tamper prevention 30-second continuous operation (automatic return) Power-supply detection abnormality 2 blinks Power-supply noise (automatic return) Motor abnormality 1 3 blinks Motor: lock/connector detached Motor abnormality 2 4 blinks Motor: brush life limit/brush abnormality Power board temperature abnormality 5 blinks Power board: high-temperature/low-temperature...