Edid Data - LG 32LS3510 Service Manual

3) Press OK key then Message will be changed as below.
4) Plug off and on TV set, then you can see downloading
process.
5) Then, Plug off and on TV set again, and Download is
finished
3.2. Input tool option.
- Adjust tool option refer to the BOM.
■ Tool Option Input : PCBA Check Process
■ Area Option Input : Set Assembly Process
- After Input Tool Option and AC off
Before PCBA check, you have to change the Tool option and
have to AC off/on (Plug out and in)
(If missing this process, set can operate abnormally)
(1) Profile : Must be changed the option value because being
different with some setting value depend on module
maker, inch and market
(2) Equipment : adjustment remote control.
(3) Adjustment method
- The input methods are same as other chassis. (Use
IN-START key on the Adjust Remote control.)
(If not changed the option, the input menu can differ the
model spec.)
Refer to Job Expression of each main chassis ass'y
(EBTxxxxxxxx) for Option value.
*Caution: Don't Press "IN-STOP" key after completing the
function inspection.
* Caution: Don't connect HDMI cable when downloading the
EDID. If the cables are connected, Downloading of
edid could be failed.

3.3. EDID data

- EDID D/L method: The EDID data is automatically saved.
■ HD MODEL
0 1 2 3 4 5
0 00 FF FF FF FF FF FF
10 01 16 01 03 80 A0 5A
20 0F 49 4B 21 08 00 45
30 01 01 01 01 01 01 01
40 55 00 C4 8E 21 00 00
50 48 88 35 00 BC 77 21
60 47 20 54 56 0A 20 20
70 00 3A 3F 1C 44 0F 00
80 02 03 25 F1 4F 84 07
90 20 22 1F 10 23 09 07
A0 10 00 80 1E 00 01 1D
B0 00 BC 88 21 00 00 1E
C0 3E 96 00 13 8E 21 00
D0 00 26 7C 43 00 C4 8E
E0 1C 16 20 58 2C 25 00
F0 00 00 00 00 00 00 00
Copyright © LG Electronics. Inc. All rights reserved.
Only for training and service purposes
6 7 8 9 A B C D
00 1E 6D 01 00 01 01
78 0A F3 30 A4 54 46
40 01 01 61 40 01 01
1D 00 72 51 D0 1E 20
1E 1B 21 50 A0 51 00
00 00 1C 00 00 00 FC
20 20 20 20 20 00 00
0A 20 20 20 20 20 20
01 16 02 03 11 12 13
07 83 01 00 00 68 03
00 80 51 D0 1C 20 40
8C 0A D0 8A 20 E0 2D
00 18 8C 0A A0 14 51
21 00 00 98 01 1D 80
C4 8E 21 00 00 9E 00
00 00 00 00 00 00 00
3.4. ADC Calibration
3.4.1. ADC Calibration-Component
(Using External pattern)
* Required Equipments
■ Remote controller for adjustment
■ MSPG-925F/MSPG-1025/MSPG-3233 Pattern Generator
3.4.2. Process
(1) Change the Input to Component mode.
(2) Input the Component 480P@60 Hz 100% color Bar Y Pb
Pr signal into Component. (MSPG-925F Model: 212/
Pattern: 65)
(3) Press ADJ key on R/C for adjustment.
(4) Enter Password number. Password is "0413".
(5) Select "Auto-RGB" and press OK(■) key.
(6) ADC adjustment is executed automatically.
(7) When ADC adjustment is finished, this OSD appear
"COMPONENT - OK".
3.4.3. Confirmation
(1) Adjust by commanding AUTO_COLOR_ADJUST (0xF1)
0x00 0x02 instruction
(2) We confirm whether "0x77 (offset), 0x78 (gain)" address of
EEPROM "0xBE" is "0xAA" or not.
(3) If "0x77", "0x78" address of EEPROM "0xBE" isn't "0xAA",
we adjust once more
(4) We can confirm the ADC values from "0x56~0x5B"
addresses in a page "0xBE"
3.4.4. EEPROM Address
EEPROM
EEPROM Sub Address
Red Gain
Green Gain
Blue Gain
Red Offset
Green Offset
E F
01 01
Blue Offset
96 26
01 01
6E 28
1E 30
00 4C
00 FD
01 A6
14 05
0C 00
80 35
10 10
F0 16
18 71
00 00
00 2A
- 10 -
Address
0XBE
0X59
0X5A
0X5B
0x56
0X57
0X58
LGE Internal Use Only