Page 5
安全指引 安全指引 使用本产品前请仔细阅读安全防范措施。 警告 y 切勿将电视机和遥控器置于以下环境中: - 阳光直射的地方。 - 湿度较大的地方,如浴室。 - 靠近任何热源,如炉灶以及其他释放热量的设备。 - 靠近厨房台面或易于接触蒸汽或油的加湿器。 - 暴露于风雨中的地方。 - 靠近盛水的容器,如花瓶。 否则,这将导致火灾、电击、产品故障或变形。 y 切勿将产品放置会接触粉尘的地方。 这有引起火灾的危险。 y 电源插头为切断装置,插头必须始终保持可用状态。 y 手湿时切勿触摸电源插头。另外如果插头潮湿或覆盖灰尘,则将插头彻底擦干或擦 掉灰尘。 湿度过大可能发生触电危险。 y 确保电源线连接至接地线。( 除非设备没有接地线。) 否则,您可能会触电或受到人身伤害 。 y 将电源线完全固定。 如果电源线没有完全固定,可能造成火灾。 y 确保电源线远离发热物体,如加热器。 否则可能造成火灾或者触电危险。 y 切勿将较重物体或产品放置于电源线上。 否则可能导致火灾或发生触电危险。...
Page 6
安全指引 y 将电视机安装至墙面时,切勿将电视机电源线和信号线挂在电视机背面。 否则可能造成火灾或者发生触电危险。 y 切勿将太多电器设备插在同一个多插孔电源插座。 否则可能会由于过热发生火灾事故。 y 连接外部设备时,切勿使产品跌落。 否则可能造成人身伤害或损坏产品。 y 将抗潮湿材料或包装材料置于儿童无法触及的地方。 吞食抗潮湿材料,会对身体造成伤害。如不慎吞食,应强迫吞食者将其吐出来并就 近就医。另外,塑料包装材料会造成窒息。 应将材料置于儿童无法触及的地方。 y 切勿将儿童攀爬到电视机上或抱住电视机。 否则电视机可能翻倒,从而造成严重伤害。 y 将使用过的电池进行仔细处理。防止儿童不慎食用。 如不慎食用,请立即就医。 y 电源线一端连接至墙上的输入接线柱时,切勿将导体 ( 如金属块 ) 插至另一端。另外, 将电源线与墙上的输入接线柱接通后,切勿触摸电源线,否则可造成触电危险。 y 切勿将易燃物储存在产品附近。 否则可能由于易燃物处理不当,发生爆炸或火灾。 y 切勿将金属物体,如硬币、发夹、筷子、或电源线投入产品中。儿童应尤其注意。 负责可能发生触电、火灾或者人身伤害。 如异物掉到产品中,拔开电源线并联系服务中心。 y 切勿向产品泼水或用易燃物 ( 稀释剂或苯 ) 擦洗产品。 否则可能发生火灾或触电事故。...
Page 7
安全指引 y 切勿私自拆卸、维修或修改产品。 否则可能造成火灾或触电事故。 联络服务中心对产品进行检查、校准或修复。 y 如出现以下任一情况,请立即断开产品电源线并立即联络当地服务中心。 - 产品受到冲击影响。 - 产品受到损坏。 - 产品进入异物。 - 产品冒烟或出现火灾。 否则,可能造成火灾或电击。 y 如果长期不使用产品,将产品电源线断开。 覆盖灰尘可能造成火灾或者绝缘老化可能造成漏电、触电或火灾。 y 电视机不能暴露于油滴或喷雾中,不要将装有液体的物体(如:花瓶)放在设备上。...
Page 8
安全指引 注意 y 将产品安装在没有无线电波的地方。 y 室外天线与电源线之间应有充分间距,以防天线落下时室外天线于电源线接触。 如两者接触,则会导致触电。 y 禁止将产品安装在不固定的搁架或倾斜面上,并且避免将产品安在装在震动或不能 完全支撑产品的地方。 否则,产品会跌落,造成损伤。 y 如果您打算将产品安装在置物台上,则需采取措施避免产品翻转。 否则,产品会跌落,造成损伤。 y 如果将产品安装在墙内, 则需在产品背面贴上标准 VESA 安装介绍 (可选部分) 。 如果采用挂架支架 (可 选部分),则需要仔细安装,避免产品掉落。 y 只可采用制造商制定的附属装置 / 配件。 y 安装天线时,应该咨询合格技术人员。 这可能造成火灾或电脑隐患。 y 我们建议您在看电视时,至少保持距电视机荧幕 2 到 7 倍荧幕对角线的长度。 如果长时间看电视会引起视觉模糊。 y 只可采用指定电池。 否则,则易损坏遥控器。...
Page 9
安全指引 y 禁止透过从壁装电源插座上拔插产品电源插头的方式开关产品。(禁止将电源插头 用作开关。) 这样做可能会导致机械事故或触电。 y 请遵照以下安装指南,以免产品过热。 - 墙面和产品之间的距离至少为 10cm。 - 禁止将产品安装在不通风的地方。(如书架或橱柜)。 - 禁止将产品安装在地毯或垫子上。 - 确保通风口没有被桌布或窗帘遮挡。 否则,将会引起火灾。 y 注意不要触摸通风口,因为电视开太久,通风口可能会变得比较热,但这并不会影 响产品的运行或性能。 y 定期检查电气软线,如发现其外表已损坏或老化,应拔掉该软线,停止使用该电气,并由合格人员替 换该软线。 y 避免灰尘聚集在电源插头的插销或插孔上。 否则会发生火灾隐患。 y 确保电源线外观不受损坏且不受机械性损伤,如弯曲、扭结、挤压、门压或踩踏。 特别需注意插头、壁装电源插座以及电器出线处。 y 禁止用手或其他锋利的物体(如指甲、铅笔或钢笔)用力按在面板上,禁止在面板 上留下任何刮痕。 y 避免触摸荧屏或将手指长时间对着荧幕。这样可能会对荧幕造成一些临时的失真效 应。 y 当清洗产品及其部件时,首先拔掉电源,然后用一张软布进行擦洗。不得使用玻璃 清洁液、汽车或工业发光体、研磨材料或蜡、苯、酒精等。这些均可能损坏产品及 其面板。 否则,也可能引起火灾、触电、或产品损坏(变形、腐蚀或破损)。 y 只要该装置连接上...
Page 10
安全指引 y 在移动或拆卸产品时,因产品过重,所以需两人一组进行移动或拆卸。 否则会造成损失。 y 联络服务中心(每年一次)对产品的内部件进行清洗。累积的灰尘可能会引起机械 故障。 y 当仪器受损时,如当电源线或插头受损,液体溢出或有杂质掉入仪器、仪器遭雨水 冲洗或受潮,且不能正常运作或已经脱落时,需安排人员进行维修。 y 如果产品摸起来感觉很冷,当打开时有一丝丝的「闪烁」,属于正常现象,实际上 产品本身没有问题。 y 面板属于高科技薄膜电晶体产品,具备 200 万到 600 万像素的清晰度。您可能会看 到微小的黑点和 / 或彩色点(红、蓝或绿色)(表示出现故障),但这不会影响产 品的性能和可靠性。该现象同样还出现在第三方产品上,所以不予更换或退款。 y 面板取决于您收看的位置(上 / 下 / 左 / 右),由于观看角度的不同,您可能会发现 LCD 屏上会出现不同的亮度和色度。 因面板所具有的特性,所以才会出现此类现象。这跟产品的性能没有关系,也不属 于什么故障。 y 长时间显示静态影像(如广播频道标志、荧幕功能表、视屏游戏场面)可能损坏荧幕,留下影像痕迹, 也就是所谓的影像残留。产品的保修范围不包括有影像残留的产品。观看静态影像的时间不得超过 1 小时。 还有,如果您长时间观看比率为...
Page 13
安装顺序/组装和准备 注 y 显示的图像可能与电视不同。 y 电视的 OSD(荧幕显示)可能与本手册的 OSD 有所不同。 y 可用功能表和选项也可能不同于您目前正使用的输入源或产品型号。 y 在不久的将来,此系列的电视中可能还会融入新的产品功能。 y 为了减少电源损耗,电视可以以待机模式放置。并且在没有人观看的情况下,您可以关闭电视,这样 可以减少能源损耗。 y 若降低屏幕亮度,则可以明显的减少电视机功耗,并且可以减少总能耗。 安装顺序 1 打开包装箱,确认包含所有附件。 2 将底座安装到电视机上。 3 连接外部设备到电视机上。 4 确认网络连接是可用的。 只有在建立网络连接后,你才能使用电视机的网络功能。 组装和准备 附件 检查您的包装箱内是否有以下物品。 如果缺少附件,请联络您购买产品的当地经销商。 本手册中的图例可能会与实际产品和物品有差异。 注意 y 请勿使用未经核准的物品,以确保安全和产品使用寿命。 y 因使用未经批准的物品而造成的任何损坏或伤害,都不在保修范围之内。 注 y 与产品随附的一些物品,可能会因型号的不同而有所分别。 y 如产品功能升级,可能会在未事先通知的情况下,对产品或本手册中的内容进行更改。...
Page 14
安装顺序/组装和准备 下图所示仅为示意图,请以实物为准。 底座支架 / 底座 底座支架 / 底座 机身 ( 仅适用于 32LS3450) ( 仅适用于 42LS3450,42LM3450) AV MODE INPUT ENERGY SAVING FLASHBK LIST MARK MUTE MENU INFO Q.MENU ENTER BACK EXIT L/R SELECT FREEZE RATIO 遥控器和电池 (AAA) 用户手册 电源线 保护盖 缆线固定夹...
Page 15
安装顺序/组装和准备 零件和按键 注意 y 请勿使用未经核准的物品,以确保安全和产品使用寿命。 y 因使用未经批准的物品而造成的任何损坏或伤害,都不在保养范围之内。 y 一些型号上的萤幕上贴有薄膜,请勿将其撕除。 下图所示仅为示意图,请以实物为准。 按键 萤幕 SETTINGS 扬声器 INPUT 遥控感应器 智能感应器 待机显示灯(电源指示灯) 触控按键 说明 频道选择。 调整音量大小。 确定所选操作。 SETTINGS 进入主选单,保存您的输入源或退出选单。 INPUT 改变输入源。 开启或关闭电源。 1 智能感应器 - 根据周围环境调节背光度。 注 y 通过选择主选单中的“其他选项”,您可以设置待机显示灯开启或关闭。...
Page 16
安装顺序/组装和准备 y 至少由 2 人来搬运一部大电视机。 抬起和移动电视机 y 用手搬运电视机时,按照下图所示搬运电视机。 在抬起和移动电视机时,请阅读下列事项,以免造 成电视机刮伤或损坏,并按其型号大小进行安全运 输。 注意 y 任何时候都要避免碰触萤幕,否则可能会损 坏萤幕。 y 我们建议将电视机放进原本的包装箱或者包装 y 在搬运电视机时,请勿使电视机剧烈摇晃或过 材料中再做移动。 分震动。 y 在抬起和移动电视机之前,应拔掉电源线和所 y 在搬运电视机时,使电视机保持竖直。 有电缆。 请勿翻转电视机,或将其向左向右倾斜。 y 在抓握电视机时,萤幕应背对着您以免损坏。 y 牢牢抓住电视机框的顶部和底部。 y 切勿抓住透明部位、扬声器或者扬声器底部区 域。...
Page 17
安装顺序/组装和准备 装配电视机 下图所示仅为示意图,以实物为准。 【仅适用于 42 LS 3450 , 42 LM 3450 】 【仅适用于 32 LS 3450 】 2 个 4 个 M4 x 16 M4 x 16 底座支架 底座支架 底座 底座 4 个 4 个 M4 x 14 M4 x 20...
Page 18
安装顺序/组装和准备 台式安装 注意 1 抬起并将电视机倾斜至直立位置,放在桌子上。 y 将底座安装到电视机时,请放置在一块泡沫 - 与墙壁间保留出 10 cm ( 最小 ) 空间,用于 垫或者柔软保护布上,以免萤幕损坏。确保 适当通风。 没有物体压在萤幕上。 y 扭紧螺丝以免电视机向前倾斜,但不能过度 扭紧。 注 10 cm 10 cm y 在电视机安装到墙壁之前将底座按照相反顺 序从电视上卸除。 2 将电源线连接至壁装电源插座。 注意 y 请勿将电视机靠近或放置於热源之上,否则 可引致火灾或者发生损坏。 将电视机固定到桌子上 将电视机固定在桌子上,以免前倾、损坏和潜在伤 害。 将电视机安装在桌子上,并在底座背部插入和扭紧 随附的螺钉。...
Page 20
挂支架安装在与地面垂直的实体墙上。 如打算连接电视机至其他建筑材料上,请联络合格 的操作人员。 LG建议由专业安装人员帮助您安装壁挂支架。 注意 y 首先切断电源,然后再移动或安装电视机, 否则可能会触电。 10 cm y 如果在天花板或歪斜的墙壁上安装电视机, 10 cm 电视可能会坠落和导致严重伤害。应使用经 授权的 LG 壁挂支架,并且联络本地经销商 或符合资格的操作人员。 y 请勿过度扭紧螺丝,否则会对电视机造成伤 害,并且会令保养无效。 y 使用符合 VESA 标准的螺丝和壁挂支架。 错 误使用或使用错误附件造成的损伤和伤害, 不在保养范围内。 确保使用符合VESA标准的螺丝和壁挂支架。 壁挂 支架的标准尺寸见下表。 注 另购产品 ( 壁挂支架 ) y 使用列于 VESA 标准螺丝规范上的螺丝。...
Page 22
建立连接 建立连接 天线连接 使用RF缆线(75Ω)连接电视机到墙壁天线插孔。 以下仅为示意图可能与实物不符。 连接不同的外部设备至电视机,转换输入模式以选 择一个外部设备。欲获取外部设备连接的更多资 讯,可以查阅每台设备随附的手册。 可用外部设备是:硬碟接收器,DVD 播放器,录影 机,音频系统,USB 存储设备,个人电脑,游戏设 备,和其他外部设备。 注 CABLE y 外部连接设备因型号不同而有所分别。 y 不考虑电视接口顺序,将外部设备连接至电 ANTENNA 视机上。 y 若您在一部 DVD 录影机或录影机上录下电 视节目,确认将电视机信号输入线缆经一部 DVD 录影机或录影机连接至电视机上。欲获 取更多录影资讯,查阅所连接设备随附的手 册。 y 请查阅外部设备手册获取使用说明。 y 如果您连接一部游戏设备至电视上,需使用 与游戏设备随附的缆线。 注 y 在个人电脑模式中,调整解像度、垂直模式、 y 使用两台或两台以上 TV 时, 请使用信号分离器。 对比度或亮度时可能会发出噪声。如果噪声...
Page 23
AV IN VIDEO L/MONO AUDIO VIDEO AUDIO 绿 白 红 蓝 红 (* 此线 LG 不提供 ) DVD/ Blu-Ray / HD Cable Box / HD STB / PC 绿 白 红 蓝 红 (* 此线 LG 不提供 ) VIDEO AUDIO HDMI 注...
Page 24
从一部外部设备传输模拟视频和音频讯号至电视 器至电视机,并进入智能共享选单使用不同的多媒 机。按照下图所示,使用复合缆线连接外部设备与 体档案。 电视机。 AV IN VIDEO L/MONO AUDIO AUDIO VIDEO 黄 白 红 (* 此线 LG 不提供 ) (* 此线 LG 不提供 ) 注 黄 白 红 y 在关机之前请安全移除 USB 存储设备。 VIDEO AUDIO VCR/DVD/ 蓝光光碟 / HD 线缆盒...
Page 25
遥控器 遥控器 此说明书中的描述依据遥控器的实际按键。 请仔细阅读此说明书,并正确使用电视。 更换电池步骤:打开遥控后面的电池盒盖,按照正确的极性方向( 对 对 , ) 插入电池 (1.5 V AAA),合上后盖。 欲拆卸电池,请按照相反步骤进行。 注意 y 请勿将旧电池和新电池混用,否则可导致遥控器损坏。 确保遥控器对准电视机上的遥控感应器。 [ 仅适用于 32/42LS3450] 将电视机开启或待机状态。 POWER ENERGY 调整萤幕亮度以降低能源消耗。 RNERGY TV/RAD SAVING 选择Radio, TV和 DTV频道。 GUIDE INFO RATIO GUIDE 显示节目指南。 查看目前节目和萤幕信息。 INFO 调整画面大小。 改变输入源,打开电视。 Number button 输入数据。...
Page 28
维护/疑难排解 维护 清洁电视机 定期仔细清洁,可延长电视机的使用寿命。 萤幕,边框,前框和底座 y 使用干净、清洁和柔软的表面来去除灰尘或污垢。 y 用在清水或稀释中性洗涤剂中浸湿的软布表面擦拭污垢,然后立即用干布擦拭。 注意 y 避免长时间按压萤幕,因为这样可能损伤萤幕。 y 请勿用您的手指或锋利物体来推、摩擦或创击表面,因为这会造成萤幕上出现刮痕以及图像失真。 y 请勿使用任何化学剂,因为可能会损伤电视表面。 y 请勿将液体喷射到电视表面。如果水分进入电视机,就可能会引发火灾、触电或故障。 电源线 定期清理电源线上积聚的灰尘或污垢。 疑难排解 问题 解决方法 不能用遥控器控制电视机。 y 检查遥控器是否对准电视机上的遥控感应器,然后再试。 y 检查产品和遥控器之间是否有障碍物。 y 检查电池是否仍然工作并且正确安装 ( )。 对 对 没有图像显示和没有声音。 y 检查产品是否开机。 y 检查电源线是否连接至墙身插座。 y 连接其他产品,以检查墙身插座是否存在问题。 电视机突然关机。...
Page 29
规格 规格 产品规格可能会有变更,恕不另行通知。 型 号 32LS3450 42LS3450 项 目 738.0mm x 501.0mm x 185.0mm 972.0mm x 635.0mm x 212.0mm 产品尺寸 连底座 (宽 X 高 X 深) 738.0mm x 438.0mm x 86.0mm 972.0mm x 571.0mm x 86.0mm 不连底座 7.5Kg 11.8Kg 产品质量 连底座 6.9Kg 10.7Kg...
Page 33
OWNER’S MANUAL LED LCD TV / LCD TV Please read this manual carefully before operating your set and retain it for future reference. 32/42LS3450 42LM3450 Printed in China http://www.lg.com...
TABLE OF CONTENTS TABLE OF CONTENTS LICENSES OPEN SOURCE SOFTWARE NOTICE SAFETY INSTRUCTIONS - Viewing 3D Imaging (Only 3D models) INSTALLATION PROCEDURE ASSEMBLING AND PREPARING Unpacking Seperate Purchase Parts and buttons Lifting and moving the TV Setting up the TV - Attaching the stand Mounting on a table Mounting on a wall...
In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com.
SAFETY INSTRUCTIONS SAFETY INSTRUCTIONS Please read these safety precautions carefully before using the product. WARNING y Do not place the TV and remote control in the following environments: - A location exposed to direct sunlight - An area with high humidity such as a bathroom - Near any heat source such as stoves and other devices that produce heat - Near kitchen counters or humidifiers where they can easily be exposed to steam or oil...
Page 38
SAFETY INSTRUCTIONS y Do not plug too many electrical devices into a single multiple electrical outlet. Otherwise, this may result in fire due to over-heating. y Do not drop the product or let it fall over when connecting external devices. Otherwise, this may result in injury or damage to the product.
Page 39
SAFETY INSTRUCTIONS y Do not disassemble, repair or modify the product at your own discretion. Fire or electric shock accident can occur. Contact the service center for check, calibration or repair. y If any of the following occur, unplug the product immediately and contact your local service centre.
Page 40
SAFETY INSTRUCTIONS CAUTION y Install the product where no radio wave occurs. y There should be enough distance between an outside antenna and power lines to keep the former from touching the latter even when the antenna falls. This may cause an electric shock. y Do not install the product on places such as unstable shelves or inclined surfaces.
Page 41
SAFETY INSTRUCTIONS y Do not turn the product On/Off by plugging-in or unplugging the power plug to the wall outlet. (Do not use the power plug for switch.) It may cause mechanical failure or could give an electric shock. y Please follow the installation instructions below to prevent the product from overheating.
Page 42
SAFETY INSTRUCTIONS y When moving or unpacking the product, work in pairs because the product is heavy. Otherwise, this may result in injury. y Contact the service center once a year to clean the internal parts of the product. Accumulated dust can cause mechanical failure. y Refer all servicing to qualified service personnel.
SAFETY INSTRUCTIONS Viewing 3D Imaging (Only 3D models) WARNING Viewing Environment y Viewing Time - When watching 3D contents, take 5 - 15 minute breaks every hour. Viewing 3D contents for a long period of time may cause headache, dizziness, fatigue or eye strain. Those that have a photosensitive seizure or chronic illness y Some users may experience a seizure or other abnormal symptoms when they are exposed to a flashing light or particular pattern from 3D contents.
Page 44
Cautions when using the 3D glasses y Make sure to use LG 3D glasses. Otherwise, you may not be able to view 3D videos properly. y Do not use 3D glasses instead of your normal glasses, sunglasses or protective goggles.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING NOTE y Image shown may differ from your TV. y Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual. y The available menus and options may differ from the input source or product model that you are using.
(Only 32LS3450) (Depending on model) M4 x 16 M4 x 14 M4 x 20 M4 x 16 Screw for assembly (Only 42LS3450, Screw for assembly (Only 32LS3450) 42LM3450) Cinema 3D Glasses (Only 42LM3450) Seperate Purchase Wall Mounting Bracket See p. 18...
ASSEMBLING AND PREPARING Parts and buttons CAUTION y Do not use any unapproved items to ensure the safety and product life span. y Any damages or injuries by using unapproved items are not covered by the manufacturer's warranty. y Some models have a thin film attached on to the screen and this must not be removed. Image shown may differ from your TV.
ASSEMBLING AND PREPARING Lifting and moving the TV y When transporting a large TV, there should be at least 2 people. y When transporting the TV by hand, hold the TV Please note the following advice to prevent the as shown in the following illustration. TV from being scratched or damaged and for safe transportation regardless of its type and size.
ASSEMBLING AND PREPARING Setting up the TV Attaching the stand Image shown may differ from your TV. 42LS3450, 42LM3450 32LS3450 M4 x 16 M4 x 16 Stand Body Stand Body Stand Base Stand Base M4 x 14 M4 x 20...
ASSEMBLING AND PREPARING Mounting on a table CAUTION 1 Lift and tilt the TV into its upright position on a y When attaching the stand to the TV table. set, place the screen facing down on a - Leave a 10 cm (minimum) space from the cushioned table or flat surface to protect the wall for proper ventilation.
Page 51
ASSEMBLING AND PREPARING Securing the TV to a wall Using the Kensington security system (Depending on model) (This feature is not available for all models.) The Kensington security system connector is located at the rear of the TV. For more information of installation and using, refer to the manual provided with the Kensington security system or visit http://www.kensington.com.
When you attach the TV to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed CAUTION by a qualified professional installer. y Disconnect the power first, and then move or install the TV.
Not using the Desk-Type Stand 1 Gather and bind the cables with the Cable Holder on the TV back cover. Only 32LS3450 y When installing the wall mounting bracket, use the Protection cover. This will protect the opening from accumulating dust and dirt.
MAKING CONNECTIONS MAKING Antenna connection CONNECTIONS Connect the TV to a wall antenna socket with an RF cable (75 Ω). Image shown may differ from your TV. Connect various external devices to the TV and switch input modes to select an external device.
MAKING CONNECTIONS HDMI connection Component connection Transmits the digital video and audio signals from Transmits analog video and audio signals from an an external device to the TV. Connect the external external device to the TV. Connect the external device and the TV with the HDMI cable as shown. device and the TV with a component cable as shown.
MAKING CONNECTIONS Composite connection USB connection Transmits analog video and audio signals from an Connect a USB storage device such as a USB external device to the TV. Connect the external flash memory, external hard drive, or a USB device and the TV with the composite cable as memory card reader to the TV and access the My shown.
REMOTE CONTROL REMOTE CONTROL The descriptions in this manual are based on the buttons on the remote control. Please read this manual carefully and use the TV correctly. To replace batteries, open the battery cover, replace batteries (1.5 V AAA) matching ends to the label inside the compartment, and close the battery cover.
Page 58
REMOTE CONTROL Only 42LM3450 Used for viewing 3D video. Selects Radio, TV and DTV programme. Shows programme guide. Views the information of the current programme and screen. Resizes an image. Changes the input source. Accesses the saved programme list. Returns to the previously viewed programme. Use this to view 3D video.
USING THE USER GUIDE USING THE USER GUIDE User Guide allows you to more easily access the detailed TV information. User Guide 1 Press SETTINGS to access the main menus. OPTION > To set language 2 Press the RED button to access the Customer SETTING ...
MAINTENANCE / TROUBLESHOOTING MAINTENANCE Cleaning your TV Clean your TV regularly to keep the best performance and to extend the product lifespan. CAUTION y Make sure to turn the power off and disconnect the power cord and all other cables first. y When the TV is left unattended and unused for a long time, disconnect the power cord from the wall outlet to prevent possible damage from lightning or power surges.
SPECIFICATIONS Product specifications may be changed without prior notice due to upgrade of product functions. For the power supply and power consumption, refer to the label attached to the product. 32LS3450 42LS3450 MODELS 738.0 mm x 501.0 mm x 185.0 mm 972.0 mm x 635.0 mm x 212.0 mm...
Page 64
Record the model number and serial number of the TV. Refer to the label on the back cover and quote this information to your dealer when requiring any service. MODEL SERIAL...