Total Assembly Line Process; Adjustment Preparation; Ddc Edid Write; Edid Data - LG 32LD320 Service Manual

4. Total Assembly line process

4.1. Adjustment Preparation

· W/B Equipment condition
CA210 : CH 9, Test signal : Inner pattern (85IRE)
· Above 5 minutes H/run in the inner pattern. ("power on" key
of adjust remote control)
Cool 9,300 ºK
Medium 8,000 ºK
Warm 6,500 ºK
* Connecting picture of the measuring instrument
(On Automatic control)
Inside PATTERN is used when W/B is controlled. Connect to
auto controller or push Adjustment R/C POWER ON ->
Enter the mode of White-Balance, the pattern will come out
Full White Pattern
RS-232C Communication
* Auto-control interface and directions
1) Adjust in the place where the influx of light like floodlight
around is blocked. (illumination is less than 10 lux).
2) Adhere closely the Color Analyzer (CA-210) to the module
less than 10 cm distance, keep it with the surface of the
Module and Color Analyzer's prove vertically.(80° ~ 100°).
3) Aging time
- After aging start, keep the power on (no suspension of
power supply) and heat-run over 15minutes.
- Using 'no signal' or 'full white pattern' or the others,
check the back light on.
• Auto adjustment Map(RS-232C)
RS-232C COMMAND MIN
[CMD ID DATA]
Cool Mid
R Gain jg Ja
G Gain jh Jb
B Gain ji Jc
R Cut
G Cut
B Cut
** Caution **
Color Temperature : COOL, Medium, Warm.
One of R Gain/G Gain/ B Gain should be kept on 0xC0, and
adjust other two lower than C0.
(when R/G/B Gain are all C0, it is the FULL Dynamic Range
of Module)
Copyright ©2010 LG Electronics. Inc. All right reserved.
Only for training and service purposes
Downloaded From TV-Manual.com Manuals
X=0.285(±0.002)
Y=0.293(±0.002) <Test Signal>
X=0.295(±0.002) Inner pattern
Y=0.305(±0.002) (216gray,85IRE)
X=0.313(±0.002)
Y=0.329(±0.002)
CA-210
COLOR
ANALYZER
TYPE: CA-210
CENTER
(DEFAULT)
Warm Cool Mid Warm
jd 00 172 192 192
je 00 172 192 192
jf 00 192 192 172
64 64
64 64
64 64
* Manual W/B process using adjusts Remote control.
• After enter Service Mode by pushing "ADJ" key,
• Enter White Balance by pushing "
Balance".
* After done all adjustments, Press "In-start" button and
compare Tool option and Area option value with its BOM, if
it is correctly same then unplug the AC cable. If it is not
same, then correct it same with BOM and unplug AC cable.
For correct it to the model's module from factory JIG model.
* Push the "IN STOP" key after completing the function
inspection.
4.2. DDC EDID Write (RGB 128Byte )
• Connect D-sub Signal Cable to D-sub Jack.
• Write EDID Data to EEPROM(24C02) by using DDC2B
protocol.
• Check whether written EDID data is correct or not.
* For SVC main Ass'y, EDID have to be downloaded to Insert
Process in advance.
4.3. DDC EDID Write (HDMI 256Byte)
• Connect HDMI Signal Cable to HDMI Jack.
• Write EDID Data to EEPROM(24C02) by using DDC2B
protocol.
• Check whether written EDID data is correct or not.
* For SVC main Ass'y, EDID have to be downloaded to Insert
Process in advance.

4.4. EDID DATA

1) All Data : HEXA Value
2) Changeable Data :
*: Serial No : Controlled / Data:01
MAX
**: Month : Controlled / Data:00
***:Year : Controlled
****:Check sum
255
255
255
64 128
64 128
64 128
- 10 -
" key at "3. White
G
LGE Internal Use Only