Advertisement
Others in the workplace should keep a safe distance from the drill, especially when it is in operation.
3
Keep the work area as childproof as possible by using padlocks and master switches.
3
Keep drill bits clean and sharp for best and safest performance. Follow the instructions for lubrication and changing accessories.
3
Remove ill fitting clothing. Remove ties, watches, rings and other loose jewellery and contain long hair.
3
Locate the drill in a suitable working area, keep area clean and tidy and free from unrelated materials. Ensure there is adequate lighting.
3
Maintain correct balance and footing. Ensure the floor is not slippery and wear non-slip shoes.
3
Secure non-stable work piece with a clamp, vice or other adequate holding device.
3
3 Avoid unintentional starting.
DO NOT use the drill for a task it is not designed to perform.
7
DO NOT allow untrained persons to operate the drill.
7
DO NOT get the drill wet or use in damp or wet locations or areas where there is condensation.
7
DO NOT operate the drill if damaged.
7
DO NOT use drill in an area where paint fumes, solvents or flammable liquids pose a potential hazard. Keep flammable material away from
7
the drill when operating. Flammable waste, such as wipes or cleaning rags, must be placed in a closed metal container and disposed of
correctly.
DO NOT exceed the rated capacity of the drill.
7
DO NOT operate the drill if any parts are missing as this may cause failure or personal injury.
7
DO NOT leave the drill operating unattended.
7
DO NOT operate the drill when you are tired, under the influence of alcohol, drugs or intoxicating medication.
7
DO NOT pull the cable from the power supply.
7
When not in use switch the drill off, remove plug from the power supply and do not leave until the tool has come to a complete stop.
3
2. DESCripTiON
The GDM50B 5 speed bench drill is suitable for light industrial, agricultural and woodworking applications. The drill is fitted with a flip-up safety
guard and "No Volt Release" switch which prevents accidental restart after a mains power interruption. A rack and pinion feed shaft with preset depth
control for repetitive work is also included. Work clamps are also available for this drill, contact your local Sealey dealer for information.
3. TECHNiCal SpECiFiCaTiON
MODEl No:
Drilling Capacity (Chuck Size):
Spindle Nose Taper:
Swing:
Spindle centre to column:
Spindle travel:
Number of speeds:
Speed range:
Maximum Distance Spindle to Table:
Maximum Distance Spindle to Base:
Working Table Surface size:
Working Base Surface size:
Overall Base Size:
Column diameter:
Collar diameter:
Overall Height:
Motor power:
input power:
Weight:
Optional Keyless Chuck 16mm:
4. CONTENT
4.1. package content
Unpack the parts listed below and check to ensure they are in good condition. Any queries must be reported to your dealer immediately.
3 Head Assembly
3 Column with Flange
3 Adjusting Handle with Set Screw (table)
3 Pivoted Clamp Bolts (2 - table arm & bracket) 3 Bolts and Washers (4)
3 Safety Guard
3 Wedge
GDM50B/GDM50BX
16mm
MT2
314mm
127mm
60mm
5
460-2890rpm
275mm
385mm
Ø250mm
155 x 165mm
340 x 210mm
60mm
55mm
745mm
220W - 230V
370W - 230V
35kg
GDMX/KC
3 Base
3 Feed Handles and Knobs (3)
3 Table
3 Arbor
3 Hex. Keys (2)
Original Language Version
3 Chuck and Key
3 Table Arm, Bracket and Worm
3 Rack and Rack Ring
3 Screw (upper pulley cover)
3 Set Screws (2)
GDM50B (GDM50BX)
Issue: 3 - 05/03/12
Advertisement
