Page 3
CAUTION: when programming the transceiver,read the factory initial data first,then rewrite the frequency and signialing etc.,otherwise errors may occur because of different frequency band etc. User Manual applied to: LP-302 UHF FM Transceiver VHF FM Transceiver LP-302 programming software:WPS302...
Page 4
SAFeTY INFoRMATIoN FoR USeR transceiver is excellently designed with advanced technology. Please observe the following precautions to perform your obligation, prevent personal injury and ensure the safety of transceiver usage. Keep the transceiver and accessories away from children. Please do not try to open or modify the transceiver without permission, non-professionals process may also cause damage. Please use assorted battery and charger to avoid damage.
UNPACKING Please carefully unpack the transceiver.We recommend that you identify the items listed in the following table before discarding the packing material .If any items are missing or have been damaged during shipment ,pls contact with dealers immediately. Supplied accessories chart Item Number Quantity...
STANDARD ACCeSSoRIeS/oPTIoNAL ACCeSSoRIeS Standard Accessories Antenna Battery Charger Belt clip AC adaptor (12V/500mA) VHF(135~175MHz) BT FR30 LI L CHG 30B LP-84M ADA 12V UHF(400~480MHz) *1 NoTe:For the frequency band of Antenna ,please refer to label indicated in the bottom of the antenna Instruction Manual Warranty card certificate of quality...
BATTeRY INFoRMATIoN Charging operation The battery is not charged at the factory, please charge it before use. Charge the battery for the first time after purchase or extended storage (more than 2 months) may not bring the battery to its normal operating capacity. After repeating fully charge/ discharge cycle for two or three times, the operating capacity will reach the best performance.
BATTeRY INFoRMATIoN How to Charge Plug the AC adaptor into the AC outlet, and then plug the cable of the AC adaptor into the DC jack located on the back of the Charger. The Indicator lights orange (1s) and then goes out----waits to charge. Plug the battery or transceiver into the charger.
BATTeRY INFoRMATIoN LED indicator: Self-Examine STATUS No Battery Pre-charging Charge Normally Fully Charged Trouble When Power on Orange (for 1 Red Light Twinkles Red twinkles for a None Green second) for 5 Minutes long time NoTe:Trouble means battery heating,batteru-circuit or charger short-circuit. Normal charging tips When charging, orange light twinkles for 1 second and goes out, which means the charger has Self- examination:...
PRePARATIoN Installing / Removing the Li-ion Battery Match the two grooves of the battery pack with the corresponding guides on the back of the transceiver, and then push it. Press the battery pack until the release latch on the top of the transceiver locks.
PRePARATIoN Installing / Removing the Belt Clip Installing the Belt Clip: Place the belt clip to the corresponding grooves on the back of the transceiver, and then clockwise screw it. Removing the Belt Clip: Anticlockwise turn the screws to remove the belt clip. Installing the Additional Speaker/ Microphone (option) Unveil the MIC-SP jack cover and then insert the Speaker/Microphone plug into MIC-SP jack.
GeTTING ACQUAINTeD Side Panel PTT key Speaker/Microphone Reading/Writing Programming PF1 key:Trun on/off microphone Software Jack Denoising Function Belt Clip PF2 key:squelch off Battery Left Panel Right Panel...
BASIC oPeRATIoN Turn on/off Transciver Under power-off state ,please turn (PoWeR)/(VoLUMe) clockwise until beeping and current signal display on LCD,indicate turn on the transceiver. NoTe If the transceiver has programmed voice prompt function,After turning on the voice prompt the current channel . Under power-on state ,please turn (PoWeR)/(VoLUMe) anticlockwise until beeping "KADA"...
BASIC oPeRATIoN NoTe You could press [PF1] mintor key to control the background volume.Meanwhile turn (PoWeR)/(VoLUMe) to adjust volume .The volume will be adjusted more correctly when communicate with other party. Channel selection Under standby mode, turn band switch to get the channel you want:turn band switch clockwise to turn to down channel. Anticlockwise to turn to up channel.
ADVANCeD oPeRATIoN The [PF1] and [PF2] key for this model are programmable ,they could come to the follow functions by programming software. NoTe:If programme the follow functions as long key ,you need to press [PF1] /[PF2] key until reach the setting time to realize the programmed long press key function. call Under standby state ,press programmed key [PF1] / [PF2] to transmit the prestored and selected DTMF signialing.
ADVANCeD oPeRATIoN channel,pressing the programmed key of temporary deletion of the interfering channel,transceiver emits "DU"beep and temporarily deletes this channel from scan list.Restart the transceiver to add the temporarily deleted channels into scan list again. Squelch levels setup The function is for seting the receiving radio signal.When signal reach certain value you could hear the sender calling ,if not the radio will keep silence .Under standby state,press programmed key of squelch levels setup [PF1] / [PF2],the transceiver emits prompt voice about the setup quelch levels Frequency reverse...
ADVANCeD oPeRATIoN Keypad Lock Under the standby state,pressing the programmed key [PF1] / [PF2] of keypad lock ,namely the keypad function is locked. Microphone Denoising Function Under the standby state,pressing the programmed key "Microphone Denoising" the transceiver emits "DU"beep ,enable the microphone denoising fucntion.While in communciation can effectively reduce Call noise and environmental noise to make sure the receiving get the best audio effect.Press the same key again , transceiver emits "DU DU"...
ADVANCeD oPeRATIoN VoX Levels Setup This Function is setting the volume level of VOX function,higher level ,bigger volume.1-9 vox levels available. Pressing the programmed key [PF1] / [PF2] of "vox levels setup",the transceiver announce the current vox level ,press the key again to choose the 1-9 vox levels .
ADVANCeD oPeRATIoN battery capacity.When the transceiver emits "DU DU DU DU " indicate the battery capacity is full .When the battery capacity not full ,it will emits "DU". Temporary Squelch off Under the standby state,pressing the programmed key [PF1] / [PF2] of "temporary squelch off " ,transceiver emits "DU" the squelch circuit is not mute at present you could hear the background noise.Release this key ,the squelch circuit is mute .By using this function could monitor weak signial which is hard to receive.
BACKGRoUND oPeRATIoN CTCSS/DCS Decode When the transceiver edit this function ,it only can hear the orther party calling when receive the matching CTCSS/DCS signal. Other transceiver includes the same CTCSS/DCS signaling seting and no signialing seting also can hear your calling. Wide/Narrow Band Setup According to the basis of national conditions ,users can set channel spacing as 25K (wide band), 20K ( middle band) or12.5K (narrow band) to communicate on the transceiver by programming software.
BACKGRoUND oPeRATIoN Radio A Radio B Radio C Radio D ID code of the receiving party is 123 355. If the calling party uses "C23" to call, Radio A and Radio B will receive the call. If the calling party uses"CC5" to call, Radio C and Radio D will receive the call. If the calling party uses "CCC"...
BACKGRoUND oPeRATIoN TX off Users can enable or disable the Transmitting Inhibited Function in current channel by programming software. Once this function is enabled, [PTT] key becomes invalid key, and the transceiver only works in receiving mode. Scan Skip Users can choose whether to set current channel as Scan Skip by programming software. Transceiver will skip current channel during scan when it is set as Scan Skip.
BACKGRoUND oPeRATIoN Long key Time Setup Users can set the time of long key by programming software,this product have 1.0-2.5 seconds (strp is 0.5S) time of long key to choose . Voice Prompt Voice prompt function is a function for confirming input operation,wrong operation or fault state . There are three kinds of beep,Beep,Chinese report and English Report.Users can setup the desired voice prompt by programming software.
BACKGRoUND oPeRATIoN Battery Save Setup The transceiver can be set for saving battery to extend standby time .When receiving the carrier wave or doing the keypad operations,,it will instantly exit battery saving mode and come into normal working mode . OFF:Battery saving is disabled 1:2:The ratio between normal working state and battery saving mode as 1:2 1:3:The ratio between normal working state and battery saving mode as 1:3...
PRoGRAMMING SoFTWARe STARTING (TAKeS WINDoW XP FoR eXAMPLe) 1.Double click “WPS-302 setup.exe” and then go on installing as computer command. 2.Click “START” menu, choose “USB To Comport” in the WPS-302 entry from “ALL PROGRAMS” and click it. Please install USB To Comport drive program as computer command.
TRoUBLe SHooTING GUIDe eLIMINATIoN MeTHoD Problem Corrective Action The battery may be exhausting. Recharge or replace the battery. The battery may not be installed correctly. Remove the battery and install it again. No power The power switch is broken; send it to local dealers to repair. Battery touch is broken;...
ATTACHeD CHART 2 DCS Frequency Chart NoTe: 1. "N" stands for positive code. "I" stands for inverted code. 228 groups of DCS in total. 2. overstriking marks are non-standard DCS.