Roland XS-82H Reference Manual page 7

AUDIO INPUT
(continued)
Menu item
2nd level 3rd level
ANALOG-1 PHANTOM POWER
ANALOG-2
INPUT GAIN
MONO INPUT
ANALOG-1
: HPF
ANALOG-8
HDMI-1 4BAND EQUALIZER
:
HIGH GAIN
HDMI-8
HIGH FREQ
ANALOG-1
: HI-MID GAIN
ANALOG-8
HI-MID FREQ
HI-MID Q
LOW-MID GAIN
LOW-MID FREQ
LOW-MID Q
LOW GAIN
LOW FREQ
GATE
THRESHOLD
RELEASE
COMPRESSOR/
DUCKING
THRESHOLD
COMP-RATIO
COMP-ATTACK
COMP-KNEE
COMP-RELEASE
DUCK-KEY IN
SELECT
DUCK-ATTACK
DUCK-RELEASE
DUCK-HOLD
OUT1 SEND RATE
:
OUT4 SEND RATE
* This varies according
to model.
Value
OFF, ON
0 dB–64 dB
OFF, ON
OFF, ON
OFF, ON
-15 dB–0 dB–15 dB
600 Hz–8.00 kHz–12.0 kHz
-15 dB–0 dB–15 dB
20.0 Hz–2.50 kHz–10.0 kHz
0.50–1.00–16.0
-15 dB–0 dB–15 dB
20.0 Hz–2.50 kHz–10.0 kHz
0.50–1.00–16.0
-15 dB–0 dB–15 dB
50.0 Hz–112 Hz–800 Hz
OFF, ON
-50 dB– -48 dB–0 dB
30 ms–500 ms–5000 ms
OFF, COMPRESSOR, DUCKING
-50 dB– -16 dB–0 dB
1.0: 1, 1.2: 1,. 1.5: 1, 2.0: 1, 2.8: 1, 4.0: 1,
8.0: 1, 16: 1, INF: 1
0.2 ms–50 ms–100 ms
HARD, SOFT1–SOFT9
30 ms–500 ms–5000 ms
HDMI INPUT1–8, ANALOG INPUT1–8
* Default values differ according to input
channel.
0.2 ms–50 ms–100 ms
30 ms–500 ms–5000 ms
0 ms–250 ms–5000 ms
0 %–100 %
This sets phantom power on or off (R channel only).
This adjusts the input sensitivity (R channel only).
Setting this to "ON" enables monaural input.
This sets the high-pass filter on or off. Setting this to "ON" attenuates the low band
while passing the high band unchanged.
This sets the equalizer on or off.
This boosts or attenuates the high band.
This adjusts the center frequency when changing the sound quality in the high band.
This boosts or attenuates the high-midrange band.
This adjusts the center frequency when changing the sound quality in the high-
midrange band.
This adjusts the bandwidth when boosting or attenuating the high-midrange band.
This boosts or attenuates the low-midrange band.
This adjusts the center frequency when changing the sound quality in the low-
midrange band.
This adjusts the bandwidth when boosting or attenuating the low-midrange band.
This boosts or attenuates the low band.
This adjusts the center frequency when changing the sound quality in the low band.
This sets gate on or off.
This sets the level used as the threshold for removing audio. Audio that does not reach
the threshold level is removed.
This adjusts the length of time until the gate effect ends after audio falls below the
threshold.
This sets the compressor or ducking on or off.
This sets the level used as the threshold when performing audio compression
(compressor) or attenuation (ducking).
Compressor: Compression is applied to audio that exceeds the threshold level.
Ducking:
Audio that exceeds the threshold level is attenuated.
This specifies the degree of compression applied to the audio. The state in which no
compression is applied is defined as "1. "
This sets the time until the compression effect peaks after audio exceeding the
threshold is input.
This adjusts the way in which the compressor is applied to the region near the
threshold level within a range extending from steep (HARD) to gentle (SOFT9).
This adjusts the length of time until compression ends after audio falls below the
threshold.
This sets the channel to use as the key-in signal.
This sets the time until the ducking effect peaks after audio exceeding the threshold is
input.
This adjusts the time until the ducking effect disappears after the time set for "DUCK-
HOLD" has passed.
This adjusts the length of time until the ducking effect starts to end after audio falls
below the threshold.
This sets the audio send level for the respective output channel.
Description
Menu List
7