Table of Contents
Advertisement
SERVICE
PART OR ALL OF YOUR
Is the range plug disconnected from the electrical outlet? • Are house fuses blown or
RANGE DOES NOT OPERATE circuit breakers tripped? • Is the range plug loose or improperly plugged in?
Has
power supply to your home been interrupted? • Was range properly set?
F PLUS A NUMBER APPEARS This is called a FAULT CODE. If a fault code appears in the display, press the STOP/
IN THE DISPLAY AND A CON- CLEAR button. If the fault code does not reappear, reprogram oven or cooktop. If the
TINUOUS BEEP SOUNDS.
fault code reappears again, disconnect power to the range and call a servicer. If fault
(EXAMPLE: F 2)
code is displayed, the oven and cooktop will not operate.
CONTROL WILL NOT AC-
Press pad again with slightly more pressure. Ifcontrol does not accept entry, call a ser-
CEPT AN ENTRY
vicer. • Is LOCK indicator on? Allow oven to cool. LOCK indicator will turn off and oven
can be set for bake or broil operation. If LOCK indicator does not turn off after allowing
oven to cool for two hours, have a serviceman check the range.
SURFACE ELEMENTS FAIL
Is range plug disconnected from the electrical outlet? • Check circuit breaker or fuse
TO TURN ON OR HEAT FOOD boxfortrippedcircuitbreakersorblownfuses..Wascontrolproperlyset?Seepage4.
PROPERLY
• Was incorrect utensil used? • For optimum results, utensil SHOULD HAVE A FLAT
bottom. See page 8 for additional information. (NOTE: Expect cooking times to increase
if range is connected to 208 volts). ° Have serviceman check range.
FOOD NOT BAKING SATIS-
Was control properly set? See page 4.
° Are racks properly in place and in correct
FACTORILY
position for what you are baking? * Is range level? • Are you using the proper pan? ° Is
it bright, not soiled or dark colored? ° Have you used foil incorrectly? ,, Are you using
standard measuring utensils? ° Did you preheat if recommended? ° Oven tempera-
ture is incorrectly set - too low or too high. See page 11.
OVEN DOES NOT OPERATE
Is the range disconnected from the electrical power? ° Was control properly set? See
page 4.
OVEN LIGHT DOES NOT
Is bulb loose or burned out?
WORK
SERVICE
Do not attempt to service the appli-
cover for location of your model and se-
If you did not receive satisfactory serv-
ance yourself unless directed to do
rial numbers.)
ice through your servicer or Maycor you
so in this book. Contact the dealer
may contact the Major Appliance Con-
sumer Action Panel by letter including
who sold you the appliance for serv-
If you are unableto obtain service, write
your name, address, and telephone
ice.
to us. Our address is found on the rating
number, as well as the model and serial
plate. See front cover for location of rat-
numbers of the appliance.
ing plate.
HOW TO OBTAIN
SERVICE
if you are not satisfied with the local re-
MajorApplianceConsumer A ctionPanel
When your appliance requires service
sponse to your service requirements,
20 NorthWackerDrive
or replacement parts, contact your
call or write MAYCOR Appliance Parts
Chicago,
IL 60606
Dealer or Authorized Servicer. Use only
and Service Company, 240 Edwards
genuine factory or Maycor parts if re-
Street, S.E., Cleveland, TN 37311,
placement partsare necessary.Consult
(615) 472-3500. Include or have avail-
MACAP (Major Appliance Consumer
the Yellow Pages in your telephone di-
able the complete model and serial
Action Panel) is an independent agency
rectory under appliance for the service
numbers ofthe appliance, the nameand
sponsored by three trade associations
center nearest you. Be sure to include
address of the dealer from whom you
as acourt of appealson consumer corn-
your name, address, and phone num-
purchased the appliance, the date of
plaints which have not been resolved
ber, along with the model and serial
purchase and details concerning your
satisfactorily within a reasonable period
numbers of the appliance. (See front
problem,
of time.
-15-
Advertisement
Table of Contents
