Related Manuals for Campbell CD100
Summary of Contents for Campbell CD100
- Page 1 CD100 Mountable Display with Keypad Revision: 1/17 C o p y r i g h t © 2 0 1 1 - 2 0 1 7 C a m p b e l l S c i e n t i f i c ,...
- Page 3 Quotations for repairs can be given on request. It is the policy of Campbell Scientific to protect the health of its employees and provide a safe working environment, in support of this policy a “Declaration of Hazardous Material and Decontamination”...
-
Page 5: About This Manual
PLEASE READ FIRST About this manual Please note that this manual was originally produced by Campbell Scientific Inc. primarily for the North American market. Some spellings, weights and measures may reflect this origin. Some useful conversion factors: Area: 1 in... - Page 7 • Periodically (at least yearly) check electrical ground connections. WHILE EVERY ATTEMPT IS MADE TO EMBODY THE HIGHEST DEGREE OF SAFETY IN ALL CAMPBELL SCIENTIFIC PRODUCTS, THE CUSTOMER ASSUMES ALL RISK FROM ANY INJURY RESULTING FROM IMPROPER INSTALLATION, USE, OR MAINTENANCE OF TRIPODS, TOWERS, OR ATTACHMENTS TO TRIPODS AND TOWERS...
-
Page 9: Table Of Contents
7. Operation ..............7 8. Maintenance ............... 8 Figures 3-1. Connecting the CD100 to the CR1000 datalogger ....... 2 6-1. Template measurements for serial numbers less than 1311 ....4 6-2. Template measurements for serial numbers 1311 and higher ....5 6-3. -
Page 11: Introduction
Campbell Scientific dataloggers. Refer to Section 5, Specifications (p. 3) for a complete list. When properly installed, the CD100 is weather and dust resistant. As a purchased service, Campbell Scientific offers the option of installing the CD100 into an enclosure. -
Page 12: Quickstart
CD100 Mountable Display with Keypad Quickstart If the CD100 is to be mounted into an enclosure bulkhead, refer to Section 6, Installation , for instructions. (p. 3) Using an SC12 cable as shown in FIGURE 3-1, connect the 9-pin CS I/O port of a CR1000 or other compatible datalogger to the 9-pin CS I/O port on the back of the CD100. -
Page 13: Specifications
Use the template shipped with the CD100 or create a template using the measurements shown in FIGURE 6-1, Template measurements for serial numbers less than 1311. -
Page 14: Template Measurements For Serial Numbers Less Than 1311
CD100 Mountable Display with Keypad Mount the CD100 as shown in FIGURE 6-3, Profile of installed CD100. Before tightening screws, adjust the gasket to align it just inside the edges of the display. Uniformly tighten the screws, but do not over-tighten. -
Page 15: Template Measurements For Serial Numbers 1311 And Higher
CD100 Mountable Display with Keypad FIGURE 6-2. Template measurements for serial numbers 1311 and higher... -
Page 16: Profile Of Installed Cd100
CD100 Mountable Display with Keypad FIGURE 6-3. Profile of installed CD100... -
Page 17: Operation
CD100 Mountable Display with Keypad Operation An overview of keyboard functions is presented in TABLE 7-1, Keyboard Display Key Functions, and FIGURE 7-1, Display Menu Overview. Detailed descriptions are available in the datalogger manual. TABLE 7-1. Keyboard Display Key Functions... -
Page 18: Maintenance
Depending on the environment and weather tightness of the installation, dust may accumulate between the surface window and the underlying display elements. If this occurs, return the display to Campbell Scientific for cleaning. Do not disassemble the CD100. The printed circuit ribbon connecting the keypad to the display can be easily torn when not removed properly. - Page 20 Santo Domingo, Heredia 40305 SOUTH AFRICA COSTA RICA • cleroux@csafrica.co.za • info@campbellsci.cc www.campbellsci.co.za www.campbellsci.cc Campbell Scientific Southeast Asia Co., Ltd. Campbell Scientific Ltd. 877/22 Nirvana@Work, Rama 9 Road Campbell Park Suan Luang Subdistrict, Suan Luang District 80 Hathern Road Bangkok 10250...