Related Manuals for PARRY PDGFP
Summary of Contents for PARRY PDGFP
-
Page 1: Installation Instructions
INSTRUCTION REF: IN145 ISSUE No. DATE 25.02.09 Page 1 of 13 INSTALLATION INSTRUCTIONS SAFETY INSTRUCTIONS USER INSTRUCTIONS PARAGON GAS FRYER MODEL : PDGF/PDGFP www.parry.co.uk... - Page 2 Page 2 of 13 IMPORTANT PLEASE READ INSTRUCTIONS FULLY BEFORE USE MODEL PDGF FRYER & PDGFP LPG FRYER INSTALLATION INSTRUCTIONS IMPORTANT- YOUR ATTENTION IS DRAWN TO THE GAS SAFETY REGULATIONS. THIS APPLIANCE MUST ONLY BE USED IN A WELL VENTILATED AREA. IT IS RECOMMENDED THAT A MINIMUM AREA OF 450mm²...
- Page 3 When appliance is not required, turn thermostat (B) fully anti-clockwise to off position, this will leave only the pilot lit ready for when the fryer is next required. To turn the unit off completely, turn the thermostat fully anti-clockwise and the pilot knob (A) fully clockwise. www.parry.co.uk...
-
Page 4: Cleaning Instructions
6) Wash all parts thoroughly. 7) Ensure all parts are thoroughly rinsed and dried. To ensure there is no water left in the drain tube, flush with a small amount of clean cooking oil. 8) Re-assembly in reverse order. www.parry.co.uk... - Page 5 “Please note also, using old oil will reduce the flash point and therefore present a greater fire hazard and be more prone to surge boiling. Attention should also be drawn to the effect of over- wet food and too large a charge on surge boiling”. www.parry.co.uk...
- Page 6 3-4 mins 170°C Fish Fillets 5-7 mins 175°C Fritters 3-4 mins 175°C Potato Chips 2 mins 190°C Scampi 3-4 mins 175°C STAT No. TEMPERATURE 60°C 75°C 90°C 105°C 120°C 135°C 150°C 165°C 180°C 195°C 5°C ALL THE ABOVE ARE +/- www.parry.co.uk...
-
Page 7: Troubleshooting
To conserve energy, turn the thermostat knob to the OFF position during breaks in frying. MODEL PDGF FRYER TROUBLESHOOTING Piezo Ignitor not sparking Is there a short in the High Tension Lead Replace Lead Has Electrode Insulator Fractured Replace Electrode If no spark is generated At all, replace Piezo www.parry.co.uk... - Page 8 Very little Check overtemperature Check Check circuit stat for open supply supply Check Check pilot jet for thermocouple blockages and voltage clean where (minimum 15mv) necessary If all of the above are OK the control valve may be faulty www.parry.co.uk...
- Page 9 Is the temperature over 220° C Replace Does the control control stat stat operate on temp. rise when set point is low (100°C Replace Check calibration Control stat of control stat. See Installation instr. for details Manually reset overtemp. stat www.parry.co.uk...
- Page 10 PROPANE GAS G31 @ 37mbar 0.94 M³/hr BUTANE GAS G30 @ 28mbar 0.72 M³/hr G25 @ 25mbar 2.45 M³/hr G25 @ 20mbar 2.10 M³/hr APPLIANCES FOR USE ON G25 GAS WILL BE FACTORY BUILT TO INCLUDE A SEALED AIR RESTRICTOR. www.parry.co.uk...
-
Page 11: Maintenance And Service
9) Turn off the gas, remove pilot and withdraw burner assembly, clean the burner parts and ensure the injectors are clear. 10) Reassemble the pilot and main burners. 11) Go through the lighting up procedure, turn the thermostat to 150°C and allow to heat www.parry.co.uk... - Page 12 2) See previous notes for removal of pilot/thermocouple assembly, also thermostat assembly. 3) Remove screws securing valve to bracket. 4) Remove fittings from valve to fit into replacement valves, as these are not supplied with new valve. 5) Refit in reverse order. www.parry.co.uk...
-
Page 13: Safety Thermostat
INJECTORS NATURAL GAS INJECT205 INJECTORS L.P.GAS INJECT135 PILOT INJECTOR NATURAL GAS PINJ27268 PILOT INJECTOR L.P.GAS PINJ76362 THERMOCOUPLE INTERRUPTER LEAD LEADT7000 BURNERS BURNR7000 CONTROL KNOB KNOBC7000 THERMOSTAT KNOB KNOBT7000 Parry Group Ltd Town End Road Draycott Derby England DE72 3PT www.parry.co.uk...