Table of Contents
Advertisement
Using the Drill / Driver
Rechargeable Battery Display
1. The rechargeable battery display (7) indicates the level of power left in the
battery (9). To check the power of the battery, press on the trigger switch
(8) to activate the drill, and the lights will be activated.
2. When all 3 lights are lit up, the battery is fully charged. When 2 lights are
lit up, the battery is at approx 50-60%. When only 1 light is lit up, there is
approx 20% power left in the battery (9).
2 Speed gearbox
The 2 Speed Gearbox allows you to select a gear
with the optimum speed and torque to suit the
application.
NOTE: When changing the two speed high /
low gear selector (4), ensure the drill/driver is not
operating.
1. To select the LOW gear (low speed, high torque
setting), push the gear selector (4) backward,
towards the back of the drill/driver. The number
"1" will be displayed (Fig F).
2. To select the HIGH gear (high speed, low torque
setting), push the gear selector (4) forward, towards the chuck.
The number "2" will be displayed (Fig F).
Using the drill/driver
Trigger switch
1. Use the forward/reverse switch (6) to select the
direction of rotation (Fig G), then pull the trigger
(8) (Fig H). This trigger switch is an electronic
variable speed control which enables the user
to vary the speed continuously.
The speed varies according to how far the
trigger switch is depressed.
The further it is depressed the faster the chuck
will rotate and the lighter it is depressed, the
slower it will rotate.
16
e-mail: help@powertoolsupport.com
MODEL: №. 2024001 • 02/2017 • 55945
24v Lithium-ion Cordless Drill with Hammer Action
F.
1
2
The picture here shows the gear
selector forward so the drill/driver
is in High speed, with the number
2 displayed.
G.
AFTER SALES SUPPORT
1800 909 909
(toll free)
24v Lithium-ion Cordless Drill with Hammer Action
2. To stop the drill/driver, release the trigger
switch (8).
Note. The variable speed control fitted to this
drill/driver is NOT intended to be used for long
periods of time during the operation of the task
being performed. Use the variable speed to start
drill/driving and screwing tasks, and then fully
depress the trigger once the task has started.
CAUTION. Extended use of the variable speed
under load will overload and then permanently damage the speed control.
Forward/reverse switch
NOTE: You can only change the direction of rotation of the drill/driver using
the forward/reverse switch (6) when the trigger (8) is NOT depressed.
This switch will allow you to change the direction of the motor while the
trigger switch is not depressed.
1. To put in reverse mode, push in the forward/reverse switch on the side of
the drill where the arrow on the switch is pointing to the rear end of the
drill. The chuck will rotate in an anti-clockwise direction.
2. To put in forward mode, push in the forward/reverse switch on the side of
the drill where the arrow on the switch is pointing to the front end of the
drill. The chuck will rotate in an clockwise direction.
Drill/driving uses the forward mode. The reverse mode is intended for the
removal of screws and assisting to remove jammed drill/driver bits.
Adjustable torque
This drill/driver is equipped with 25 torque settings plus 1 x drill setting,
1 x screw setting and 1 x hammer setting.
The torque settings are controlled and adjusted by the torque setting collar
(2), but only affects the output when the screw function (14) is selected.
The screwdriving function (14), the drill function (15) and the hammer
function (13) are all selected using the second collar, the function selection
collar (3).
AFTER SALES SUPPORT
1800 909 909
(toll free)
Using the Drill / Driver
H.
17
e-mail: help@powertoolsupport.com
MODEL: №.2024001 • 02/2017 • 55945
Advertisement
Table of Contents
