Lincoln Electric speedtec 200c Operator's Manual
Hide thumbs
Also See for speedtec 200c:
- Operator's manual (28 pages) ,
- Operator's manual (18 pages) ,
- Operator's manual (21 pages)
Subscribe to Our Youtube Channel
Related Manuals for Lincoln Electric speedtec 200c
Summary of Contents for Lincoln Electric speedtec 200c
- Page 1 IM3049 05/2016 REV05 ® SPEEDTEC 200C OPERATOR’S MANUAL ENGLISH Lincoln Electric Bester Sp. z o.o. ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland www.lincolnelectric.eu...
-
Page 2: Declaration Of Conformity
2014/35/EU, 2014/30/EU and has been designed in compliance with the following standards: EN 60974-1:2012, EN 60974-5:2013, EN 60974-10:2014 20.04.2016 Piotr Spytek Operations Director Lincoln Electric Bester Sp. z o.o., ul. Jana III Sobieskiego 19A, 58-263 Bielawa, Poland 12/05 English English... -
Page 3: Table Of Contents
12/05 THANKS! For having chosen the QUALITY of Lincoln Electric products. Please Examine Package and Equipment for Damage. Claims for material damaged in shipment must be notified immediately to the dealer. For future reference record in the table below your equipment identification information. Model Name, Code & Serial Number can be found on the machine rating plate. -
Page 4: Safety
Failure to follow the instructions in this manual could cause serious personal injury, loss of life, or damage to this equipment. Read and understand the following explanations of the warning symbols. Lincoln Electric is not responsible for damages caused by improper installation, improper care or abnormal operation. -
Page 5: Introduction
WELDED MATERIALS CAN BURN: Welding generates a large amount of heat. Hot surfaces and materials in work area can cause serious burns. Use gloves and pliers when touching or moving materials in the work area. CYLINDER MAY EXPLODE IF DAMAGED: Use only compressed gas cylinders containing the correct shielding gas for the process used and properly operating regulators designed for the gas and pressure used. -
Page 6: Output Connections
The machine is protected from overheating by a right side of display [7] is adjusted. temperature sensor. Excessive extension of the duty cycle will cause the 6. Set Knob: Type of welding procedure and welding thermal protection circuit to activate. The image is settings is changed by this knob. - Page 7 16. Spooled Wire (for GMAW / FCAW-SS): The machine does not include a spooled wire. 10. Power Switch ON/OFF (I/O): Controls the input power to the machine. Be sure the power source is 17. Wire Spool Support: Maximum 5kg spools. Accepts connected to the mains supply before turning power plastic, steel and fiber spools onto 51mm spindle.
- Page 8 Table 2. Loading the Electrode Wire Place the spool [16] on the Spindle [20] making certain the Spindle Brake Pin [22] is put in the hole in Turn the machine off. back side of spool. Load the wire spool [16] on the spindle [20] such that the spool turns anticlockwise when the wire [15] is WARNING fed into the wire feeder.
-
Page 9: Gas Connection
Shield gas is required for welding GMAW and GTAW process. Gas flow regulator and gas hoses have been added to WARNING SPEEDTEC 200C. If force is required it is likely that the wire has missed the liner of gun. WARNING ... - Page 10 ® SPEEDTEC 200C does not include the gun necessary WARNING for FCAW-SS welding. Always fasten gas cylinder properly in vertical position in Depending on the welding process, the gun can be a special holder on the wall or on a carriage. Remember purchased separately (see "Accessories"...
- Page 11 The welding load voltage can be changed depend on the Welding GMAW, FCAW-SS Process in value of parameters are set by operators: Manual Mode In manual mode can be set: ® SPEEDTEC 200C Basic menu Advanced menu ® SPEEDTEC 200C ...
- Page 12 ARC FORCE: The output current is temporarily VRD (Voltage Reduction Device) - increased to clear short circuit connections between the GTAW / SMAW only electrode and the workpiece. This machine is provided by VRD (Voltage Reduction Device) function during welding GTAW/SMAW only. HOT START: Value in percentage of nominal value This function reduces the voltage at the output below welding current during arc start current.
- Page 13 ® Guide’s Marking Interface SPEEDTEC 200C Description of the user interface in "Quick Guide" chapter. See "Spare Parts". Select Welding Process SMAW (MMA) Welding Basic menu GMAW (MIG/MAG) Burnback Brightness Level Manual Welding View Software and FCAW- Self shielded Run-in WFS Hardware Version Manual Welding Information...
- Page 14 WARNING For any repair operations, modifications or maintenances, it is recommended to contact the nearest Technical Service Center or Lincoln Electric. Repairs and modifications performed by unauthorized service or personnel will cause, that the manufacturer’s warranty will become null and void.
-
Page 15: Electromagnetic Compatibility (Emc)
Lincoln Electric. Before installing the machine, the operator must check the work area for any devices that may malfunction because of electromagnetic disturbances. -
Page 16: Technical Specifications
Technical Specifications NAME INDEX ® SPEEDTEC 200C K14099-2 INPUT Input Voltage U EMC Group / Class Frequency 230V ± 10%, 1-phase II / A 50 / 60 Hz Input Power at Rated Cycle Input Amperes I cos φ 1max 6,2kVA @ 25% Duty Cycle (40°C) 0,99 RATED OUTPUT Open Circuit... -
Page 17: Weee
12/05 Part list reading instructions Do not use this part list for a machine if its code number is not listed. Contact the Lincoln Electric Service Department for any code number not listed. Use the illustration of assembly page and the table below to determine where the part is located for your particular code machine. -
Page 18: Accessories
Accessories K10413-25-3M The gas-cooled gun LG250 G to GMAW process - 3m KP10461-2 Gas nozzle conical Ø15mm KP10461-7 Gas nozzle extra conical Ø11mm KP10460-2 Gas nozzle cylindrical Ø20mm KP10462-2 Gas nozzle bottle Ø14mm KP10466-1 Gas nozzle bottle Ø11mm KP10463-2 Gas nozzle spot weld Ø18mm KP10441-08 Contact Tip M6x25mm ECu 0.8mm KP10441-10...
Need help?
Do you have a question about the speedtec 200c and is the answer not in the manual?
Questions and answers