Product Care And Maintenance; Mains Power Connection; Connection To The Mixer; Parallel Connection Of Two Or More Systems - Montarbo W28As Instruction Manual

28A - 24A
Important !

Product care and maintenance

• This product has been designed for use in tropical climates and
particularly warm weather conditions.
• Never place burning candles or other sources of open flame on top
of the device.
• Never expose the enclosure to heat sources (heaters or other
products that produce heat).
• Never expose the enclosure to direct sunlight, excessive vibrations
or mechanical shocks.
• Avoid operating and storing the enclosure in damp or dusty places:
this may lead to malfunctions and premature degrading of specifications.
• Avoid using the enclosure close to strong sources of electromagnetic
interferences (e.g. video monitors, high power electrical cabling).
This may lead to degradation of audio quality.
• When setting up the system up outdoors, be sure to protect it
against rain.
• Care should be taken so that objects do not fall and liquid is not
spilled onto the enclosure. In public event don't let people, musicians,
technicians or anyone put glasses, cups, ashtrays or cigarettes on the
enclosure.
• Always leave the protective grid mounted on the enclosure.
• Use a soft brush or a jet of air to clean the enclosure. Do not use
alcohol, solvents or detergents.
• Take care of your connector cables. Make sure that they are not
damaged, knotted or twisted.
• Do not force connectors and controls.
• Make sure the mains power switch is off ('0') before starting any con-
nection.
• As long as it is plugged in there can be dangerous electrical potentials
inside the device, so, before undertaking any sort of maintenance work
etc., always make sure it has been unplugged from the mains socket.
12
ENGLISH
bi-amped, active loudspeaker systems

Mains power connection

• Make sure the mains power switch is off ('0').
• Check that mains voltage corresponds to the voltage indicated
on the panel, under the mains socket.
• Use only the factory supplied mains cable or, if a different plug style
is needed, a suitable cable with a ground connection and marked with
the safety approvals valid in the country of use.
• Leave enough room to get to the mains power socket and the mains
connector on the back panel.
As long as it is plugged in there can be dangerous electrical potentials
inside the device, even when the mains switch is in the '0' (off) position
and the power indicator is off so, before undertaking any sort of
maintenance work etc., always make sure it has been unplugged from
the mains socket

Connection to the mixer

If the mixer has XLR balanced outputs: use standard balanced XLR
connectors.
If the mixer has XLR unbalanced outputs: in this case, unless using
a Montarbo mixer, make sure that the XLR outputs on the mixer are
unbalanced to IEC 268 standard 1 = GND, 2 = HOT, 3 = GND.
If the mixer has JACK balanced outputs (stereo jacks): it is
possible to use stereo jack-XLR adapters, wired according to IEC 268
pin 1 = ground (sleeve), pin 2 = tip, pin 3 = ring.
If the mixer has JACK unbalanced outputs (mono jacks):
use suitable Jack-XLR male adapters unbalanced according to IEC 268
pin 1 = ground, pin 2 = tip, pin 3 = ground.
 See 'connectors' at page 37.
• Always use only heavy gauge, high quality SHIELDED cables
(signal cables).
• Always make sure that the mixer and the powered enclosures are
switched off before connecting them.
This will to avoid annoying noises and signal peaks, which can also be
dangerous for the enclosures themselves.

Parallel connection of two or more systems

• Always use only heavy gauge, high quality SHIELDED cables (signal
cables). Connect the LINK OUT socket of the first system to the LINK IN
socket the second system and the LINK OUT of the second system to
the LINK IN of the third, and so on.
 See 'connection examples' at page 38.