Zenith Z42PJ240 Installation And Operating Manual page 92

APPENDIX
1 1 2 2 . . O O S S D D S S e e l l e e c c t t ( ( C C o o m m m m a a n n d d : : k k l l ) )
To select OSD (On Screen Display) on/off.
Transmission [k][l][ ][Set ID][ ][Data][Cr]
Data 00: OSD off
Acknowledgement [l][ ][Set ID][ ][OK/NG][Data][x]
1 1 3 3 . . R R e e m m o o t t e e C C o o n n t t r r o o l l L L o o c c k k M M o o d d e e ( ( C C o o m m m m a a n n d d : : k k m m ) )
To lock the remote control and the front panel controls
on the TV.
Transmission [k][m][ ][Set ID][ ][Data][Cr]
Data 00: Lock off
Acknowledgement [m][ ][Set ID][ ][OK/NG][Data][x]
If you're not using the remote control and front panel
controls on the TV, use this mode. When main power is
on/off, remote control lock is released.
1 1 4 4 . . T T r r e e b b l l e e ( ( C C o o m m m m a a n n d d : : k k r r ) )
To adjust treble.
You can also adjust treble in the AUDIO menu.
Transmission [k][r][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Acknowledgement [r][ ][Set ID][ ][OK/NG][Data][x]
1 1 5 5 . . B B a a s s s s ( ( C C o o m m m m a a n n d d : : k k s s ) )
To adjust bass.
You can also adjust bass in the AUDIO menu.
Transmission [k][s][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Acknowledgement [s][ ][Set ID][ ][OK/NG][Data][x]
1 1 6 6 . . B B a a l l a a n n c c e e ( ( C C o o m m m m a a n n d d : : k k t t ) )
To adjust balance.
You can also adjust balance in the AUDIO menu.
Transmission [k][t][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Acknowledgement [t][ ][Set ID][ ][OK/NG][Data][x]
1 1 7 7 . . C C o o l l o o r r T T e e m m p p e e r r a a t t u u r r e e ( ( C C o o m m m m a a n n d d : : x x u u ) )
To adjust color temperature.
You can also adjust color temperature in the PICTURE menu.
Transmission [x][u][ ][Set ID][ ][Data][Cr]
Data Min: 00 ~ Max: 64 (*transmit by Hexadecimal code)
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
1 1 8 8 . . I I S S M M M M e e t t h h o o d d ( ( C C o o m m m m a a n n d d : : j j p p ) )
To avoid having a fixed image remain on screen.
Transmission [ j ][p][ ][Set ID][ ][Data][Cr]
Data 02: Orbiter
92
Data 01: OSD on
Data 01: Lock on
04: White Wash
08: Normal
Acknowledgement [p][ ][Set ID][ ][OK/NG][Data][x]
1 1 9 9 . . P P o o w w e e r r s s a a v v i i n n g g ( ( C C o o m m m m a a n n d d : : j j q q ) )
To control the low energy function on/off.
Transmission [ j ][q][ ][Set ID][ ][Data][Cr]
Data 00: Power saving off
01: Power saving: Minimum
02: Power saving: Medium
03: Power saving: Maximum
05: Screen Off
10: Intelligent Sensor
Acknowledgement [q][ ][Set ID][ ][OK/NG][Data][x]
2 2 0 0 . . A A u u t t o o C C o o n n f f i i g g u u r r a a t t i i o o n n ( ( C C o o m m m m a a n n d d : : j j u u ) )
To adjust picture position and minimize image shaking
automatically. Auto configuration only works in RGB-PC
mode.
Transmission [ j ][u][ ][Set ID][ ][Data][Cr]
Data 1: To set
Acknowledgement [u][ ][Set ID][ ][OK/NG][Data][x]
2 2 1 1 . . C C h h a a n n n n e e l l T T u u n n i i n n g g ( ( C C o o m m m m a a n n d d : : m m a a ) )
To tune channel to following physical/major/minor number.
Transmission [m][a][ ][Set ID][ ][Data00][ ][Data01]
[ ][Data02][ ][Data03][ ][Data04][ ][Data05][Cr]
Digital channels have a Physical, Major, and Minor channel
number. The Physical number is the actual digital channel
number, the Major is the number that the channel should
be mapped to, and the Minor is the sub-channel. Since
the ATSC tuner automatically maps the channel to the
Major number, the Physical number is not required when
sending a command.
Data 00: Physical Channel Number
NTSC air: 02~45, NTSC cable: 01, 0E~7D
ATSC air: 01~45, ATSC cable: 01~87
Data 01 & 02: Major Channel Number
Data 01: High byte
Two bytes are available for the Major and Minor, nor-
mally only the second byte is used.
Data 03 & 04: Minor Channel Number
Not needed for NTSC.
20: Color Wash
Data 02: Low byte