LED lighting system
No. 41001RC
1.
iNtENDED usE
The lighting system is designed for retrofitting model airplanes and model helicopters. Fitting this product
makes model airplanes and model helicopters look even more realistic and enhances their visual appearance.
Thanks to its multi-coloured and flashing components, the lighting system enables safe navigation during
night flights.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you use the product
for purposes other than those described above, the product may be damaged. In addition, improper use can
cause hazards such as short circuiting, fire, electric shock etc. Read the instructions carefully and keep them.
Make this product available to third parties only together with its operating instructions.
2.
DELivERy CoNtENt
>
Control unit
>
5 x white LEDs
>
3 x red LEDs
>
1 x green LED
>
4 x extension cables
>
Operating instructions
3.
safEty iNstRuCtioNs
Read the operating instructions carefully and especially observe the safety information. if
you do not follow the safety instructions and information on proper handling in this manual,
we assume no liability for any resulting personal injury or damage to property. such cases
will invalidate the warranty/guarantee.
Persons / Product
>
The components are breakable. Always handle them with the greatest care.
>
Do not try pulling the plug on the cable. Always hold plug and socket with one hand each when connecting
or disconnecting them from each other.
>
When fitting the product, take care that it never comes into contact with oil or water. The product is not
waterproof.
>
Do not install the control unit in a position where strong vibrations may occur.
>
Install the LEDs and control unit 2 cm (minimum) away from the receiver. This prevents malfunctions.
>
The device is not a toy. Keep it out of the reach of children and pets.
>
Protect the product from extreme temperatures, direct sunlight, strong jolts, high humidity, moisture,
flammable gases, vapours and solvents.
>
Do not place the product under any mechanical stress.
>
If it is no longer possible to operate the product safely, take it out of operation and protect it from any
accidental use. Safe operation can no longer be guaranteed if the product:
-
is visibly damaged,
-
is no longer working properly,
-
has been stored for extended periods in poor ambient conditions or
-
has been subjected to any serious transport-related stresses.
>
Also observe the safety and operating instructions of any other devices which are connected to the
product.
Miscellaneous
>
Consult an expert when in doubt about operation, safety or connection of the device.
>
Maintenance, modifications and repairs are to be performed exclusively by an expert or at a qualified
shop.
>
If you have questions which remain unanswered by these operating instructions, contact our technical
support service or other technical personnel.
4.
assEMBLy
For assembly, you will need modelling adhesive. This is not included in delivery.
When drilling, ensure no other components can be damaged. If in doubt, disassemble fragile
components first, before starting to drill holes into the housing.
If you use the extension cables, hold the socket and plug in separate hands. Press the plug down,
so that the safety pins disengage, before removing the plug from the socket.
1.
Position the individual LEDs in your model airplane or model helicopter exactly as illustrated in the
diagram.
airplane
5
4
1
3
Helicopter
5
4
3
4
4
Version 11/11
3
4
1
(1) Navigation light Red,1 red LED
(2) Navigation light Green,1 green LED
(3) Stroboscope lights, 2 white LEDs
2.
Drill the holes carefully into the housing. The drill holes must have a diameter of 5 mm.
3.
Insert the LEDs into the drill holes and fasten them with modelling adhesive.
4.
Connect the LED cables to the control unit. Please find the detailed configuration in the table.
5.
Extend the cables, if required, using the extension cables.
6.
Fasten the lighting system's control unit within the housing in a clean, dry and vibration-free position. For
example, use double-faced adhesive tape for the installation.
7.
Plug the control unit's Futaba J type plug into your receiver. Use a channel for a switch with 3 positions to
fully utilise the lighting system.
8.
Secure all cables with cable ties.
5.
oPERatioN
Note the operating instructions of your receiver and your remote control regarding proper
configuration.
>
The lighting system features three switchable modes.
>
It automatically detects the signal type (analogue or digital) and the switch type.
>
It can be operated by a switch with three positions, or by a switch with two positions, as required. When
operating it using a switch with two positions, only two modes are selectable.
Mode 0: Off mode, all LEDs off
Mode 1: Flying mode, signal lighting on, landing light off
Mode 2: Landing mode, all lights on
Frequency / cycle
50 Hz / 20 ms
Frequency / cycle
400 Hz / 2.5 ms
>
If no PWM signal is detected, Mode 2 will be automatically activated.
>
If the PWM signal cannot be identified, the current mode will be kept.
6.
DisPosaL
In order to preserve, protect and improve the quality of environment, protect human health and
utilise natural resources prudently and rationally, the user should return unserviceable product to
relevant facilities in accordance with statutory regulations.
The crossed-out wheeled bin indicates the product needs to be disposed separately and not as
municipal waste.
7.
tECHNiCaL Data
Input voltage / current:
Output voltage / current:
Cable length :
3
1
Plug type:
Dimensions (W x H x D):
Weight:
These operating instructions are published by CEI Conrad Electronic International (HK) Limited,
28th Floor & 2903-9, Pacific Plaza, 418 Des Voeux Road West, Hong Kong.
All rights including translation reserved. Reproduction by any method, e.g. photocopy, microfilming, or the
capture in electronic data processing systems require the prior written approval by the editor. Reprinting, also
in part, is prohibited.
The operating instructions reflect the current technical specifications at time of print. We reserve the right to
change the technical or physical specifications.
© 2011 by CEi Conrad Electronic international (HK) Limited
4
1
2
3
(4) Collision warning lights, 2 red LEDs
(5) Landing light, 3 white LEDs
Channel
Landing light (Land. White)
Navigation light Red (Nav. Red)
Navigation light Green (Nav. Green)
Collision warning light (Bea. Red)
Stroboscope light (Str. White)
analogue PWM
Switch 2 positions
Mode 2
Mode 0
1 ms
2 ms
Digital PWM
Switch 2 positions
Mode 2
Mode 0
1 ms
2 ms
4.8 – 6 V/DC, 200 mA max.
3 V/DC, 100 mA
200 mm
Futaba J type
35 x 40 x 8 mm
16 g
2
3
Colour
function
white
permanently on
red
permanently on
green
permanently on
red
flashes slowly
white
flashes quickly
Switch 3 positions
Mode 2
Mode 1
Mode 0
1 ms
1.5 ms
2 ms
Switch 3 positions
Mode 2
Mode 1
Mode 0
1 ms
1.5 ms
2 ms
V3_1111-JU