Page 1
Owners Manual C41 Audio Control Center McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, New York 13903 2699 Phone: 607 723 3512 FAX: 607 724 0549...
The lightning flash with arrowhead, The exclamation point within an equi- within an equilateral triangle, is intended lateral triangle is intended to alert the user to the presence of important to alert the user to the presence of operating and maintenance (servic- uninsulated dangerous voltage...
McIntosh or have the same characteristics as the origi- If it is determined that your McIntosh product is in need of nal part. Unauthorized substitutions may result in fire, repair, you can return it to your dealer. You can also return electric shock, or other hazards.
C41. · Electronic Input Switching 3. A McIntosh Power Controller may be added to the C41 to Digital Logic integrated circuits drive Electromagnetic provide AC Power Switching to components that do not have Power Control Connections.
Introduction, Performance Features and Dimensions C41 Dimensions The following dimensions can assist in determining the best location for your C41. There is additional information on the next page pertaining to installing the C41 into cabi- nets. " 44.45cm " 6"...
Installation Installation The C41 can be placed upright on a table or shelf, standing 1 inch (2.54 cm) in front of the mounting panel for knob on its four 1 inch high feet. The four feet may be removed clearance. Be sure to cut out a ventilation hole in the from the bottom of the C41 when it is custom installed as mounting shelf according to the dimensions in the drawing.
C41 Rear Panel Connections and Switch Connect the C41 POWER CONTROL DATA PORTs send CD1 balanced INPUTS power cord to a live MAIN Output sends a signals to compatible accept high level program AC outlet. Refer to turn-on signal to a...
Source Component. PROCESSOR jacks in a similar manner. 8. Connect a Data cable from the C41 CD DATA PORT to 3. Connect cables from the C41 CD INPUTS to the out- the DATA IN of a McIntosh D/A Converter and CD puts of a McIntosh D/A Converter and CD Transport.
Note: A Third Power Amplifier may be connected to the Listen 2 OUTPUTS for an additional room. 2. Connect a Power Control cable from the C41 POWER CONTROL 1 jack to the POWER CONTROL IN of a McIntosh power amplifier.
How to Connect for Video Switching How to Connect for Video Switching 1. Connect a Data cable from the C41 VIDEO and T3/ DVD DATA PORTS, using a Y Adapter, to the Monitor/TV MVS-3 DATA IN jack. 2. Connect a Power Control cable from the C41 ACC POWER CONTROL jack to the Power Control In of a McIntosh DVD/CD player.
C41 Front Panel Controls, Push-Buttons and Switch BASS control provides TREBLE control provides The BALANCE control VOLUME control 12dB boost or cut with 12dB boost or cut with a adjusts the relative vol- adjusts the volume a flat center position...
Adjust the BALANCE control as needed to achieve ap- proximately equal listening volume levels in each loud- Note: The C41 RECORD OUTPUTS are not affected by the speaker. Turn the BALANCE to the Left to emphasize the VOLUME or BALANCE controls. To listen to a different left channel by reducing the level of the right channel.
Page 13
This processor will affect only the RECORD signals sent to tape recorders. Reset of Microprocessors In the event that the controls of the C41 stop functioning, there is a built-in user reset function. Press the POWER switch to the OFF position, wait for two minutes. Then...
Remote Control Push-Buttons Turns AC Power ON or OFF to certain McIntosh Components when connected via the Data Port Press to Power the C41 Selects Functions for ON or OFF McIntosh Home Control- ler and as a shift key when used with the AM...
Downqpush-button to move from station to station. Press controlled by the C41 with the addition of a McIntosh Re- and hold a Channel Upp or Downq push-button to move mote Control Translator (RCT).
Frequency Response (Decibel) Hz (Hertz) Loudness Compensation Range (Decibel) Hz (Hertz) Note: The Loudness Compensation Range is a combination of the Loudness Circuitry and the Volume Controls rotational position. When the Loudness Circuit is active, the first 50% rotation of the Volume Control achieves maximum loudness compensation, as shown on the upper curve.
Signal To Noise Ratio 240 Volts, 50/60Hz at 20 watts. Phono, 90dB below a 10mV input, (84db IHF) NOTE: Refer to the rear panel of the C41 for the correct High Level, 103dB below rated output, (93db IHF) voltage. Maximum Voltage Output...
If a shipping 034037 Inner carton pad carton or any of the interior part(s) are needed, please call or write Customer Service Department of McIntosh Labo- 017218 Plastic foot ratory. Please see the Parts List for the correct part num- 100159 #10-32 x 3/4...
Page 20
McIntosh Laboratory, Inc. 2 Chambers Street Binghamton, NY 13903 McIntosh Part No. 04068302...
Need help?
Do you have a question about the C41 and is the answer not in the manual?
Questions and answers