Table of Contents
Advertisement
13. Always leave the housing slightly open when transporting by air or traveling through large
altitude changes. A piece of paper can be installed between the front and back doors of the
housing in order to prevent the housing from completely closing during the flight or altitude
changes.
14. Never dive with the Fantasea FG7X II Housing to a depth greater than 60 meters/200 feet.
15. It is important to test the integrity of the watertight seal prior to diving. This can be
accomplished by securely closing the back of the housing without the camera inside and then
submerging the housing into a bucket or sink filled with water. It is highly recommended that
the best method for ensuring that the seal is functioning properly is to carry the housing,
without the camera inside, on a dive. Carrying the empty housing on a dive will better ensure
that the watertight seal is properly functioning under the additional pressures associated with
diving.
16. It is likewise recommended to visually monitor the housing during every descent, especially for
the first 10 meters/33 feet. If water is observed entering the housing or bubbles escaping from
it, the housing should be rotated to a port down position and held in that manner as you make
a safe ascent and exit the water.
FANTASEA PRODUCT CONSUMER LIMITED WARRANTY
"Fantasea" warrants this Fantasea Line branded product against defects in materials and workmanship under
reasonable use for a period of ONE (1) YEAR, (two years, where required by law as determined by the origin of the
authorized dealer). This warranty is effective from the date of retail purchase from Fantasea or an authorized
Fantasea dealer, by the original end-user purchaser ("Warranty Period"). This warranty does not cover any
commercial use of the product. If a product defect arises and a valid claim is received within the Warranty Period, at
its option, Fantasea, or its authorized service facilities will either (1) repair the product defect at no charge, (2)
exchange the product with a product that is new or which has been manufactured from new or serviceable used
parts and is at least functionally equivalent to the original product. The warranty will not extend beyond the original
warranty period. Your Fantasea Product should be registered within 30 days of purchase. You must keep the proof of
purchase that indicates the date on which the purchase was made; as you may be required to show proof of purchase
if you need warranty service. The following conditions apply: 1. This warranty extends to the original purchaser only.
It is not assignable or transferable. 2. The warranty does not cover damage resulting from misuse, abuse, negligence,
or accidents. Proper maintenance of the Product is the responsibility of the owner. 3. The warranty does not cover
damage directly or indirectly resulting from the use of unauthorized replacement parts or service performed by
unauthorized facilities. 4. This warranty does not cover any damage to any other product used in conjunction with
the Fantasea product, including cameras and lenses, and resulting from any defect in the product materials or
workmanship. 5. The cost of sending the product back to Fantasea or its authorized service facilities is the
responsibility of the customer. 6. The warranty does not cover any incidental damages resulting from any defects in
the product. This expressly includes any travel reimbursements or any other costs associated with the purchaser's
optional use of the product. The conditions of this warranty are expressly in lieu of all other expressed warranties,
29
FG7X II Housing Instruction Manual 20160808
including the payment of consequential or incidental damages for the breach of any warranty. Please register your
product on line at this URL: http://www.fantasea.com/registration.
FANTASEA MOISTURE SENSOR AND ALARM
Never soak or wash the interior of the housing with any liquid. This will
activate the alarm in a manner that cannot be disabled, eventually causing
Note!
irreparable damage to the unit's electronics!
The Moisture Sensor and Alarm are a bonus add-on component and not an
integral part of the housing. Accordingly, it is not part of the housing
warranty coverage. The moisture detector has no warranty coverage.
The Moisture Alarm is installed inside the housing, opposite the Latch
Dial (Image #26 – item A). The Moisture Sensor is on the interior
bottom of the housing (Image #26 – item B). A thin wire connects
these units. Moisture sensors are very sensitive, so whenever moisture
is detected by the Sensor, the Moisture Alarm LED flashes and a
warning alarm beeps thus alerting the user of a possible leak.
IDENTIFICATION OF PARTS OF THE SENSOR AND ALARM
Electrical wires
Black tape wrap Sound
Alarm
Electrical plug
Cylinder
Wrapped Alarm Unit
Red LED light
A
B
Image #26
Battery
compartment
Battery removal
3 V Lithium
Unw rapped Alarm Unit
groove
#CR1220 Battery
(
included
Moisture Sensor Unit
Sensor
30
FG7X II Housing Instruction Manual 20160808
)
Advertisement
Table of Contents
