Operation; Snow Blower Safety - Honda HSS724A Owner's Manual

Never use stale or contaminated gasoline or an oil and gasoline
mixture. Avoid getting dirt or water in the fuel tank.

Gasoline is highly flammable and explosive. You can be
burned or seriously injured when handling fuel.
• Stop the engine and let it cool before refueling
• Keep heat, sparks, and flame away
• Refuel only outdoors
• Wipe up spills immediately
If your equipment will be used on an infrequent basis, refer to the fuel
section of "STORAGE" on page 18
regarding fuel deterioration.
Refuel in a well-ventilated area before starting the engine. If the
engine has been running, allow it to cool. Refuel carefully to avoid
spilling fuel. Add fuel only while standing on the fuel tank side of the
snow blower. Do not fill the fuel tank completely. Fill tank to
approximately 1.4 inch (35 mm) below the top of the fuel tank to allow
for fuel expansion. After refueling, tighten the fuel tank cap securely.
Never refuel the snow blower inside a building where gasoline fumes
may reach flames or sparks. Keep gasoline away from appliance pilot
lights, barbecues, electric appliances, and power tools.
Spilled fuel is not only a fire hazard, it causes environmental damage.
Wipe up spills immediately.
With the engine stopped:
1. Remove the fuel tank cap and check the fuel level.
2. Refill the tank if the fuel level is low. Do not fill above the base of
the filler neck.
FUEL TANK CAP
FUEL GAUGE
FUEL INLET
NOTICE
Fuel can damage paint and plastic. Be careful not to spill fuel when
filling your fuel tank. Damage caused by spilled fuel is not covered
under warranty.
6
WARNING
for additional information
FUEL TANK TOP
1.4 inch
(35 mm)
MAXIMUM
FUEL LEVEL

OPERATION

Before operating the snow blower for the first time, review both "FOR
YOUR SAFETY" on page 2
page 5.
Even if you have operated other snow blowers, take time to become
familiar with how this snow blower works, and practice in a safe area
until you build up your skills.
Never tamper with or alter any of the controls or safety devices on the
snow blower. Tampering is a violation of federal and California law.
For your safety, do not start or operate the engine in an enclosed area
such as a garage. Your snow blower's exhaust contains poisonous
carbon monoxide gas that can collect rapidly in an enclosed area and
cause illness or death.

Exhaust contains poisonous carbon monoxide gas that
can build up to dangerous levels in closed areas.
Breathing carbon monoxide can cause
unconsciousness or death.
Never run the engine in a closed, or even partly closed
area where people may be present.

Snow Blower Safety

Honda snow blowers are designed to clear snow from driveways and
walkways. Other uses can result in injury to the operator or damage to
the snow blower and other property.
Most injuries or property damage with snow blowers can be prevented
if you follow all instructions in this manual and on the snow blower.
The most common hazards are discussed below, along with the best
way to protect yourself and others.
Avoid Rotating Impeller and Auger
Hand contact with the rotating impeller inside the discharge chute is
the most common cause of injury associated with snow blowers. The
snow blower auger can also cause serious injury. Keep away from the
impeller and auger whenever the engine is running. If you need to
work around the snow blower to clear snow for any reason, always
shut off the engine. If the snow discharge chute becomes clogged,
stop the engine and disconnect the spark plug cap. Use the snow
clearing bar to remove the obstructions. Never put your hand into the
snow discharge chute while the engine is running; serious personal
injury could result.
Clear Operation Area
The snow blower can throw rocks and other objects with enough force
to cause serious injury. Before operating the snow blower, carefully
inspect the area and remove any visible stones, sticks, newspapers,
nails, pieces of wire, and other loose objects. Never use the snow
blower to clear snow from a gravel road or driveway, as rocks may be
picked up and ejected. They may cause injury to bystanders.
Keep Shields in Place
Guards and shields are designed to protect you from being hit by
thrown objects and to keep you from touching hot engine parts and
moving components. For your safety and the safety of others, keep all
shields in place when the engine is running.
and "BEFORE EACH OPERATION" on
WARNING