MTS Systems Level Plus Interface Manual
Magnetostrictive liquid level transmitters with temposonics technology
Hide thumbs
Also See for Level Plus:
- Operation and installation manual (85 pages) ,
- Operation and installation manual (115 pages)
Related Manuals for MTS Systems Level Plus
Summary of Contents for MTS Systems Level Plus
- Page 1 Level Plus ® Magnetostrictive Liquid Level Transmitters with Temposonics Technology ® HART Interface Manual ® LP Series...
-
Page 2: Table Of Contents
® HART Interface Manual LP Series Table of contents 1. Contact information ..............3 2. Terms and definitions ..............4 3. Introduction .................6 4. Safety instructions ..............6 5. Quick start-up guide ..............6 5.1 Before you begin ..............6 5.2 Quick start-up procedure ............6 6. -
Page 3: Contact Information
Mailing and shipping address Mailing and shipping address MTS Systems Corporation MTS Sensors Technology Corporation Sensors Division 737 Aihara-machi, Machida-shi 3001 Sheldon Drive Tokyo 194-0211, Japan Cary, North Carolina, 27513, USA Technical support and applications Customer service Tel.: +81-42-775-3838... -
Page 4: Terms And Definitions
® HART Interface Manual LP Series FOUNDATION™ fieldbus 2. Terms and definitions An all digital, serial, two-way communications system that serves as the base-level network in a plant or factory automation environment. Developed and administered by the fieldbus FOUNDATION™. 6A Heavy Oils ‘Generalized Crude Oils’, Correction of Volume to 60 °F against API Gravity. - Page 5 ® HART Interface Manual LP Series Strap Table A table of measurement correlating the height of a vessel to the volume Mass that is contained at that height. The transmitter can contain up to 100 The property of a body that causes it to have weight in a gravitational points.
-
Page 6: Introduction
® HART Interface Manual LP Series Turn off power and disconnect power supply and current meter. 3. Introduction Install in tank. 3.1 Purpose and use of this manual 6. Display Menu Before starting the operation of the equipment read this documentation thoroughly and follow the safety information. -
Page 7: Display Diagram
® HART Interface Manual LP Series 6.2 Display Diagram ` Int Current LRV ` Int Current URV ƒ Alarm Select ƒ Signal Strength ` Prod Trig Lvl ` Int Trig Lvl • Calibrate ƒ Product Level ` Current Level ` Offset ƒ... -
Page 8: Error Codes (Faults)
® HART Interface Manual LP Series 8. Error Codes (Faults) Fault Description Corrective Action Fault Description Corrective Action Code Code Missing • Verify Float Configuration is correct for the DAC Fault 4 Cycle power to sensor. If proper operation Magnet number of floats installed is not restored, Contact Factory •... -
Page 9: General Parameters
® HART Interface Manual LP Series Connect level transmitter to HART ® to USB converter, connect 24 Vdc power to the level transmitter, and connect the HART ® USB converter to the PC. Example setup shown below. Note: ® Power must be on Loop 1 for HART communication to work. -
Page 10: Process Data
® HART Interface Manual LP Series 9.1.3 Process Data 9.1.4.2 Calibrate Fig. 4 Process data window Fig. 6 Calibrate window The Process Data section of the setup software allows the user to view Calibrate allows the user to change the set points for levels and tempe- the current output of the level transmitter in the engineering units and log rature. -
Page 11: Calibrate
® HART Interface Manual LP Series float (Prod Trig Lvl) and the Interface float (Int Trig Lvl). If the Interface Float Config float is not active no signal can be viewed. Allows the user to enable or disable the product float (Loop 1) and/or the interface float (Loop 2). - Page 12 Document Part Number: 551699 Revision A (EN) 10/2016 GERMANY MTS, Temposonics and Level Plus are registered trademarks of MTS Systems Corporation MTS Systems Corporation MTS Sensor Technologie in the United States; MTS SENSORS and the MTS SENSORS logo are trademarks of MTS Sensors Division GmbH &...