PREFACE Thank you for buying the Forest Master FM13SG Stump Grinder, another high-quality machine from our company. To get the most out of your purchase, please read this manual before using the stump grinder. We ask you to please read this manual carefully beforehand in order to familiarise yourself with this product and after reading, please store this instructional manual for future reference.
• Make sure that all shields and guards are in place and are in good condition prior to operating the machine. Check cutting wheel for damage or missing teeth and replace as necessary. Stump Grinder FM13SG...
• Do not attempt to start the engine if fuel is spilled. Wipe away the spillage and ensure all fuel has dried before starting the machine. • Always make sure the fuel cap is securely tightened and replace before starting. • If the fuel tank needs to be drained, it should be done outdoors. Stump Grinder FM13SG...
The next step causes the cutter wheel to rotate, keep everyone away. 7. Move the throttle to fast. if the engine is cold, allow the engine to idle(throttle set to slow) for a few minutes before cutting. Stump Grinder FM13SG...
It is also possible to use the cutter wheel to push chips off to the side. • In order to prevent any of the wheels becoming stuck in the hole. Move the grinder to the other side of the stump to continue removal or by filling the hole with chips before continuing. Stump Grinder FM13SG...
Page 8
3. Raise and lower the cutter wheel between sweeps by lowering and raising the control handle. 4. Roll the machine forward and back, by pushing and pulling on the control handle. To do this, release the brake. Relock it when the machine has been repositioned and continue cutting. Stump Grinder FM13SG...
1. Immediately push the emergency (on/off ) switch for the engine will be shut off. 2. Be sure to allow all moving parts to come to a complete stop. 3. Pull the brake lever to engage the brake. 4. Rectify the emergency situation and return to normal operation. Stump Grinder FM13SG...
There are legal road requirements for towing equipment and trailers (such as lighting and licensing), it is the owner's responsibility to be aware of these laws and to adhere to them. Stump Grinder FM13SG...
The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional. Some illustrations may not be applicable to your machine. Stump Grinder FM13SG...
M 12 self-lock nut Shor t axle sleeve B lade adapter Str aight blade R ight blade L eft blade B lade clamp plate L ong axle sleeve M 10 self-lock nut M 10*45 inner hex bolt(8.8) Stump Grinder FM13SG...
R E F.NO. DES CR I PT I ON H andle connector handr ail A 17 M12* 25 inner hex bolt T hrottle A 18 M12* 65 inner hex bolt E mergency stop switch E mergency stall switch Stump Grinder FM13SG...
Page 16
B ra ke clamp plate(outer) I nner bra ke clamp plate B ra ke pin A 19 M8*4 5 inner hex bolt B ra ke connect plate A 20 7 jump r ing I nner spacer A 21 M8 self-lock nut Stump Grinder FM13SG...
B r ake assembly B elt wheel M 10*20 hex bolt B elt cover fitting rod A 13 M 8*20 inner hex bolt V-belt A 16 M 8*25 hex bolt B elt (outer) cover A 21 M 8 self-lock nut Stump Grinder FM13SG...
Page 19
M 10*45 hex bol t ( engi ne) M 10*80 hex bol t 16 f l at gas ket M 8*20 hex bol t M 14*1. 5 s el f - l ock nut 28*T2 f l at gas ket Stump Grinder FM13SG...
Need help?
Do you have a question about the FM13SG and is the answer not in the manual?
Questions and answers