Waterco R120 Installation - Operation - Warranty Manual

Robotic pool scrubber clean

Hide thumbs

Table Of Contents

Table of Contents

Quick Links

Download this manual

120

RobotIc PooL ScRUbbER cLEaNER

Installation - operation - Warranty Manual

This equipment is to be installed and serviced by a qualified technician. Improper installation may result in

property damage, serious injury or death. Improper installation and/or operation will void the warranty.

WaRNING

Notice to Installer

This manual contains important information about the installation, operation & safe use of this product.

Once the product has been sold or installed this manual must be given to the owner/operator of this equipmen

www.waterco.com

Table of Contents

Need help?

Do you have a question about the R120 and is the answer not in the manual?

Questions and answers

Summary of Contents for Waterco R120

Page 1 Improper installation and/or operation will void the warranty. WaRNING Notice to Installer This manual contains important information about the installation, operation & safe use of this product. Once the product has been sold or installed this manual must be given to the owner/operator of this equipmen www.waterco.com...
Page 2: Table Of Contents
Cleaner available. We are sure you will find your new R120 a pleasure to use. Before you use the cleaner, we recommend that you read through the relevant sections of this manual, which provides a description of your cleaner and its functions.
Page 3: General Instructions
Disconnect the power supply supply from the outlet when not in use. DO NOT switch the R120 to “ON” if it is not immersed in water. Operating the cleaner out of water may cause severe damage & will result in loss of warranty. Always remember to turn the power supply “OFF” and unplug it from the power outlet before removing the...
Page 4: Installation
The cleaner will sink to the bottom of the pool. Place a sufficient length of the power cord into the water that will enable the R120 to easily reach all areas of the pool. (Do not place ALL of the power cord into the pool unless required).
Page 5: Removing Cleaner From Pool
The R120 may also climb the pool wall, scrub to the waterline, turn the pump motor off, and float away from the pool wall down to the bottom of the pool.
Page 6 Once the R120’s bottom lid is seated press it firmly into the cleaner, the two red side tabs should click into place and turn the front and rear red retaining clips as indicated by the directional arrows into the locked position, refer Figure 9. Gently pull on the cleaner bottom lid to insure that it is properly locked in.
Page 7: Power Cord Maintenance
R120 Power Kink Resistant cord advantage The R120 Robotic Pool Cleaner has a specifically designed power kink resistant cord using a one piece extruded technology that prevents the cord from delaminating, protecting the internal wires from shorting out and extending it’s operating life.
Page 8: Storing The Power Cord
The warranty obligations of Waterco Ltd shall be limited to repair or replacement of the product or any defective component, at the discretion of Waterco Ltd. The repair or replacement may include the use of refurbished components and/or units. Waterco Ltd will not be liable or responsible under any circumstances or in any amount for any consequential or incidental damages, for any injury or damages to persons or property using or used in connection with this product, or for loss of profits or other costs or expenses of any kind or character.
Page 9 WaRRaNtY coVER If a defect occurs in any Waterco product during the warranty period, Waterco will at its discretion, repair the product or replace and install the defective part, free of charge provided that the defect results solely from poor workmanship or materials and subject to these terms and conditions.
Page 10 To the extent permitted by law Waterco excludes all liability it may have to the purchaser for indirect, special or consequential loss arising from or related to any defect in any Waterco product, or any act or omission, including negligence of Waterco, including, but not limited to, loss of business, loss of profit, loss of revenue, lost opportunity, inconvenience, and damage to any property other than the Waterco product.
Page 11 Most pool cleaner problems are caused by incorrect installation, poor water chemistry and wear and tear. Please regularly check the condition of the R120 filter bag, bottom lid, brushes and tracks, as these are like the tyres on a car & need replacement from time to time.
Page 12: Trouble Shooting
Symptom Possible Reasons cleaner Dead in water/Will not Restart Is time being allowed for the unit to reset? At least 1 minute is needed between cycles to reset the power supply. Is the outlet working? Earth Leakage Circuit Breaker or breaker may have tripped Is an extension cord being used? Extension cord may be defective cleaner not Moving...
Page 13 Potential Solution Turn power supply off and allow 30 seconds for cleaner to reset. Check Earth Leakage Circuit Breaker or breaker and try a different outlet. Try running the cleaner without an extension cord. Using a Electrical Extension cord is not recommended. Check for debris and remove if found.
Page 14: Notes
NotES...
Page 15 NotES...
Page 16 Singapore 079314 47000 Sungai Buloh, Kent, ME9 9PS, UK 69800 SAINT PRIEST tel: + 44 1795 521733 tel: + 33 4 72 79 33 30 tel: + 65 6344 2378 Selangor Darul Ehsan tel: + 60 3 6145 6000 www.waterco.com...