Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TREND VJS/AG/36
Summary of Contents for TREND VJS/AG/36
- Page 1 VJS/AG/36 VARIJIG VARIABLE ANGLE GUIDE 36” (915mm)
-
Page 2: Table Of Contents
VJS/AG/36 Dear Customer TECHNICAL DATA Thank you for purchasing this Trend product, we Extension thickness 15.8mm hope you enjoy many years of creative and Extension width 54.0mm productive use. Working length at 90º: Router 915mm* Please remember to return your guarantee card Circular Saw 780mm** within 28 days of purchase. -
Page 3: Safety
VJS/AG/36 SAFETY and balance at all times. Do not use recommended when working awkward or uncomfortable hand outdoors. Wear protective hair WARNING: positions. covering to contain long hair. Observe the safety regulations in the 17. Don’t abuse the cable. Never carry 5. - Page 4 15. All fastening screws and nuts should be adhered to. Recommended speeds ensure there is sufficient clearance be tightened using the appropriate are shown in the Trend Routing between cutter tip and inside edge of spanner or key and to the torque Catalogue and/or website.
-
Page 5: Items Enclosed
VJS/AG/36 ITEMS ENCLOSED (fitted to protractor) ITEMS REQUIRED s Plunge router (or jigsaw/circular saw). s Clamps x 3. s Hand tools. -
Page 6: Description Of Parts
VJS/AG/36 DESCRIPTION OF PARTS Alloy extrusion 42” with scale and Plastic washer end caps T-nut Main body with protractor plate Knurled locking knob and scale Adjustable locking lever (female) Bottom rail M Adjustable locking lever plastic washer Zero scale plate... -
Page 7: Assembly & Adjustment
VJS/AG/36 ASSEMBLY & ADJUSTMENT s Fit the alloy connector to the alloy extrusion The angle guide requires assembly before use, by locating the two holes of the alloy please use the drawing on page 5 as a guide. connector with the two T-nuts in the alloy s Remove knurled locking knob and place in extrusion. -
Page 8: Adjusting Guide Angle
VJS/AG/36 s Loosen the adjustable locking lever, and Preset Angles place the knurled locking knob at the 90° s When using a preset angle, position the position in the protractor, and tighten down. extrusion and protractor at the required angle This locks the protractor in position. -
Page 9: Operation
VJS/AG/36 Marking Out for the Cut Line OPERATION To set the angle guide to a cut line marked on The angle guide must have a lead-in and lead- the material, measure the distance from the out of the component to ensure the router or saw blade or cutter edge to the base edge of the saw base plate is always guided. -
Page 10: Clamping
The material being cut will need to extrusion are held safely. supported and clamped securely. ACCESSORIES Only use original Trend accessories: Routing or Sawing using the Two types of friction clamp are available. They Angle Guide can be used with the guide between 30º to 150º. -
Page 11: Maintenance
VJS/AG/36 MAINTENANCE This accessory has been designed to operate over a long period of time with minimum of maintenance. Continual satisfactory operation depends upon proper tool care and regular cleaning. Cleaning s Keep the grooves on the extrusion and knob threads clear of sawdust. -
Page 12: Spare Parts - Spare Parts List
VJS/AG/36 VJS/AG/36 - SPARE PARTS DIAGRAM v1.0 01/2010 Item Qty. Desc. Ref. Extrusion 1070mm WP-VJS/07C Main Body with Protractor Plate and Scale WP-VJS/AG/01 Bottom Rail WP-VJS/AG/02 Zero Scale Plate WP-VJS/AG/03 Alloy Connector WP-VJS/AG/04 Knob Male UNC1/4-20 x 3/8” WP-VJS/AG/05 Knob Female UNC1/4-20... -
Page 13: Spare Parts Diagram
VJS/AG/36 VJS/AG/36 - SPARE PARTS DIAGRAM V1.0 01/2010 -12-... - Page 14 RECYCLABLE © Copyright Trend 2010. No part of this publication may be reproduced, stored or transmitted in any form without prior permission. Our policy of continuous improvement means that specifications may change without notice. Trend Machinery and Cutting Tools...
Need help?
Do you have a question about the VJS/AG/36 and is the answer not in the manual?
Questions and answers