Rear View; Specifications - Crest Audio Pro 10001 Specification Sheet

2Ω Stereo Power
1Ω Stereo Power
4Ω Bridged Mono Power
2Ω Bridged Mono Power
Max RMS Output Voltage
(each channel)
Peak Output Voltage
(each channel)
Frequency Response
(+0 / -0.3dB, 1W/8Ω)
Power Bandwidth
(rated power at 4Ω, 1% THD+N)
Protection Circuitry
THD+N
(rated power at 4Ω, 1kHz)
SMPTE IMD
(rated power at 8Ω, 60Hz & 7kHz)
Damping Factor
(10-400Hz at 8Ω)
Input CMRR
Input Sensitivity
(rated power at 4Ω )
Voltage Gain
Input Impedance
Hum and Noise
("A" weighted, full power, 4Ω)
Crosstalk
("A" weighted, full power, 4Ω)
Input Connectors
Output Connectors
Filter Storage
Power Supply
(factory configured)
Idle Current Draw
1/8 Power Curr. Draw
(typical music, 120V/4Ω)
1/3 Power Curr. Draw
(continuous music, 120V/4Ω)
Max Curr. Draw
(circuit breaker rating, 120V/4Ω)
Thermal Emissions
(1/8 Power, 4Ω)
Thermal Emissions
(1/3 Power, 4Ω)
LED Indicators
Construction
Dimensions
(Height x Width x Depth)
Gross Weight, Net Weight
† USA, Canada, U.K., and many other countries. Power figures are watts per channel, both channels driven. Crest Audio reserves the
right to make improvements in manufacturing or design which may affect specifications. Crest Audio specification literature is available
in downloadable PDF file format; visit our website at http://www.crestaudio.com. ©1997 Crest Audio Inc. 5/21/97

Rear View

OUT B
- +
AC MAINS-INPUT
v. 2.4 10/15/97 B5000010
1 0 0 0 1 P OW E R A M P L I F I E R
S P E C I F I C AT I O N S
20Hz-20kHz, <0.1% THD+N
3500W
5000W
7000W
10,000W
105V
150V
20 Hz-20 kHz, -3dB @ 53kHz
20 Hz-20 kHz, +0/-0.2 dB
Clip Limit, IGM, AutoRamp, High Temp, short-circuit,
DC voltage, turn-on/off transient, sub/ultrasonic input.
<0.02%
0.05%
580:1
>60 dB
(1kHz)
2.24V RMS
X40
>20kΩ
(balanced)
> -100 dB
> -60dB
Class H
Female XLR Input (pin 3+), Octal Socket
(per channel)
Single screw solderless copper output lugs.
(per channel)
29,200 µF
100V-240V, 50-60Hz
2.0A per line cord
(120V)
13.0A per line cord
25.0A per line cord
35.6A per line cord
4450 BTU/hr
7908 BTU/hr
Cooling Rear to front tunnel, variable speed DC fan, 235 CFM max.
Controls Front panel: 2 attenuators, circuit breaker/power switch; Rear
panel: mode switch, signal ground lift jumper.
Clip/Limit, Signal, Temp/DC, Active
(per channel)
12 ga. steel chassis, 0.075" (1.9mm) aluminum front panel
7" x 19" x 20.5" (19.5" to end of rear ears), 178mm x 483mm x
521mm (496mm to back of rear ears)
145 lbs (65.83 kg.), 137 lbs (62.20 kg.)
Warranty 5 years, parts and labor†
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
AVIS : RISQUE DE CHOC ÉLECTRIQUE—NE PAS OUVRIR
WARNING TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK DO NOT
EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE.
ATTENTION! POUR ÉVITER LE RISQUE D'INCENDIE OU DE CHOC
ÉLECTRIQUE, NE PLACEZ PAS CET APPAREIL SOUS LA PLUIE OU Á
L'HUMIDITÉ
Designed & manufactured in the USA by:
Crest Audio Inc.
100 Eisenhower Dr.
Paramus, New Jersey 07652 USA
CH. B
*B5000010*
Architect's & Engineer's Specifications
The power amplifier shall consist of 2 channels and deliver
Typical Music Prog. Material
a minimum of 3500 watts at 2 ohms, 5000 watts at 1 ohms;
5000W
per channel, both channels driven, 20Hz-20kHz, <0.1%
7500W
THD+N. In bridged mode, it shall deliver a minimum of
10,000W
7000 watts at 4 ohms, and a minimum of 10,000 watts at 2
15,000W
ohms, 20 Hz-20kHz, <0.1% THD+N.
The amplifier shall be rear-to-front tunnel-cooled, with a
variable-speed DC fan.
The amplifier shall have circuitry to protect itself and the
speaker load from output short circuits, DC voltage on out-
puts, and thermal overload. It shall have RMS clip limiting
and impedance sensing circuitry. Output relays shall pro-
tect the speakers from any type of amplifier failure.
In stereo or parallel operation, the amplifier shall have a
voltage gain of X40 with an input sensitivity of 2.23V for
rated power at 4 ohms. The hum and noise level shall be
greater than 100 dB below rated output, "A" weighted.
Intermodulation distortion shall be less than 0.02% from
250 milliwatts to full rated power. The amplifier shall have
a class H output stage with a modulated power supply. The
frequency response shall be greater than 20Hz-20kHz, +0,
-.3dB (1W/8Ω).
The amplifier shall operate at either 100, 120, 220, or 240
volts, 50-60 Hz AC (configured at factory). Maximum cur-
rent draw at 120V shall be no greater than 35.6A per line
cord, both channels driven continuously into 2 ohm resis-
tance.
The amplifier front panel shall include Active, Temp/DC,
Signal Present and Clip/Limit LED indicators for each
channel, two combination power switch/magnetic circuit
breakers and recessed and detented gain pots.
Rear panel input connectors shall be XLR type, one female
per channel. Output connectors shall be single screw sol-
derless copper lug type, two per channel. A signal/ground
lift jumper shall be provided.
The amplifier shall have two (2) three-conductor AC power
cords.
The packaging of the amplifier shall allow for standard
rack mounting without requiring space between similar
units. Dimensions shall be 19" (483mm) wide, 7" (178mm)
high and 20.5"(521mm) deep. It shall weigh 137lbs.
(62.20kg) net. The amplifier shall be designated the Crest
Audio Model 10001.
PARALLEL
A
PUSH IN
PIN 3+
OUT A
+ -
SIGNAL
GROUND
LIFT
STEREO
BRIDGE
B
PUSH IN
NEXSYS
OUTPUT
SAMPLE
AC MAINS-INPUT
CH. A
100 Eisenhower Dr., Paramus NJ 07652 USA
: 201.909.8700
TEL
http://www.crestaudio.com
Crest Audio Inc.
: 201.909.8744
FAX
Printed in USA