Vox WAFER-5820 User Manual
  1. Manuals
  2. Brands
  3. Vox Manuals
  4. Motherboard
  5. WAFER-5820
  6. User manual
Vox WAFER-5820 User Manual

Vox WAFER-5820 User Manual

Low power gxlv-233 mmx with svga/lcd, ethernet, & audio sbc
Hide thumbs
Table of Contents

Advertisement

Quick Links

Enlarged version
WAFER-5820
Low Power GXLV-233 MMX
with SVGA/LCD,
Ethernet, & Audio SBC.
Copyright Notice
© Copyright 2000. All Rights Reserved. Manual first edition Apr..01, 2000.
The information in this document is subject to change without prior notice in order to
improve reliability, design and function and does not represent a commitment on the part
of the manufacturer.
In no event will the manufacturer be liable for direct, indirect, special, incidental, or
consequential damages arising out of the use or inability to use the product or
documentation, even if advised of the possibility of such damages.
This document contains proprietary information protected by copyright. All rights are
reserved. No part of this manual may be reproduced by any mechanical, electronic, or
other means in any form without prior written permission of the manufacturer.
Trademarks
WAFER-5820 is a registered trademark. IBM PC is a registered
trademark of International Business Machines Corporation. Intel is a registered
trademark of Intel Corporation. Other product names mentioned herein are used for
identification purposes only and may be trademarks and/or registered trademarks of their
respective companies
Contents
1.Introduction......................................................................... 4
2.Installation........................................................................... 7
3.Connection ........................................................................ 12
2

Advertisement

Table of Contents
loading

Related Manuals for Vox WAFER-5820

Summary of Contents for Vox WAFER-5820

  • Page 1: Table Of Contents

    3.7 USB Port Connector CN5 Trademarks 3.8 IrDA Infrared Interface Port (CN11) WAFER-5820 is a registered trademark. IBM PC is a registered 3.9 VGA Connector (CN4) trademark of International Business Machines Corporation. Intel is a registered trademark of Intel Corporation. Other product names mentioned herein are used for 3.10 LCD/LVDS Interface Connector...

  • Page 2: Introduction

    4.5 Power Management Setup AT-compatible industrial computer on a single board. The 4.6 PNP / PCI CONFIGURATION WAFER-5820 is equipped with a low-power consumption and high 4.7 LOAD BIOS DEFAULTS performance GXLV-233 processor on board. It also contains an SDRAM SODIMM socket that can support up to 128MB memory.

  • Page 3: Specifications

    1.1 Specifications *USB interface: two USB ports, USB 1.0 compliant *Power management: supports power saving modes *NS GXLV-233 MMX 32-Bit x86 Processor including Normal/Doze/Sleep modes. APM1.1 compliant Supports Intel MMX instruction set extension for the *Watch-dog timer: can be set by 1-255 seconds period. acceleration of multi media applications Reset or NMI was generated when CPU did not periodically 16 KB unified L1 cache...

  • Page 4: Installation

    Installation This chapter gives instructions about how to set up the CN15 WAFER-5820 hardware, including directions of setting jumpers and connecting peripherals, switches and indicators. Before installation, please pay attention to the unpacking precautions on CN16 CN17 the following page for safety.

  • Page 5: Unpacking Precautions

    Set back to normal operation mode, open JP9. Ground yourself to remove any static charge before touching the Wafer-5820 SBC. You can do it by using a grounded wrist • JP9: Clear CMOS Setup (Reserve Function)

  • Page 6: Lcd Vcc Voltage Selector

    The LCD interface connector CN15 can provide 5V or 3.3V power supply by selecting the JP1 to meet the different LCD 3.1 Floppy Disk Drive Connector (CN7) requirement. WAFER-5820 board is equipped with a 34-pin daisy-chain DESCRIPTION driver connector cable. CN7: FDC CONNECTOR 3.3V...

  • Page 7: Pci E-Ide Disk Drive Connector (Cn2)

    3.3 Parallel Port (CN1) For IDE HDD connection, The Wafer-5820 was designed with This port is usually connected to a printer, The WAFER-5820 one 2.0mm connector (CN2), which could be converted to two includes an on-board parallel port(CN1), accessed through a 2.54mm standard IDE connector via proprietary cable.

  • Page 8: Audio Connector

    • Note : TX2+,TX2- and RX2+,RX2- are for transmitting and CN8: Serial Port1 Connector (9-pin DSUB) receiving, respectively, in the RS-422 connection. While in PIN NO. DESCRIPTION RS-485 connection, TX2+,RX2+ and TX2-,RX2- must be DATA CARRIER DETECT (DCD) twisted each. Anyhow, you can only choose to use RECEIVE DATA (RXD) RS-232 or RS-422/485.

  • Page 9: Keyboard & Ps/2 Mouse Connector (Cn6)

    3.10 LCD/LVDS Interface Connector D1F+ USBVCC2 D2F- The WAFER-5820 provides a 2x22-pin connector for the LCD D2F+ flat panel interface and a 2x10-pin connector for the LVDS flat panel interface. The Wafer 5820 comes to support TFT LCD panels at 3.8 IrDA Infrared Interface Port (CN11)

  • Page 10: Lan Rj45 Connector

    P23 (R5) P10 (G0) TxOUT1A- TxCLKOUTA- P11 (G1) SHFCLK TxOUT1A+ TxCLKOUTA- P12 (G2) P13 (G3) P14 (G4) P15 (G5) P2 (B0) P3 (B1) SHFCLK 3.11 LAN RJ45 Connector ENABLK The WAFER-5820 built-in RJ45 LAN connector is for 10/100Mbps Ethernet (RTL8139B).

  • Page 11: Fan Connector (Fan1)

    GROUND VCC5V 3.14 PC/104 Connection Bus The WAFER-5820 PC/104 expansion bus let you attach any kind of PC/104 modules. The PC/104 bus has already become the industrial embedded PC bus standard, so you can easily install over thousands of PC/104 modules from hundreds of vendors in the world.

  • Page 12: Ethernet Led And Power/Hdd Leds

    • CN10: PC/104-64 Connector 3.15 Ethernet LED and Power/HDD LEDS PIN NO. Description PIN NO. Description D6:Ethernet LED setup IOCHCK# Setting IRSTDRV Green lamp Orange lamp IRQ9 D1:Power/HDD setup -12V Setting Green lamp Power +12V Orange lamp IOCHRDY SMEMW# LA19 SMEMR# LA18 IOW#...

  • Page 13: Getting Start

    AWARD BIOS Setup configuration. The main function is for Date/Time setting and Floppy/Hard Disk Drive setting. Please refer the following WAFER-5820 uses the AWARD PCI/ISA BIOS for system screen for this setup. configuration. The AWARD BIOS setup program is designed to...

  • Page 14: Bios Features Setup

    3. Manually enter the specifications by yourself from 4.4 Chipset Features Setup the ”User“ option. This setup function works mostly on board's chipset. This Note: option is used to change the chipset's configuration. Please, carefully change any default setting, otherwise the system will If you need more information on any particular field, just highlight it then press <F1>...

  • Page 15: Power Management Setup

    4.5 Power Management Setup 4.6 PNP / PCI CONFIGURATION Power Management Setup helps user to handle the This menu is used to assign certain IRQ to your PNP/PCI ROCKY-568SEV board‘s “green” function. This feature can devices manually. shut down the video display and hard disk to save energy, for example.

  • Page 16: Load Bios Defaults

    4.7 LOAD BIOS DEFAULTS 4.8 LOAD SETUP DEFAULTS If you select 'Y' to this field, the Setup Defaults will be loaded If you select 'Y' to this field, the BIOS Defaults will be loaded except Standard CMOS SETUP. The default settings are except Standard CMOS SETUP.

  • Page 17: Integrated Peripherals

    Audio High DMA Select -- DMA5, DMA6, DMA7, Disabled 4.9 INTEGRATED PERIPHERALS To select the high DMA channel. Multiple Monitor Support -- No Onboard, PCI first, M/B first To select the primary VGA for multiple monitor support in WINDOWS. Video Memory Size -- 1.5M, 2.5M, 4.0M To select the size of video memory.

  • Page 18: Ide Hdd Autodetection

    Quick Without Saving 4.11 IDE HDD AUTODETECTION Select this option if you want to exit the Setup without saving This option detects the parameters of an IDE hard disk drive the changes that you made. Just simply press <Enter> key (HDD sector, cylinder, head, etc) automatically and will put the and you will exit the BIOS SETUP without saving the changes.

  • Page 19: Svga Setup

    The description below is its specifications and features: 2. WinNT4.0 drivers in Wafer-5820CD\Nt40Vga\ 5.1.1 Chipset The WAFER-5820 uses a Cyrix CX5530 chipset as its 5.2 Further Information SVGA controller. It is compatible with many common 18-bit For more detailed information about the PCI/SVGA installation LCD displays and traditional analog CRT monitors.

  • Page 20: Audio

    PCI Bus Ethernet Interface 6.1 Introduction 7.1 Introduction With on-board audio interface, the WAFER-5820 can perform The WAFER-5820 provides a high performance 32-bit Ethernet high-quality stereo sound and FM music synthesis (ESFM) by chipset which is completely compliant with IEEE 802.3 100 Mbps using the CX5530 audio controller.

  • Page 21: Appendix A. Watch-Dog Timer

    periodically refreshed by reading the same I/O port 043/843H and Appendix A. Watch-Dog Timer 443H. This must be done within the time out period that is selected by software, please refer to the example program. The WatchDog Timer is a device to ensure that standalone A tolerance of at least 5% must be maintained to avoid unknown systems can always recover from catastrophic conditions that routines within the operating system (DOS), such as disk I/O that...

  • Page 22: Appendix B. I/O Address Map

    Appendix B. I/O Address Map ;;ADD YOUR APPLICATION HERE W_LOOP: B.1 System I/O Address Map MOV DX, TIMER_STOP I/O Address Map Description IN AL, DX 000-01F DMA Controller #1 020-021 Interrupt Controller # 1, Master MOV DX, TIMER_START 022-023 Chipset address 040-05F System Timer IN AL, DX.

  • Page 23: Data

    B.2 DMA channel assignments B.3 Interrupt assignments Channel Function Interrupt # Interrupt source Available Parity error detected Audio* IRQ 0 System timer Floppy disk (8-bit transfer) IRQ 1 Keyboard Parallel** IRQ 2 Interrupt from controller 2 (cascade) Cascade for DMA controller 1 IRQ 8 Real-time clock Audio*...

Table of Contents