Related Manuals for Marshall Electronics VS-547-3GSDI
Summary of Contents for Marshall Electronics VS-547-3GSDI
-
Page 1: User Manual
Marshall Electronics VS-547-3GSDI 2 Megapixel IP Box Camera X30 Zoom CMOS, 1080P @60fps User Manual Firmware Version v1.0 Copyright ©2016, Marshall Electronics, Inc. All Rights Reserved. This document may not be copied. - Page 2 Product options and specifications can be changed without notice. The information in this manual is furnished for informational use only and should not be construed as a commitment by Marshall Electronics, Inc. Marshall Electronics, Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication. Safety Precaution We appreciate your IP camera purchase.
-
Page 3: Table Of Contents
1. Introduction .......................... 4 1.1 About this Manual ......................4 1.2 Features ........................4 1.3 Product and Accessories ....................5 1.4 System Connections ..................... 6 2. Installation ..........................8 2.1 Connecting Power ......................8 2.2 Connecting Network ..................... 8 2.3 Connecting Video ......................8 2.4 Connecting Audio ...................... -
Page 4: Introduction
If an external sensor is activated, camera can be set to move to the corresponding preset position User Interface Diagnose and upgrade through dedicated program called VS Manager High Reliability Reliable Embedded System User Manual VS-547-3GSDI – V1.0 Page 4 of 74 3/2016... -
Page 5: Product And Accessories
1. Introduction 1.3 Products and Accessories Part Names and Functions Rear View User Manual VS-547-3GSDI – V1.0 Page 5 of 74 3/2016... -
Page 6: System Connections
Although up to 64 PCs or Decoders can be connected to one IP Camera, the maximum connections would be limited by network bandwidth connection. Functionally, the VMS (Video Management System) software provided can replace the decoder. User Manual VS-547-3GSDI – V1.0 Page 6 of 74 3/2016... - Page 7 VMS (Video Management System) is a Windows based remote monitoring program to access multiple servers for real-time monitoring or control of the servers and connected cameras. Please refer to the VMS User Manual for more information on VMS. User Manual VS-547-3GSDI – V1.0 Page 7 of 74 3/2016...
-
Page 8: Installation
2. Installation 2.1 Connecting Power After confirming the Power Source, connect Power Adaptor and connect the 12VDC Connector to the System. 2.2 Connecting Network Plug the Network Cable into the Ethernet port (RJ-45 network port). 2.3 Connecting Video 1) To display video through the composite or HD-SDI port, connect each port to a monitor using BNC coaxial cable. -
Page 9: Check If It Works
Please refer to the VS Manager manual for instructions on how to find the IP address of the camera and to make necessary changes. User Manual VS-547-3GSDI – V1.0 Page 9 of 74 3/2016... -
Page 10: System Operation
3. System Operation 3.1 Remote Video Monitoring There are two ways to monitor video when the VMS (Video Management System) and IP Camera are connected. In order for a proper operation, an IP Address must be set accordingly. Please refer to the VS Manager Manual enclosed with product for further details. - Page 11 Sensor Input. When the sensor of the camera is working, the sensor light turns red. Operate the Alarm Device by pressing the number icon. This camera supports One Alarm Output. A number icon indicates the status of the alarm device. User Manual VS-547-3GSDI – V1.0 Page 11 of 74 3/2016...
-
Page 12: Initialization Of Ip Address
3. Once the system reboots, IP Address will be set to the System Default as below: IP Mode IP Address 192.168.10.100 Fixed IP Subnet Mask 255.255.255.0 Gateway 192.168.10.1 Base Port HTTP Port 2222 User Manual VS-547-3GSDI – V1.0 Page 12 of 74 3/2016... -
Page 13: Remote Configuration
4. Remote Configuration 4.1 System Configuration Remote Setting is available by using web browser. Enter IP Address of the Camera and a Live View screen appears (see below). Press the Setup button located in the upper right area of the monitoring screen for Server Setup. For Remote Setting, the user should have manager-level authority or higher. - Page 14 Encoding Resolution is different from Input Resolution. Without Scaling, the input video will be cut according to the encoding resolution. If Scaling is selected, the input video will be adjusted according to encoding resolution. User Manual VS-547-3GSDI – V1.0 Page 14 of 74 3/2016...
- Page 15 This profile includes all the features that are supported in the constrained baseline profile, plus three additional features that can be used for loss robustness. User Manual VS-547-3GSDI – V1.0 Page 15 of 74 3/2016...
- Page 16 Select H.264 or MJPEG for the Secondary, Tertiary or Quartic Streaming. With H.264, Bitrate Mode or Quality Mode can be selected for the Preference. MJPEG supports the Quality Mode only. User Manual VS-547-3GSDI – V1.0 Page 16 of 74 3/2016...
- Page 17 Select the Audio Operation Mode: Mode Action No Operation Tx-Only Transmit Only Rx-Only Receive Only Tx & Rx Transmit and Receive Input Gain Audio Input Gain ranges from 0 to 31. User Manual VS-547-3GSDI – V1.0 Page 17 of 74 3/2016...
- Page 18 Audio Audio Output: The input audio is transmitted to the encoder. Loopback: Does not transmit the audio to the encoder. Audio input and output to the camera. User Manual VS-547-3GSDI – V1.0 Page 18 of 74 3/2016...
-
Page 19: Image Configuration
4. Remote Configuration 4.3 Image Configuration User Manual VS-547-3GSDI – V1.0 Page 19 of 74 3/2016... - Page 20 Gain when subject is dark and controlled by the Iris when subject is bright. As both Gain and Iris are fixed, this mode is used when exposing at a fixed camera sensitivity. User Manual VS-547-3GSDI – V1.0 Page 20 of 74 3/2016...
- Page 21 Defog Mode When the surrounding area of the subject is foggy and low contrast, the defog mode will make the subject appear clearer. User Manual VS-547-3GSDI – V1.0 Page 21 of 74 3/2016...
- Page 22 Controls video input brightness by selecting values between 0 and 255. Contrast Controls video input contrast by selecting values between 0 and 255. Saturation Controls video input saturation by selecting values between 0 and 255. User Manual VS-547-3GSDI – V1.0 Page 22 of 74 3/2016...
- Page 23 User can adjust Edge Enhancement Strength from 0 to 31 (with 31 being the highest strength level). Schedule To allow different camera configurations according to time of a day, the scheduling feature of the camera allows user to define these configurations. User Manual VS-547-3GSDI – V1.0 Page 23 of 74 3/2016...
- Page 24 1. Position camera and select a mask from the drop down menu. 2. Press the “New” button to get a new mask and adjust mask size. 3. The specified mark can be shown by selecting the “Search” button. User Manual VS-547-3GSDI – V1.0 Page 24 of 74 3/2016...
-
Page 25: Network Configuration
Selection Description Local IP Fixed IP Address Fixed IP Local Gateway Gateway IP Address Local Subnet Subnet Mask DHCP Contact your ISP provider or network manager for IP address information. User Manual VS-547-3GSDI – V1.0 Page 25 of 74 3/2016... - Page 26 Decoder, VMS or NVR software is connected in the Multicast Mode. The Multicast IP Address selection range is between 224.0.0.0 and 239.255.255.255. The selection can be used only when the media protocol is set to Multicast. User Manual VS-547-3GSDI – V1.0 Page 26 of 74 3/2016...
- Page 27 When Zeroconf is ON, it allows the discovery of the client according to Zeroconf Protocol. WS Discovery Discovery function based on web service is enabled. It allows the discovery by the client SW which is supporting Onvif. User Manual VS-547-3GSDI – V1.0 Page 27 of 74 3/2016...
- Page 28 User Name: Enter the user name that will be used as a session name in the SDP file. File Name: Enter the file name that will be used as the name of the SDP file. When this is entered, it can be accessed through http://ServerAddress/filename User Manual VS-547-3GSDI – V1.0 Page 28 of 74 3/2016...
- Page 29 Destination Port: Set the Port of the Destination System which will receive MPEG-TS stream. SNMP SNMP (Simple Network Management Protocol) is compatible with both SNMPv1 and SNMPvec. Settings for using SNMP are as follows: User Manual VS-547-3GSDI – V1.0 Page 29 of 74 3/2016...
- Page 30 Internet Protocol Suite, to notify a domain name server to change, in real time (ad-hoc) the active DNS configuration of its configured hostnames, addresses or other information stored in DNS. User Manual VS-547-3GSDI – V1.0 Page 30 of 74 3/2016...
- Page 31 IP in the network. IP Filtering IP Filtering is simply a mechanism that decides which types of IP datagrams will be processed normally and which will be discarded. User Manual VS-547-3GSDI – V1.0 Page 31 of 74 3/2016...
- Page 32 Email sending can be tested with this button. Please note that configured settings should be saved first by pressing the Apply button before using the Email Test Function. One of the following messages will appear as a result of the test: User Manual VS-547-3GSDI – V1.0 Page 32 of 74 3/2016...
- Page 33 The number of JPEG frames is configured appropriately. This setting is applicable only when JPEG Capture is selected. Capture Interval Select the interval of the captured frame. User Manual VS-547-3GSDI – V1.0 Page 33 of 74 3/2016...
- Page 34 %ADDR: address of the server (Domain name when DDNS is used; otherwise IP address) “.avi” or “.jpg” will be added automatically to the filename depending on the video file type. User Manual VS-547-3GSDI – V1.0 Page 34 of 74...
- Page 35 For Example: if the upload interval is 60 sec and the upload duration is 20 sec, a video clip for 20 sec is transmitted every 80 sec. User Manual VS-547-3GSDI – V1.0 Page 35 of 74 3/2016...
- Page 36 Primary, Secondary, Tertiary or Quartic video (H.264 only) can be selected. JPEG capture can be selected for uploading. Number of Frames Enter JPEG frame number (1-10). Capture Interval Select interval type of captured frames. User Manual VS-547-3GSDI – V1.0 Page 36 of 74 3/2016...
- Page 37 Enter User ID for VPN Client. Password Enter Password for VPN Client. VPN IP Address Set IP Address on VPN. VPN Port Set the Port on VPN. User Manual VS-547-3GSDI – V1.0 Page 37 of 74 3/2016...
- Page 38 4. Remote Configuration Connecting IP Addresses that are currently connected are listed here. User Manual VS-547-3GSDI – V1.0 Page 38 of 74 3/2016...
-
Page 39: Event Configuration
Configure the actions when the sensor is activated. Multiple actions can be set for a single event. On Video Loss Configure the actions when video input signal is lost. Multiple actions can be set for a single event. User Manual VS-547-3GSDI – V1.0 Page 39 of 74 3/2016... - Page 40 Multiple actions can be set for a single event. This event happens when the last client which has been receiving video from the IP Camera loses the connection. Motion Detection - Select the Use Motion Detection function User Manual VS-547-3GSDI – V1.0 Page 40 of 74 3/2016...
- Page 41 When silence is detected for a specific amount of time, an event is generated. - Sound Detection When sound is detected for a specific amount of time, an event is generated. User Manual VS-547-3GSDI – V1.0 Page 41 of 74 3/2016...
- Page 42 The function of the sensor port is set based on the type of the sensor connected. Sensor Schedule Choose Sensor OFF or Sensor ON and make a selection on the Sensor Schedule Table to schedule according to day of the week and time. User Manual VS-547-3GSDI – V1.0 Page 42 of 74 3/2016...
- Page 43 Set the duration of the Alarm or Beep Activation in case of an event. If Continuous is selected, the alarm will be in an active state until the operator resets it manually. User Manual VS-547-3GSDI – V1.0 Page 43 of 74...
- Page 44 50% or less. General The General setting configures the video analytics parameters which are applied to all functions: Line Crossing, Intrusion, and Tampering. User Manual VS-547-3GSDI – V1.0 Page 44 of 74 3/2016...
- Page 45 A Line Segment is drawn in the configuration. When enabled, objects which cross the line are detected and events are generated accordingly. Camera Height Configures the height of camera installation. This setting helps the internal operation of the object detection. User Manual VS-547-3GSDI – V1.0 Page 45 of 74 3/2016...
- Page 46 Defines the size of the object to be detected. Object size is defined by the percentage it covers in the total video size. Tampering When enabled, Camera Tampering, such as covering the lens with a towel, is detected and events are generated accordingly. User Manual VS-547-3GSDI – V1.0 Page 46 of 74 3/2016...
-
Page 47: Record Configuration
Data recorded in the disk can be uploaded to an FTP Server automatically for backup. FTP Server is configured on the Event page. This is valid only when Use Record is set to Use Disk. User Manual VS-547-3GSDI – V1.0 Page 47 of 74 3/2016... - Page 48 Specify the name of the directory to be created in the FTP Server. This is valid only when Use Record is set to Use FTP. Checking Status of Recording Recording Status can be checked on the main view page User Manual VS-547-3GSDI – V1.0 Page 48 of 74 3/2016...
- Page 49 VMS/NVR) etc. When there are multiple clients and only one is disconnected, the recording is not started. Event Type A recording is started when an Event is configured in the Event Type. User Manual VS-547-3GSDI – V1.0 Page 49 of 74 3/2016...
- Page 50 Once the disk initialization is finished, the disk status is shown on the Record page of the web-based setup. Refer to this chart for checking the disk status: User Manual VS-547-3GSDI – V1.0 Page 50 of 74 3/2016...
- Page 51 Recording, AVI files are created in a series and each size is limited to 10-2GB. Playback 1. After selecting an AVI file, a window will appear for opening or saving the file. User Manual VS-547-3GSDI – V1.0 Page 51 of 74 3/2016...
- Page 52 3. The Open button will download and automatically play with Windows Media Player. 4. The internet connection is disabled during downloading. Two AVI files cannot be download at the same time. User Manual VS-547-3GSDI – V1.0 Page 52 of 74 3/2016...
-
Page 53: Device Configuration
This information provides current serial communication status. Serial Setup Serial Protocol: This IP Camera supports one Serial Port: RS-232. Serial Port Configuration: The serial ports can be configured as follows: User Manual VS-547-3GSDI – V1.0 Page 53 of 74 3/2016... -
Page 54: Ptz Configuration
Camera or Receiver will be assigned with a unique ID. Enter the PTZ ID for control. The ID value range can be between 0 and 255. PTZ Port Select the Serial Port for PTZ Camera control. User Manual VS-547-3GSDI – V1.0 Page 54 of 74 3/2016... - Page 55 Preset Position by Event. Edit Label: Assign a Label to the Preset Position. Only the first 15 Preset Entries can have Assigned Labels (Preset-1 - Preset-15). User Manual VS-547-3GSDI – V1.0 Page 55 of 74 3/2016...
- Page 56 Preset, Pattern and Swing. The Option field is different for Preset and Pattern/Swing. For Preset, it configures the Preset Speed. For Pattern/Swing, it configures the number of repetitions. Dwell time between actions can be set up as well. User Manual VS-547-3GSDI – V1.0 Page 56 of 74 3/2016...
- Page 57 2. Select the Modify Group button. The following window will appear. 3. Set Action, Dwell Time and Option and click Enable. 4. Press Apply button and the Group can be used on the Live View Page. User Manual VS-547-3GSDI – V1.0 Page 57 of 74 3/2016...
- Page 58 Pattern, Swing or Group when a specified time expires after the PTZ control is stopped. Parking Time can be set from 0 to 3600 seconds and “0” means that the Auto Parking function is turned OFF. User Manual VS-547-3GSDI – V1.0 Page 58 of 74 3/2016...
- Page 59 Range # - ON: Regardless of Coordinate Value, user can see specific OSD. X - Coord: Position of Horizontal Coordinate. Y - Coord: Position of Vertical Coordinate. Font size: Select Font Size. Hue: Select Color. User Manual VS-547-3GSDI – V1.0 Page 59 of 74 3/2016...
-
Page 60: User Configuration
Live Viewing and PTZ Control Guest Live Viewing Only Add User Press Add button. The following window will appear. Enter User ID and password (Up to 15 characters) and select Privilege Level. User Manual VS-547-3GSDI – V1.0 Page 60 of 74 3/2016... - Page 61 Enter the current password and then set a new password. Modify Privilege Level Press Modify Privilege button to change User level. It is not allowed to change the privilege level of admin user. User Manual VS-547-3GSDI – V1.0 Page 61 of 74 3/2016...
- Page 62 Privilege Level After Login Skipped. Authentication HTTP authentication based on RFC 2617(HTTP Authentication: Basic and Digest Access Authentication) is supported User Manual VS-547-3GSDI – V1.0 Page 62 of 74 3/2016...
-
Page 63: System Configuration
Server, the MAC address is used in DDNS registration. Set Current Time Display Current Date and Time Current Domain In case the server is registered at DDNS Server, the registered domain name is displayed. User Manual VS-547-3GSDI – V1.0 Page 63 of 74 3/2016... - Page 64 Factory Reset All settings including user accounts and logs are cleared. Factory Reset Except Network Settings All settings except for current network settings are changed to the default values. User Manual VS-547-3GSDI – V1.0 Page 64 of 74 3/2016...
- Page 65 (Coordinated Universal Time). In casual use, GMT (Greenwich Mean Time) can be considered equivalent to UTC. Local time is UTC plus the current time zone offset for the considered location User Manual VS-547-3GSDI – V1.0 Page 65 of 74 3/2016...
- Page 66 System ID and/or IP Camera time can be display over the video window in Internet Explorer. Each item can be turn on or off separately, and position also can be configured. This information is displayed after the video is decompressed. User Manual VS-547-3GSDI – V1.0 Page 66 of 74 3/2016...
- Page 67 - User Defined OSD You can enter any text you like independent. X-Coordinate or Y-Coordinate For example, if you enter 500, 500 values, OSD is placed in center of images. User Manual VS-547-3GSDI – V1.0 Page 67 of 74 3/2016...
- Page 68 4. Remote Configuration Language - Language Select the Language to be used for Web-Based Configuration. User Manual VS-547-3GSDI – V1.0 Page 68 of 74 3/2016...
-
Page 69: Vs Manager
Once VS Manager installed, select IP Discovery, create servers. On main page go to Tools, Options and change to this path below. In the address window, after the word "Files" type a space then (x86). User Manual VS-547-3GSDI – V1.0 Page 69 of 74 3/2016... -
Page 70: Data Sheet
DHCP, DNS, Dynamic DNS, RTP, RTSP, SNMP Dual Power Options of 12V DC or PoE (802af) ONVIF, PSIA Compliant Models available for 3GSDI Output or HDMI Output ______________________________________________________________________ User Manual VS-547-3GSDI – V1.0 Page 70 of 74 3/2016... - Page 71 6. Data Sheet Specification Sheet User Manual VS-547-3GSDI – V1.0 Page 71 of 74 3/2016...
-
Page 72: Appendix
Relay Type Contact Rating : 1A 30VDC Switching Power : Max 30W 62.5VA Switching Voltage : Max 60VDC Alarm Signal Output Type NO/NC Contact Signals Connection to External Device User Manual VS-547-3GSDI – V1.0 Page 72 of 74 3/2016... - Page 73 Pin No. Pin Name Description RS422 RX- RS422 RX+ RS422 TX- or RS485 TRX- It is selectable by S/W Setup RS422 TX+ or RS485 TRX+ It is selectable by S/W Setup User Manual VS-547-3GSDI – V1.0 Page 73 of 74 3/2016...
- Page 74 Marshall Electronics, Inc. 1910 East Maple Ave. El Segundo, CA 90245 Tel: (800) 800-6608 / (310) 333-0606 Fax (310) 333-0688 www.LCDRacks.com sales@lcdracks.com User Manual VS-547-SGSDI – V1.0 Page 74 of 74 3/2016...