Related Manuals for Marshall Electronics VS-541-HDSDI
Summary of Contents for Marshall Electronics VS-541-HDSDI
- Page 1 Marshall Electronics VS‐541‐HDSDI / HDI 2.0 Megapixel IP Zoom Camera X20 Zoom CMOS User Manual ...
- Page 2 Product options and specifications can be changed without notice. The information in this manual is furnished for informational use only and should not be construed as a commitment by Marshall Electronics, Inc. Marshall Electronics, Inc. assumes no responsibility or liability for any errors or inaccuracies that may appear in this publication.
-
Page 3: Table Of Contents
TABLE OF CONTENTS __________________________________________________ 1 - Introduction ........................4 1.1 About this Manual ....................4 1.2 Features........................4 1.3 Product and Accessories ..................5 1.4 System Connections ....................8 2 - Installation........................9 3 - System Operation ......................10 3.1 Remote Video Monitoring..................10 3.2 Initialization of IP address .................. -
Page 4: Introduction
X20 Optical Zoom, X12 Digital Zoom True Day & Night (ICR) VS-541 = CVBS & IP VS-541-HDSDI = HDSDI & IP Video Highly Efficient Compression Algorithm, H.264 & MJPEG Support Resolutions: CIF (352x240) – Full HD (1920x1080) ... -
Page 5: Product And Accessories
1- Introduction ___________________________________________________________________________ Serial Data RS-485 Support Data Pass-Through Mode: Serial Data Communication between IP Camera and Decoder Sensor and Alarm Event Alarm Notification 1 Alarm Sensor Input and 1 Alarm Output Relay are available User Interface ... -
Page 6: Part Names And Functions
1- Introduction ___________________________________________________________________________ Part Names and Functions Rear View ① ② Connector Function 1. Ethernet/802.3af Ethernet Port/802.3af LED: Booting and System Check 2. RESET Button Initialization of Network Setting 3. AUDIO IN Audio Input 4. AUDIO OUT Audio Output 5. POWER IN DC 12V 6. -
Page 7: System Connections
1- Introduction ___________________________________________________________________________ 1.4 System Connections The IP Camera can be connected in one of two ways: 1) 1 to 1 connection where one camera is connected to one PC client or a decoder system, or 2) 1 to many connections where one system can be connected to several PCs and decoder systems (the video server can work as a video decoder which takes the data from a video server or IP camera, decodes and outputs analog video). - Page 8 1- Introduction ___________________________________________________________________________ Multicast Mode If the network supports multicasting, a large number of decoders can be used to receive video effectively from a camera using a single streaming of video and audio. However, Multicast Mode is possible only when the network environment supports multicast. Relay Center 2 (Decoder) Site...
-
Page 9: Installation
2- Installation ___________________________________________________________________________ 2.1 Connecting Network (LAN) Connect the Power Adaptor to IP Camera Connect Network Cable to Ethernet Port To display video through Composite Port, after connecting each port to a monitor, set preview option “ON” on the web-viewer page. 2.2 Connecting Audio Audio is Full-Duplex. -
Page 10: System Operation
3- System Operation __________________________________________________________________________ 3.1 Remote Video Monitoring There are two ways to monitor video when the center system and IP camera are connected. In order for a proper operation, an IP address must be set accordingly. Please refer to the VS Manager Manual enclosed with product for further details. Default ID : admin Default Password : 1234 Video Monitoring using Internet Explorer... - Page 11 3- System Operation __________________________________________________________________________ Video Select Select the Video Stream to be Viewed: Primary or Secondary This camera is capable of Dual Streaming (Select “Use Dual Encode” on Video Menu); primary streaming and secondary streaming. Video will be displayed according to the resolution set on video configuration.
- Page 12 3- System Operation __________________________________________________________________________ Alarm Output Operate the Alarm Device by Pressing the Number Icon This camera supports one alarm output. A number icon indicates the status of the alarm device. Snapshot Capture video images and store them as BMP or JPEG files. ...
-
Page 13: Initialization Of Ip Address
3- System Operation __________________________________________________________________________ 3.2 Initialization of IP Address If a System IP Address is lost, the system can be reset to the Default IP Address using the reset button on the back side of the system. 1. While in operation, press the system reset button for more than 5 seconds. 2. -
Page 14: Remote Configuration
4- Remote Configuration ___________________________________________________________________________ 4.1 Using The Web Browser Remote setting is available by using a web browser. Enter the IP address of the camera and a live view screen appears as shown below. Press the Setup button located in the upper right area of the monitoring screen to go to the server setup. For Remote Setting, the user needs to be authorized higher than a manager level user. -
Page 15: System Configuration
4- Remote Configuration ___________________________________________________________________________ 4.2 System Configuration User Manual VS-541 – V01.0 Page 15 of 52 2/7/12... - Page 16 4- Remote Configuration ___________________________________________________________________________ General System ID Enter System ID for the Camera Title The set System ID is displayed with video image on Web browser. The System ID is also transferred to remote software, such as VMS, and displayed on it. ...
- Page 17 4- Remote Configuration ___________________________________________________________________________ Time Start Time The most recent camera booting date and time is the Start Time. Current Time Set Current Date & Time Enter a new date and time and press Set Current Time button to update. ...
-
Page 18: Video Configuration
4- Remote Configuration ___________________________________________________________________________ 4.3 Video Configuration User Manual VS-541 – V01.0 Page 18 of 52 2/7/12... - Page 19 4- Remote Configuration ___________________________________________________________________________ Encode Enable Preview Select ON to enable the display video on the monitor that is connected to the composite or HD-SDI video port. Select the Output Format at the end of the video page. Note that when Enable Preview is ON, dual streaming is not available.
- Page 20 4- Remote Configuration ___________________________________________________________________________ I-Frame Interval Determine I-Frame Interval between 1 and 255. H.264 Profile Select H.264 Profile: High Profile or Baseline Profile The standard defines various sets of capabilities, which are referred to as profiles, targeting specific classes of applications. ...
- Page 21 4- Remote Configuration ___________________________________________________________________________ Sensitivity Sensitivity is the Condition to Trigger an Event of Motion Detection The value determines the sensitivity of the motion detection within a block; the smaller number, the more sensitive it becomes. It is selectable from 0 to 10. Information Display System ID and/or Server Time can be display over the video window in Internet Explorer.
- Page 22 4- Remote Configuration ___________________________________________________________________________ The following table describes the rule for BurnIn OSD display: Small Middle Large Resolution (8 x8) (16x16) (32x32) 352x480 / 352x240 / 352x576 / 352x288 720x480 / 720x240 / 720x576 / 720x288 / 640x480 / 800x600 1024 x 768 / 1280x720 / 1280 x 960 / 1280x1024 / 1440x900 / 1600x900 / 1680x1050 / 1920x1056 / 1920x1080 /...
-
Page 23: Audio Configuration
4- Remote Configuration ___________________________________________________________________________ 4.4 Audio Configuration Algorithm Algorithm Select the Audio Algorithm: G.711 or AAC G.711 and AAC from client to server direction are supported. Thus, bidirectional audio communication is supported. Bit Rate Select the Bit Rate between 64Kbps and 128kbps when AAC is selected The sampling rate is fixed to 8KHz and 32KHz for G.711 and AAC respectively. - Page 24 4- Remote Configuration ___________________________________________________________________________ Mode Select Audio Operation Mode: Mode Action No operation Tx-Only Transmit only Rx-Only Receive only Tx & Rx Transmit and Receive Input Gain Set Audio Input Gain from 0 to 31 Audio Output Configure the Audio Source to be Played on Audio Output Port ...
-
Page 25: Network Configuration
4- Remote Configuration ___________________________________________________________________________ 4.5 Network Configuration User Manual VS-541 – V01.0 Page 25 of 52 2/7/12... - Page 26 4- Remote Configuration ___________________________________________________________________________ Local IP Mode Select the IP Mode: Fixed IP or DHCP (Dynamic Host Configuration Protocol) Depending on the selected mode, further configuration items are as follows: IP Mode Selection Description Local IP Fixed IP Address Fixed IP Local Gateway Gateway IP Address...
- Page 27 4- Remote Configuration ___________________________________________________________________________ Domain Name System (DNS) is a database system that translates a computer's fully qualified domain name into an IP address. Networked computers use IP addresses to locate and connect to each other, but IP addresses can be difficult for people to remember. For Example: It’s much easier to remember the domain name www.amazon.com than it is to remember its corresponding IP address (207.171.166.48).
- Page 28 4- Remote Configuration ___________________________________________________________________________ Zeroconf By selecting ON, it allows Zeroconf Protocol on the client side discovery. WS Discovery The Discovery Function is based on Web Service being enabled. It allows SW Client discovery that supports ONVIF. Authentication ...
- Page 29 4- Remote Configuration ___________________________________________________________________________ MPEG-TS is a standard format for transmission and storage of audio, video, and data and is used in broadcast systems such as DVB and ATSC. Transport Stream is specified in MPEG-2 Part 1, Systems (formally known as ISO/IEC standard 13818-1 or ITU-T Rec.
- Page 30 4- Remote Configuration ___________________________________________________________________________ Multicast Multicast IP The Multicast Menu is used for configuring the Multicast IP Address to which media stream is delivered when a client, such as Decoder, VMS or NVR software, is connected in Multicast Mode. The Multicast IP Address selection range is between 224.0.0.0 and 239.255.255.255.
- Page 31 4- Remote Configuration ___________________________________________________________________________ Address Information Followed Network Information is Displayed (Read Only): IP Address: The Camera’s own IP Address. This information is useful when the Camera’s IP Mode is set to DHCP. Domain Name: If the Camera is registered to the DDNS Server, the Registered Domain Name is displayed.
-
Page 32: Serial Configuration
4- Remote Configuration ___________________________________________________________________________ 4.6 Serial Configuration Serial Port Configuration Serial Port Information This camera supports one RS-485 serial port. By default, Pelco-D protocol is used with 2400bps baud rate. Sensor Type There is one sensor input port on this Megapixel IP Camera. The sensor port can be configured to the following: User Manual VS-541 –... - Page 33 4- Remote Configuration ___________________________________________________________________________ Function Operation Not used The port is normally open and NO (Normally Open) activated when closed. The port is normally closed and NC (Normally Closed) activated when opened. The function of the sensor port is set based on the type of the sensor connected. Sensor Schedule ...
-
Page 34: Event Configuration
4- Remote Configuration ___________________________________________________________________________ 4.7 Event Configuration User Manual VS-541 – V01.0 Page 34 of 52 2/7/12... - Page 35 4- Remote Configuration ___________________________________________________________________________ When a Decoder is connected to an IP Camera instead of a PC Client, one system becomes a Local System and the other a Remote System (generally the system being used by the user is called the Local System). Actions can be configured for Remote System Events as well as Local System Events.
- Page 36 4- Remote Configuration ___________________________________________________________________________ Port Specify a Port for SMTP Operation (Port 25 is the Default Port in SMTP Operation. If a different port is configured in the SMTP Server, this port needs to be changed accordingly). Sender Address Enter an Account Registered in the SMTP Server.
- Page 37 4- Remote Configuration ___________________________________________________________________________ Message Description Email Sent Test Email has been sent successfully. Client Successfully reception can be checked. Connection to the SMTP Server failed. It is Failed to Connect to necessary to check if the server is reachable and SMTP Server server address and port are correct.
- Page 38 4- Remote Configuration ___________________________________________________________________________ “.avi” or “.jpg” will be added automatically at the end of the filename depending on the type of Video File. FTP Base Directory Specify the name of the directory to be created on the FTP Server. It is valid only when Use Record is set to Use FTP on Record Session.
-
Page 39: Preset Configuration
4- Remote Configuration ___________________________________________________________________________ 4.8 Preset Configuration Preset Select Preset # and insert the Preset Name. Set Camera Position for the Preset and press Save List button. User Manual VS-541 – V01.0 Page 39 of 52 2/7/12... -
Page 40: Record Configuration
4- Remote Configuration ___________________________________________________________________________ 4.9 Record Configuration User Manual VS-541 – V01.0 Page 40 of 52 2/7/12... - Page 41 4- Remote Configuration ___________________________________________________________________________ DISK SD Memory can be used and at least 1GB size is recommended. A disk with either an EXT3 or FAT32 File System can be read in Linux PC. However, only a disk with a FAT32 File System can be read in Windows PC. Less than 4Mbps of Video Bit Rate is recommended when you record and monitor video simultaneously since frame dropping may happen due to performance limitation.
- Page 42 4- Remote Configuration ___________________________________________________________________________ General Use Record - OFF: Recording function will not be used when ‘OFF’ is selected. - Use Disk: Recording will be enabled and data will be written to a disk. - Use FTP: Recording will be enabled and data will be uploaded to an FTP Server. In this mode FTP upload by event is automatically disabled.
- Page 43 4- Remote Configuration ___________________________________________________________________________ Event Type Three recording modes are supported: Continuous, Event, Disconnect. In case of event recording, event types can be selected among several events. Selected event type is used for configuring the schedule table. Up to 4 event types can be configured and each event type can be a combination of sensor, video loss and motion event.
- Page 44 4- Remote Configuration ___________________________________________________________________________ Press Search Page button on the Record Setup page. All Recorded Data from a specified date will be displayed on this page. To begin, choose Date of the Search and an AVI File list will be shown. The File Name will contain the Date and Time: “Date Begin Time End Time.avi”.
- Page 45 4- Remote Configuration ___________________________________________________________________________ The Web Connection is disabled during downloading. Also, two AVI Files can not be downloaded at the same time. Data Deletion If you want to delete recorded files, select the files by checking the item box in front of each file and click the Delete button.
-
Page 46: User Configuration
4- Remote Configuration ___________________________________________________________________________ 4.10 User Configuration User List Users can be registered and user privilege levels can be specified. User configuration can be edited and saved by Admin User only. Maximum of 16 users can be registered and each user can have one of four privileges: Privilege Allowed Operations Remarks... - Page 47 4- Remote Configuration ___________________________________________________________________________ Delete User Select the User to be deleted and click the Delete button to remove. Change Password Click the Modify Password button to change the current password. Enter the current password and then set a new password. ...
-
Page 48: Camera Configuration
4- Remote Configuration ___________________________________________________________________________ 4.11 Camera Configuration User Manual VS-541 – V01.0 Page 48 of 52 2/7/12... - Page 49 4- Remote Configuration ___________________________________________________________________________ Auto Exposure AE Mode Refer to the AE Mode Table for Auto Exposure Options: Program AE Mode / IR Remove Function Program AE O [manual] O [on/off] Program AER1 O [auto] : O [on/off] [IR Remove – 1] Hi Sensitivity Program AER2 O [auto] :...
- Page 50 4- Remote Configuration ___________________________________________________________________________ White Balance Mode Lighting Note Daylight, Auto Normal Fluorescent Light Default (2800k~8000k) Set WB Red & Blue Manual Not specified Offset Manually Sodium Vapor Auto Sodium Light Mercury Vapor Auto Mercury Light Auto Focus AF OnePush Mode Set Manual Focus Automatically with this function.
- Page 51 4- Remote Configuration ___________________________________________________________________________ Aperture Level Aperture Level ranges from 0 to 15. Aperture Control is a function which adjusts the enhancement of the edges of objects in the picture. There are 16 levels of adjustment, beginning with “no enhancement.” When shooting text, this control may help by making the text sharper.
-
Page 52: Vs Manager
Diagnostic Function: PING, Network Bandwidth Measurement, Video/Audio Output, Port Check, Serial Port Check. Firmware Upgrade. Marshall Electronics, Inc. 1910 East Maple Ave. El Segundo, CA 90245 Tel: (800) 800-6608 / (310) 333-0606 Fax (310) 333-0688 www.LCDRacks.com sales@lcdracks.com User Manual VS-541 –...