Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Ironton 46182
Summary of Contents for Ironton 46182
- Page 1 1 / 2 I N . S P A D E H A N D L E D R I L L OWNER’S MANUAL WARNING: Read carefully and understand all ASSEMBLY AND OPERATION INSTRUCTIONS before operating. Failure to follow the safety rules and other basic safety precautions may result in serious personal injury. Item# 46182...
-
Page 2: Intended Use
Thank you very much for choosing an IRONTON product! For future reference, please complete the owner’s record below: Model: _______________ Purchase Date: _______________ Save the receipt, warranty and these instructions. It is important that you read the entire manual to become familiar with this product before you begin using it. -
Page 3: Electrical Safety
• Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases, or dust. Power tools create sparks which may ignite the dust or fumes. • Keep bystanders, children, and visitors away while operating a power tool. Distractions can cause you to lose control. - Page 4 • Remove any adjusting keys or wrenches before turning the power tool on. A wrench or key that is left attached to a rotating part of the tool may result in personal injury. • Do not overreach. Maintain proper footing and balance at all times. Loss of balance can cause an injury in an unexpected situation.
-
Page 5: Extension Cords
• Feed the work piece in the correct direction and speed. Feed the work piece into a blade, cutter, or abrasive surface against the direction of the cutting tool’s direction of rotation only. Incorrectly feeding the work piece in the same direction may cause the work piece to be thrown out at high speed. - Page 6 Guidelines for Using Extension Cords • If you are using an extension cord outdoors, be sure it is marked with the suffix “W-A” (“W” in Canada) to indicate that it is acceptable for outdoor use. • Be sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified person before using it.
- Page 7 Always check that the material being drilled is secure and clamped in place if • necessary to prevent any movement. An unstable work piece can cause the drill bit to bind, causing of control and injury. Never hold the work piece in your hand, lap or against other parts of the body when •...
-
Page 8: Unpacking And Contents
FIG 1 KNOWING YOUR DRILL (FIG 1) 1. Chuck 4. Auxiliary Handle 2. Power-on Indicator 5. Rear Handle 3. Rocker Switch UNPACKING AND CONTENTS IMPORTANT: Due to modern mass production techniques, it is unlikely the tool is faulty or that a part is missing. If you find anything wrong, do not operate the tool until the parts have been replaced or the fault has been rectified. -
Page 9: Auxiliary Handle
AUXILIARY HANDLE The auxiliary handle can be attached to the electric drill in three different positions: Left, Top and Right. 1. Install the auxiliary handle by rotating it clockwise into one of the mounting holes. 2. To remove the auxiliary handle, rotate the handle counterclockwise. REAR HANDLE The Rear Handle can be attached to the rear end of the drill in 2 positions, Horizontal and Vertical. - Page 10 To install a drill bit: Inspect the drill bit shank and the drill’s chuck jaws for dirt or foreign matter and clean if necessary. Dirt on the drill bit shank or on the chuck jaws can cause misalignment or bit slippage during use. Drill bits larger than the drill’s maximum rated capacity may cause the motor to overload and/or gear damage.
-
Page 11: Drilling In Metal
With the tool unplugged from its power source • Install the appropriate bit into the chuck and tighten the chuck. • Place the forward/reverse switch in the forward position. • Mark the location(s) on the work piece where the holes are to be drilled. •... - Page 12 MAINTENANCE CLEANING Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to damage from various types of commercial solvents and may be damaged by their use. Use clean clothes to remove dirt, dust, oil, grease, etc. WARNING: Do not at any time let brake fluids, gasoline, petroleum-based products, penetrating oils, etc., come in contact with plastic parts.
- Page 13 DIAGRAM AND PARTS LIST Page of 15...
-
Page 14: Parts List
Parts List Part Description Part # Description Screw M5*22 Baffle ring Chuck 13mm1/2"-20UNF 607 bearing sleeve Output spindle Bearing 608-2z Key 3*3.7*10 Armature (120v) Circlip for flange 35 Bearing 609-2z Dust ring Gear box Felt seal Needle bearing hk0709 Bearing 6003 Middle spindle gear Screw st4.8*50 Small gear... -
Page 15: Two Year Warranty
TWO-YEAR WARRANTY This product is warranted free from defects in material and workmanship for 2 years after date of purchase. This limited warranty does not cover normal wear and tear or damage from neglect or accident. The original purchaser is covered by this warranty and it is not transferable. Prior to returning your tool to store location of purchase, please call our Toll-Free Help Line for possible solutions.
Need help?
Do you have a question about the 46182 and is the answer not in the manual?
Questions and answers