Care And Cleaning; Environmental Concerns - Electrolux CHI643BA User And Installation Manual

Table of Contents

Advertisement

care and cleaning

Clean the appliance after each use. Always use cookware
with clean bottom.
warning
WARNING
Sharp objects and abrasive cleaning agents can cause
damage to the appliance. For your safety, do not clean the
appliance with steam cleaners or high-pressure cleaners.
tips & information
TIPS & INFORMATION
Scratches or dark stains on the glass ceramic cause no effect
on how the appliance operates.
How to resolve problems with your cooktop
Problem
Possible cause and remedy
• Activate the appliance again and set the heat setting in 10 seconds.
You can't activate the cooktop or operate it.
• You touched 2 or more sensor fields at the same time. Only touch one sensor field.
• There is water or fat stains on the control panel. Clean the control panel.
-
The cooktop deactivates.
An object has been placed on the
The cooking zone is not hot because it operated only for a short time. If the cooking zone is hot, contact
The residual heat indicator does not come on.
our Customer Care team.
The cookware is too large or you put it too near to the controls. Put large cookware on the rear cooking
The sensor fields become hot.
zones if it is necessary.
The Automatic Switch Off is in operation. Deactivate the appliance and activate it again.
comes on
• No cookware on the cooking zone. Put cookware on the cooking zone.
-
-
• Not correct cookware. Use the correct cookware.
comes on
• The diameter of the bottom of the cookware is too small for the cooking zone. Move cookware to a
smaller cooking zone.
There is an error in the appliance. Disconnect the appliance from the electrical supply for some time.
Disconnect the fuse from the electrical system of the house. Connect again. If
and number comes on
contact our Customer Care team.
The Automatic Switch Off operatres when the cookware on the appliance boils dry. Deactivate the
appliance. Remove the hot cookware. After approximately 30 seconds, activate the cooking zone
again.
comes on
cookware and appliance has sufficiently cooled down. Refer to the Cookware section for correct
cooking temperatures.
Red rings, limescale or water rings, shiny
Cooktop surface has not been cleaned correctly. Cleaning/maintenance of the cooktop surface
metallic or other discolouration, scratches/
is not covered under warranty. If a service call is placed to clean the cooktop you will be
shadows, bubbles or other miscellaneous marks
charged for the visit. Use a ceramic glass cleaner such as Cerapol.
or stains on ceramic glass cooktop surface.
Spills of liquid with high sugar content. These types of spills must be removed immediately with a
Pitting of ceramic glass surface.
special scraper for the glass. If not permanent damage to the cooktop glass can occur which is
not covered under warranty.
-
The heat setting changes between two levels.
The power management is activated. Refer to 'Power management'
The Child Safety Lock device or the Lock function operates. Refer to chapter 'Operating instructions' .
comes on
If you tried the above solutions and cannot repair the problem,
speak to your dealer or our Customer Care team. Give
the data from the rating plate, three digit letter code for the
ceramic glass (it is in the corner of the glass surface) and an
error message that comes on. Make sure, you operated the
10 CARE AND CLEANING Induction Cooktops
To remove the dirt:
1. • Remove immediately: melted plastic, plastic foil, and
food with sugar. If not, the dirt can cause damage to
the appliance. Use a special scraper for the glass. Put
the scraper on the glass surface at an acute angle and
move the blade on the surface.
• Remove after the appliance is sufficiently cool:
limescale rings, water rings, fat stains, shiny metallic
discolourations. Use a special cleaning agent for glass
ceramic or stainless steel.
2. Clean the appliance with a moist cloth and some detergent.
3. At the end rub the appliance dry with a clean cloth.
button. Remove the object from the sensor field.
will disappear from the display but the residual heat indicator will be shown until the
appliance correctly. If not the servicing by a customer service
technician or dealer will not be free of charge, also during the
warranty period. The instructions about the customer service
and conditions of guarantee are in the guarantee booklet.

environmental concerns

PNC:
949163298
Model:
CHI643BA
The symbol
220 - 240 V AC
on the product or on its packaging indicates
S NO.:
50Hz
7.4 KW
that this product may not be treated as household waste.
Made in China By
Electrolux Home
Products Pty Ltd
(240)949163C298(21)xxxxxxxx(20)00
Instead it should be taken to the appropriate collection point
for the recycling of electrical and electronic equipment.
PNC:
949163299
Model:
CHI743BA
220 - 240 V AC
S NO.:
By ensuring this product is disposed of correctly, you will help
50Hz
7.4 KW
Made in China By
Electrolux Home
prevent potential negative consequences for the environment
Products Pty Ltd
(240)949163299(21)xxxxxxxx(20)00
and human health, which could otherwise be caused by
inappropriate waste handling of this product.
For more detailed information about recycling of this product,
please contact your local council, your household waste
disposal service or the shop where you purchased the product.
environmental tips
ENVIRONMENTAL TIPS
Packaging material
The packaging materials are friendly to the environment and
can be recycled. The plastic components are identified by
marking: >PE<,>PS<, etc. Discard the packaging materials as
household waste at the waste disposal.
-
comes on again,
Induction Cooktops ENVIRONMENTAL CONCERNS 11

Advertisement

Table of Contents
loading

This manual is also suitable for:

Chi743baShi643ba

Table of Contents