Front Half; Install Tongue; Install Cv Driveline; Attach Driveline To H-Frame - Woods TS1680 Operator's Manual

TS1680 Pull-Type Assembly (Continued)

FRONT HALF

(Figure 29)

Install Tongue

1. Place tongue (1) between mast plates.
2. Place washer (27) and sleeve (19) on cap screw
(26).
3. Place washer (27†) between mast plates and
tongue, insert cap screw (26) with washer (27†)
and sleeve (19) through mast plates, tongue and
washer (27†).
4. Secure with washer (27) and lock nut (28).
5. Attach front half of attitude rod (13) to lug on
tongue using clevis pin (18) and cotter pin (29).
6. Raise front of cutter and install parking jack (4) to
support tongue.
7. Attach safety tow chain (5) to tongue by wrapping
chain around diagonal brace and threading the
hook end back through the large link on opposite
end of chain.

Install CV Driveline

Install Driveline
1. Coat input shaft of gearbox with a light coating of
grease.
2. Attach slip clutch on driveline (7) to input shaft of
gearbox. Tighten cap screws (20) and lock nuts
(21).
1. Tongue
2. CV H-frame mounting base
3. H-Frame
4. Parking jack
5. Safety chain
6. Front 2/3 drive
7. Rear 1/3 drive
8. 3-Joint drive bearing housing
11. Shield
12. Clevis pin, 1/2 x 5-3/4
13. Attitude rod
14. 1/2 Schedule 40 x 3.56 pipe
15. Hose holder
16. Sleeve, 5/8 x 1 x 9/16
17. Cup washer
18. Clevis pin, 1 x 2-1/2
19. Sleeve, 1.02 x 1.38 x .62
20. 1/2 NC x 3 HHCS GR5
40 Assembly
(Figure 29)
3. Attach rear tether chain on driveline to clip on
plastic gearbox shield.
H-Frame
1. Attach H-frame mounting bracket (2) to cutter deck
with carriage bolts (34), washers (35) and lock nuts
(30). Attach front of bracket (2) to cutter frame with
washers (36), lock washers (32) and self-tapping
screws (37).
2. Place H-frame (3) over bracket and align holes.
3. Secure H-frame to bracket using cap screw (24),
two sleeves (16), two cup washers (17) and lock
nut (25).

Attach Driveline to H-Frame

NOTE: Select holes in H-frame that will allow driveline
to run level. Refer to Operation section for driveline
height. Final adjustment will be necessary when cutter
is attached to the tractor.
Place driveline carrier bearing (8) between H-frame (3)
and secure with clevis pin (12) and cotter pin (38).
Install CV Drive
1. Slide rear yoke of CV driveline (6) over shaft of
driveline (7) and align with notch on shaft.
2. Secure drives together using cap screw (22) and
lock nut (21).
Install Drive Shield & Hose Holder
1. Attach drive shield (11) to driveline carrier bearing
using two cap screws (33) and lock washers (32).
2. Attach hydraulic hose holder (15) to the top hole in
H-frame (3) with cap screw (23), spacer (14) and
lock nut (30).
21. 1/2 NC Lock nut
22. 1/2 NC x 2 HHCS GR5
23. 1/2 NC x 5-1/2 HHCS GR5
24. 5/8 NC x 6 HHCS GR5
25. 5/8 NC Lock nut
26. 1 NC x 9 HHCS GR5
27. 1" Standard flat washer
28. 1 NC Lock nut
29. 1/4 x 1-1/2 Cotter pin
30. 1/2 NC Flange lock nut
32. 3/8 Standard lock washer
33. 3/8 NC x 1 HHCS
34. 1/2 NC x 1-1/2 Carriage bolt GR5
35. 1/2 Flat washer
36. 3/8 Flat washer
37. 3/8 x 1-1/4 Self-tapping screw
38. 3/16 x 1 Cotter pin
+ As required
(Rev. 1/25/2008)
MAN0577 (6/29/2007)