Table of Contents
Advertisement
SPECIFICATIONS
CCD CAMERA
Parameter
Signal System
Effective Number of Cells (H × V)
CCD Gain
Total γ Characteristics
Scanning Frequency/Horizontal
Scanning Frequency/Vertical
Scanning
Video Out
Synchronization Method
External Synchronization Input
Allowable External Synchronized Frequency Deviation
(Adjust Horizontal Synchronized Frequency)
Jitter (Adjust Horizontal Synchronized Frequency)
OVER-LIGHT PROTECTION (OLP), AUTO GAIN CONTROL (AGC)
Parameter
Detection Method
Control Method
Operation
AGC Operation
Indication
Operation
OLP Operation
Indication
Delay Time for protection circuit to
function after the event of over-light
AGC (Auto Gain Control) Monitor
Over-light Protection Reset Input
POWER SUPPLY AND ENVIRONMENTAL SPECIFICATIONS
Parameter
Power Supply
Power Consumption
Operating Ambient
Temperature
Condition
Humidity
Storage Temperature
C5909, -01, -02, -03, -10, -11, -12, -13
Weight
C5909-06, -07, -08, -09
Dimensional
C5909, -01, -02, -03, -10, -11, -12, -13
Outline
C5909-06, -07, -08, -09
Accessory
CONTROL METHOD
Parameter
Gain Control
(Image Intensifier)
Internal Synchronization Mode (INT Mode)
Shutter
External Pulse Control Mode (PULSE Mode)
Operation
Normal Mode
External Synchronization
by HD, VD
A
(
): CCIR signal system
Video monitors for use in Japan conform to EIA signal system.
15.734 ± 0.157 34
59.94 ± 0.5994
525 lines, 2: 1 interlace
Internal/External (Auto Selection by the Input Signal)
S, VS (SYNC Level: 0.3 V p-p), HV/VD (HD/VD level: 2 V to 5 V p-p) (Auto Selection by the Input Signal)
Detect the average value of video signals
Control the image intensifier gain
Change the image intensifier gain to maintain the output image of image intensifier brightness at a constant level
PROTECTION LED (red) flashes
Turn off the image intensifier
PROTECTION LED (red) light up continuously
500 ms Max.
TTL negative logic, AUX connector pin No. 4 (During AGC)
Input impedance: 1 kΩ, TTL positive Logic
Camera Head Rear Panel
5-pin AUX Connector
HD
VD
Imaging System
EIA
768 × 494
Adjust by the knob at the rear panel
1.0 (Switchable to 0.45)
1.0 V p-p, 75 Ω unbalanced
±1
±50
Description/Value
Description/Value
+12 (+10.5 to +15)
RH 70 or below (without moisture condensation)
66(W) × 71(H) × 216.8(D) (Excluding projection part)
66(W) × 68(H) × 216.8(D) (Excluding projection part)
Lens Mount Cap, Instruction Manual, Test and Inspection data
Manual (10-rotation vernier knob)
(Not adjustable when the protection circuit is in operation)
+5 V dc to +9 V dc
Internal frame signal (VD signal) synchronization
Shutter timing is controlled by the width of external pulses
Continuous operation (shutter open)
Pulse height: 2 to 4 V p-p
Input Impedance: 75 Ω
TTL: synchronization negative
Pulse width: 10 µs or over
Frequency: 15.73 kHz ±0.3 kHz (15.625 kHz ±0.3 kHz)
Pulse height: 2 V to 4 V p-p
Input Impedance: 75 Ω
TTL: synchronization negative
Pulse width: 200 µs or over
Frequency: 59.94 Hz ±1.2 Hz (50 Hz ±1 Hz)
CCIR
752 × 582
15.625 ± 0.156 25
50 ± 0.5
625 lines, 2: 1 interlace
4.4
0 to +40
-20 to +50
1040
1070
Description/Value
A
Unit
—
—
—
kHz
Hz
—
—
—
—
%
ns Max.
Unit
V dc
W Max.
°C
% RH
°C
g
g
mm
mm
—
A
3
Advertisement
Table of Contents
