Advertisement
Guide to Control Panel
a
Power light
Paper light
P
Turns the printer on/off.
Starts monochrome or color copy. Press both buttons simultaneously
to scan your original and save it as PDF on your PC.
o Special Operations
y
To perform print head cleaning, press y for 3 seconds until the power light is flashing. The
cleaning uses some ink from all cartridges, so run the cleaning only if quality declines like when
you see missing segments on your prints. To replace cartridge(s) that are not expended, open
the scanner unit and press y for 6 seconds until the print head moves. Then, follow the steps
from step E in the "Replacing Ink Cartridges" section.
For their special operations, see the copying section.
Replacing Ink Cartridges
A�
!
Never touch the ink cartridges while
the print head is moving.
Open.
D�
Q
Press y to check other expended
cartridges.
Press.
F�
G�
Remove only the yellow tape.
Pinch and remove.
I�
J�
Close.
Press. Charging ink is started.
b
c
Ink light
y
Stops copying or indicates an expended ink
cartridge.
y + P
While pressing y, turn on the printer to print the nozzle check
pattern shown below.
(a): OK.
(a)
(b): Needs a head cleaning.
(b)
, y
B�
C�
Press.
Check which cartridge is expended.
E�
Shake all new cartridge(s) and then unpack.
H�
Install the ink cartridges.
Press down until it clicks.
K�
Charging ink takes about 1.5 minutes. Wait until the light turns on.
Reading the Indication Lights
: flashing
The paper is jammed in the sheet feeder. Remove the jammed paper from the sheet feeder, load paper correctly, and press x r or r x.
No paper is loaded, or multiple sheets were fed at the same time. Load paper in the sheet feeder correctly and press x r or r x.
Ink cartridge(s) are running low on ink. Printing is still possible. Prepare new ink cartridge(s) or replace the cartridge(s). Only remove the
cartridge when you are ready to replace it. Ink cartridge(s) with a low ink level cannot be used even if they are reinserted into the printer. To
replace ink cartridge(s) that are running low, open the scanner unit and press y for 6 seconds until the print head moves. Next, follow the
steps from step C in "Replacing Ink Cartridges".
Ink cartridge(s) are expended, not installed correctly, or invalid. Install the ink cartridge(s) correctly or replace them. If an error still occurs,
remove and reinsert the cartridge.
Leave an expended cartridge installed until you have obtained a replacement. Otherwise the ink remaining in the print head nozzles may dry
out.
Fatal error. Turn the printer off and then back on. If this does not clear the error, turn the printer off and check inside the printer for jammed
paper or foreign objects. For instructions on how to remove jammed paper, see the troubleshooting section of the online User's Guide.
The printer's ink pads are nearing or at the end of their service life. Contact Epson Support to replace ink pads. When the printer's ink pads are
nearing the end of their service life, you can resume printing by pressing x r or r x. The paper light and the ink light flash alternately.
The firmware update has failed. You will need to re-attempt the firmware update. Ready a USB cable and visit your local Epson website for
further instructions.
Safety Instructions
Use only the power cord that
Place the printer near a wall
Use only the type of power
comes with the printer. Use of
outlet where the power cord
source indicated on the printer.
another cord may cause fire
can be easily unplugged.
or shock. Do not use the cord
with any other equipment.
Keep the printer away from
Do not open the scanner unit
Do not use aerosol products that contain
direct sunlight or strong light.
while copying, printing, or
flammable gases inside or around the printer.
scanning.
Doing so may cause fire.
Keep ink cartridges out of the
Do not shake the ink cartridges
If you remove an ink cartridge for later use,
reach of children.
too vigorously; otherwise ink
protect the ink supply area from dirt and dust
may leak from the cartridge.
and store it in the same environment as the
printer. Do not touch the ink supply port or
surrounding area.
Cartridge Codes
: on
Make sure the power cord
Do not let the power cord
meets all relevant local safety
become damaged or frayed.
standards.
Except as specifically explained in your
documentation, do not attempt to service the
printer yourself.
If ink gets on your skin, wash the area
thoroughly with soap and water. If ink gets into
your eyes, flush them immediately with water. If
discomfort or vision problems continue after a
thorough flushing, see a doctor immediately. If
ink gets into your mouth, spit it out immediately
and see a doctor right away.
200/200XL
Advertisement
