Download Print this page

Advertisement

SERVICE MANUAL
Ver 1.1 2004.09
US and foreign patents licensed from Dolby
Laboratories.
• SonicStage and SonicStage logo are trademarks or registered trademarks of Sony Corporation.
• MD Simple Burner, OpenMG, "MagicGate", "MagicGate Memory Stick", "Memory Stick", Hi-
MD, Net MD, ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony Corporation.
• Microsoft, Windows, Windows NT and Windows Media are trademarks or registered trademarks
of Microsoft Corporation in the United States and/or other countries.
• IBM and PC/AT are registered trademarks of International Business Machines Corporation.
• Macintosh is a trademark of Apple Computer, Inc. in the United States and/or other countries.
• Pentium is a trademark or registered trademark of Intel Corporation.
• All other trademarks and registered trademarks are trademarks or registered trademarks of their
respective holders.
Audio playing system
MiniDisc digital audio system
Laser diode properties
Material: GaAlAs
Wavelength: λ = 790 nm
Emission duration: continuous
Laser output: less than 44.6 µW
(This output is the value measured at a distance
of 200 mm from the lens surface on the optical
pick-up block with 7 mm aperture.)
Recording and playback time (Refer
to page 94 for details)
When using HMD1G (1GB disc):
Maximum 34 hours in Hi-LP stereo
When using MDW-80 in Hi-MD mode:
Maximum 10 hours and 10 min. in Hi-LP
stereo
When using MDW-80 in MD mode:
Maximum 160 min. in monaural
Maximum 320 min. in LP4 stereo
Revolutions
350 rpm to 3,600 rpm (CLV)
Error correction
Hi-MD:
LDC (Long Distance Code)/BIS (Burst
Indicator Subcode)
MD:
ACIRC (Advanced Cross Interleave Reed
Solomon Code)
Sampling frequency
44.1 kHz
Sampling rate converter
Input: 32 kHz/44.1 kHz/48 kHz
Coding
Hi-MD:
Linear PCM (44.1 kHz/16 bit) — PCM
ATRAC3plus (Adaptive TRansform
Acoustic Coding 3 plus)
Sony Corporation
9-879-075-02
Personal Audio Company
2004I05-1
Published by Sony Engineering Corporation
© 2004.09
For other Service and User Manuals, go to www.ManualDepot.com
Model Name Using Similar Mechanism
MD Mechanism Type
Optical Pick-up Name

SPECIFICATIONS

MD:
ATRAC
ATRAC3 — LP2/LP4
Modulation system
Hi-MD:
1-7RLL (Run Length Limited)/PRML
(Partial Response Maximum Likelihood)
MD:
EFM (Eight to Fourteen Modulation)
Frequency response
20 to 20,000 Hz ± 3 dB
Inputs
1)
MIC: stereo mini-jack
(minimum input level 0.13 mV)
Line in:
stereo mini-jack for analog input
(minimum input level 49 mV)
optical (digital) mini-jack for optical
(digital) input
Outputs
2)
i/LINE OUT
: stereo mini-jack (dedicated
emote control jack)/194 mV (10 kΩ)
Maximum output (DC)
2)
Headphones:
5 mW + 5 mW (16 Ω)
Power requirements
Sony AC Power Adaptor connected at the DC
IN 6V jack:
120 V AC, 60 Hz (Models for USA, Canada,
Mexico, and Taiwan)
240 V AC, 50 Hz (Model for Australia)
230 V AC, 50 Hz (Models for U.K. and
Hong Kong)
220 V AC, 50 Hz (Model for China)
100 - 240 V AC, 50/60 Hz (Other models)
PORTABLE MINIDISC RECORDER
MZ-NH1
US Model
AEP Model
UK Model
Australian Model
Chinese Model
Tourist Model
The recorder:
Lithium-ion rechargeable battery
LIP-4WM, 3.7 V, 370 mAh, Li-ion
Battery charging stand:
AC power adaptor DC 6V
Operating temperature
+5° C (+41° F) to +35° C (+95° F)
Battery life
4)
Hi-MD mode (When using a 1GB Hi-
MD disc)
(Unit: approx.hours)(JEITA
When
Linear
Hi-SP
PCM
Recording
6
8.5
continuously
Playing
10
15.5
continuously
Hi-MD mode (When using a 60/74/80-
minute standard disc)
(Unit: approx.hours)(JEITA)
When
Linear
Hi-SP
PCM
Recording
5
8
continuously
Playing
8
14.5
continuously
– Continued on next page –
E Model
NEW
MT-MZNH1-181
ABX-U
3)
)
Hi-LP
9.5
18
Hi-LP
9
17.5

Advertisement

   Related Manuals for Sony MZ-NH1

   Summary of Contents for Sony MZ-NH1

  • Page 1: Specifications

    • SonicStage and SonicStage logo are trademarks or registered trademarks of Sony Corporation. • MD Simple Burner, OpenMG, “MagicGate”, “MagicGate Memory Stick”, “Memory Stick”, Hi- MD, Net MD, ATRAC, ATRAC3, ATRAC3plus and their logos are trademarks of Sony Corporation. • Microsoft, Windows, Windows NT and Windows Media are trademarks or registered trademarks of Microsoft Corporation in the United States and/or other countries.

  • Page 2

    MZ-NH1 MD mode (Unit: approx.hours)(JEITA) When Stereo Stereo Stereo Recording 10.5 continuously Playing 14.5 18.5 continuously On power sources Use house current or rechargeable battery. For use in your house: For the supplied battery charging stand, use the AC power adaptor supplied with this recorder.

  • Page 3: Table Of Contents

    COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.

  • Page 4: Servicing Notes

    MZ-NH1 SECTION 1 SERVICING NOTES NOTES ON HANDLING THE OPTICAL PICK-UP Installing BLOCK OR BASE UNIT The laser diode in the optical pick-up block may suffer electrostatic Providing the required system environment break-down because of the potential difference generated by the charged electrostatic load, etc.

  • Page 5: General

    MZ-NH1 SECTION 2 This section is extracted from instruction manual. GENERAL Looking at controls The recorder F MENU button A x (stop) • CANCEL button B Display window G GROUP button C OPEN switch H T MARK button I X (pause) button...

  • Page 6

    MZ-NH1 The headphones/earphones with a remote control Using the clip for the remote control It may be hard for you to read the indications in the display if the remote control is attached upside down with the clip in its current position.

  • Page 7: Disassembly

    MZ-NH1 SECTION 3 DISASSEMBLY • This set can be disassembled in the order shown below. 3-1. DISASSEMBLY FLOW Note 1: The process described in can be performed in any order. Note 2: Without completing the process described in , the next process can not be performed.

  • Page 8: Main Board

    MZ-NH1 3-3. MAIN BOARD 4 two flexible boards (CN471, 701) 2 Remove two solders. q; MAIN board 3 flexible cable 4 flexible board 9 leaf spring (CN491) (EMC) (2) 8 toothed lock screw 5 three toothed lock (M1.4) screws (M1.4)

  • Page 9: Control Ornament Block

    MZ-NH1 3-5. CONTROL ORNAMENT BLOCK 4 two claws 7 flexible board (CN491) 4 claw 5 claw 8 control ornament block 2 battery case lid. 3 two screws (M1.4) L=2.5 1 Open the battery case lid. 3-6. MECHANISM DECK ASSY (MT-MZNH1-181)

  • Page 10: Gear (sa), Gear (sb)

    MZ-NH1 3-7. GEAR (BSA), GEAR (SB) 1 self tap screw 2 thrust retainer spring 3 washer (0.8-2.5) 4 gear (SA) 5 gear (SB) 3-8. OP SERVICE ASSY 1 Lead screw block assy is turned and it removes from OP service assy.

  • Page 11: Dc Ssm18d/c-np Motor (spindle) (m701), Dc Ssm21a/c-np Motor (sled) (m702), Dc Motor Unit (over Write Head Up/down) (m703)

    MZ-NH1 3-9. DC SSM18D/C-NP MOTOR (SPINDLE) (M701), DC SSM21A/C-NP MOTOR (SLED) (M702), DC MOTOR UNIT (OVER WRITE HEAD UP/DOWN) (M703) 3 two screws (M1.4) 4 DC SSM21A/C-NP motor (sled) (M702) 2 Remove two solders of flexible board. 1 Remove four solders of flexible board.

  • Page 12: Test Mode

    MZ-NH1 SECTION 4 TEST MODE OUTLINE 2. OPERATION IN SETTING THE TEST MODE • When the test mode becomes active, first the Display Check A key having no particular description in the text, indicates a set mode is selected. key.

  • Page 13

    MZ-NH1 4. CONFIGURATION OF THE TEST MODE 5. MANUAL MODE This is mode to adjust or check the operation of the set by function. Flow of the test mode: Operation of The Manual Mode Display Check Mode 1. Enter the test mode (Display Check mode).

  • Page 14

    MZ-NH1 6. OVERALL ADJUSTMENT MODE 6-2. Error Message in The Overall Adjustment Mode 6-1. Operation of The Overall Adjustment Mode In the Overall Adjustment mode, if an error occurred, it displays as 1. Enter the test mode (Display Check mode).

  • Page 15

    MZ-NH1 Flow of Self-diagnosis Result Display mode operation: 8. KEY CHECK MODE This mode is used for key check. Operation of The Key Check Mode The first error 1. Enter the test mode (Display Check mode). 1 #### 2. Press the [GROUP] key to activate the Key Check mode where the LCD displays as shown below.

  • Page 16: Electrical Adjustment

    MZ-NH1 Ver 1.1 SECTION 5 ELECTRICAL ADJUSTMENTS 1. PRECAUTIONS FOR ADJUSTMENT 3-3. Setting The Temperature Correction Value 1. Adjustment must be done in the test mode only. After adjusting, Procedure: 1. In the test mode (Display Check mode), press the [VOL+] key release the test mode.

  • Page 17

    MZ-NH1 3-4-2. PwrAdj adjustments ItemNo. Display Specification value Measuring point Repeat the following procedures and adjust all contents of “table 3- 2211 211 VC1 ** 2.05V +0.02V CL8003 4-1. PwrAdj Specifications”. 2.25V ±0.01V 2212 212 VC1H N ** CL8003 2213 213 VC2 ** 1.20V +0.01V...

  • Page 18

    MZ-NH1 6. And [FF] key once again to select the item number 2251 and 3-4-3. VBsAdj adjustments Procedure: display “251 ChgChk **” on the LCD of remote commander. 1. In the “3-4-2. PwrAdj Adjustments” completed status, press 7. Press the key confirm that “ChgCOK”...

  • Page 19

    MZ-NH1 3-7-2. Other setting 3-7. Setting The Adjustment Values 1. In the test mode (Display Check mode), press the [VOL+] key 3-7-1. Hi-MD3 setting to enter the Manual mode. Preparation: 2. Press the [FF] key five time to select the item number 0113 1.

  • Page 20

    MZ-NH1 3-9. Resume Clear Procedure: 1. In the test mode (Display Check mode), press the [VOL+] key to enter the Manual mode. 2. Press the [VOL+] key once, press the [FF] key once, press the [VOL--] key once, press the [FF] key once, and press the [VOL+] key twice, press the [FF] key three times to select the item number 1933.

  • Page 21: Diagrams

    MZ-NH1 SECTION 6 DIAGRAMS 6-1. BLOCK DIAGRAM – MD SERVO Section – OVER WRITE HEAD DRIVE IC601 (1/2) HR601 (Page 23) OVER WRITE OVER 69 HBB HEAD DRIVE WRITE 78 HA Q601, 602 HEAD 70 HAB EFM_CLK LATCH M703 OUTA...

  • Page 22: Block Diagram -audio Section

    MZ-NH1 6-2. BLOCK DIAGRAM – AUDIO Section – SWITCHING DRIVER, MUTEON HEADPHONE AMP (Page 23) IC351 OUT_ BEEP 199 2 BEEP_IN BEEP2 DCLSOUTL DIN2 OUT2 J351 MUTING FROM IC801 (1/3) Q351 (MD SERVO SECTION) DCLSOUTR DIN1 OUT1 J301 LINE IN...

  • Page 23: Block Diagram -power Supply Section

    MZ-NH1 4-3. BLOCK DIAGRAM – POWER SUPPLY Section – (Page 22) SDO0 SCK0 SDO0 DATA (Page 21) CLK 63 SCK0 VRMC 6 REC KEY STRB (Page 22) XWK3 3 XRST2 XRST1 MUTEON (Page 22) MUTEON 45 RESET SIGNAL VSTB VCO2 VC01 +5.5V...

  • Page 24

    MZ-NH1 • Note For Printed Wiring Boards and Schematic Diagrams • Waveforms Note on Printed Wiring Board: Note on Schematic Diagram: IC701 1 (VI1), 2 (WI1), IC501 wh (CLK) (Servo on) IC801 <czz (OSCO) • X : parts extracted from the component side.

  • Page 25: Schematic Diagram -main Section (1/9)

    MZ-NH1 • See page 36 for IC Block Diagram. • See page 24 for Waveforms. 6-4. SCHEMATIC DIAGRAM – MAIN Section (1/9) – (1/9) XRST_MTR_DRV C716 XRST_MTR_DRV SLD_CON_W C714 R701 R703 SLD_CON_W SLD_CON_V SLD_CON_V SLD_CON_U SLD_CON_U L701 L702 SLD_PWM SLD_PWM...

  • Page 26: Schematic Diagram -main Section (2/9)

    MZ-NH1 • See page 36 for IC Block Diagrams. 6-5. SCHEMATIC DIAGRAM – MAIN Section (2/9) – (2/9) D601 MA2Z748001S0 XCS_REC_DRV C660 REG_DACVREFH REG_F SUSPEND SUSPEND USB_HOLD USB_HOLD C656 RECP RECP D609 C655 EFM_CLK D610 MA2Z748001S0 EFM_CLK VOLTAGE DETECT MA2Z748001S0...

  • Page 27: Schematic Diagram -main Section (3/9)

    MZ-NH1 • See page 36 for IC Block Diagram. • See page 24 for Waveforms. 6-6. SCHEMATIC DIAGRAM – MAIN Section (3/9) – (Page 25) (3/9) (Page 26) C553 C523 C530 C554 6.3V C524 R505 0.01 R526 C519 R510 L503 +3V REGULATOR 10µH...

  • Page 28: Schematic Diagram -main Section (4/9)

    MZ-NH1 • See page 36 for IC Block Diagram. 6-7. SCHEMATIC DIAGRAM – MAIN Section (4/9) – (Page 27) (Page 25) (4/9) (Page 29) (Page 33) (Page 26) MINUS_MON MINUS_MON VBUS_MON VBUS_MON VB_MON VB_MON CHG_PWM CHG_PWM CHG_CTL CHG_CTL CHG_OPR CHG_OPR...

  • Page 29: Schematic Diagram -main Section (5/9)

    MZ-NH1 • See page 36 for IC Block Diagrams. • See page 24 for Waveform. 6-8. SCHEMATIC DIAGRAM – MAIN Section (5/9) – (Page 26) (5/9) (Page 27) XRST1 L903 10µH RESET SIGNAL C914 GENERATOR C957 C954 IC903 6.3V XC61CN1702NR...

  • Page 30: Schematic Diagram -main Section (6/9)

    MZ-NH1 • See page 36 for IC Block Diagrams. • See page 24 for Waveforms. 6-9. SCHEMATIC DIAGRAM – MAIN Section (6/9) – (6/9) +2.1V REGULATOR R308 Q301 IC302 2SA2018TL SDO0 XC6219B212MR C327 SDO0 B+ SWITCH R304 SCK0 100k SCK0...

  • Page 31: Schematic Diagram -main Section (7/9)

    MZ-NH1 • See page 36 for IC Block Diagram. 6-10. SCHEMATIC DIAGRAM – MAIN Section (7/9) – (Page 26) (7/9) BP352 (Page 30) (Page 33) R361 R360 D_VREG0 D_VREG0 D_VCONT_PWM D_VCONT_PWM DCLSOUTR DCLSOUTR DCLSOUTL DCLSOUTL BEEP BEEP D_ENVG D_ENVG D_ENREG...

  • Page 32: Schematic Diagram -main Section (8/9)

    MZ-NH1 • See page 36 for IC Block Diagrams. • See page 24 for Waveform. 6-11. SCHEMATIC DIAGRAM – MAIN Section (8/9) – (Page 26) (8/9) C873 C877 C878 X872 32.768KHz CN471 REAL TIME REC_KEY CLOCK REC_KEY SET_KEY_1 SET_KEY_1 PAUSE...

  • Page 33: Schematic Diagram -main Section (9/9)

    MZ-NH1 • See page 24 for Waveform. • See page 42 for IC Pin Function Description. 6-12. SCHEMATIC DIAGRAM – MAIN Section (9/9) – (9/9) SDO0 SDO0 SCK0 SCK0 (Page 30) WK_DET R876 REG5_REG R846 CHG_LED C847 CHG_LED C851 (Page 32)

  • Page 34: Printed Wiring Board -main Section (1/2)

    MZ-NH1 6-13. PRINTED WIRING BOARD – MAIN Section (1/2) – : Uses unleaded solder. • Semiconductor Location Ref. No. Location MAIN BOARD (COMPONENT SIDE) D152 G-10 D252 F-10 D301 D352 G-10 S891 D401 S891-1 D602 (PROTECT DETECT) D604 D605 S891-2...

  • Page 35: Printed Wiring Board -main Section (2/2)

    MZ-NH1 6-14. PRINTED WIRING BOARD – MAIN Section (2/2) – : Uses unleaded solder. • Semiconductor Location LITHIUM-ION Ref. No. Location RECHARGEABLE BATTERY MAIN BOARD (CONDUCTOR SIDE) LIP-4WM (CHASSIS) D431 D451 R912 (US, E18, JE) D455 D456 S892 C575 D457...

  • Page 36

    MZ-NH1 • IC Block Diagrams IC301 AK5356VN-L IC401 MM1655LCBE 18 17 MICR 22 RESET BAT– 25 CONVERTER MVDD 23 RF1 26 TYPE2 CONTROL MVSS 24 IAMP_CAL 27 REGISTER CCLK INTERFACE CDTI MVCM VCOM AMP_SEL 28 IAMP_CTL MRF 26 MIC POWER + –...

  • Page 37

    MZ-NH1 IC501 SN761059ZQLR 42 41 35 34 33 32 31 30 29 SERIAL INTERFACE POWER CPGND VCC2 SUPPLY TEMP A+B+C+D VREF09 NPPO MALFA VCC2 AVCC2 AW+DW AWBPF TON PEAK S-MONITOR OFTRK OFTRK TON BOTM DWBPF ADIP OFTTH T-ON TON-C TWPP...

  • Page 38

    MZ-NH1 IC601 SC901585VAR2 CHARGE PUMP NC A12 56 LATCH EFM BOTTOM LVDT WAKE 55 XWKO PRE DRIVER HOLD OUT CONTROL HOLD VBUS 54 VBUS LOGIC EFM TOP RST OUT BUFFER PRE DRIVER 53 WAKEC PVBUS PVBUS VBUS 52 V33UO CRST...

  • Page 39

    MZ-NH1 IC701 SC901583EPR2 56 55 54 53 52 BIAS VC LOW 3PHASE 3PHASE VOLTAGE VI1 1 CONTROL CONTROL DETECTOR WI1 2 GNDW1 3 GNDW2 3PHASE 3PHASE WO1 4 PRE DRIVER PRE DRIVER VMVW1 5 VMVW2 VO1 6 GNDUV1 7 GNDUV2...

  • Page 40

    MZ-NH1 IC891 AK6514CN-L 15 VCC CS 1 14 HOLD STATUS REGISTER VREF GENERATOR INSTRUCTION SO 2 VPP SW DECODE 13 NC CONTROL & NC 3 CLOCK GENERATION WP 4 DECODER BUFFERS GND 5 EEPROM 128K bit R/W AMPS 16384 × 8 INSTRUCTION &...

  • Page 41

    MZ-NH1 IC901 SC901584EPR2 36 35 RESET 2 SERIAL RST2 PASS POWER STEP REGULATOR 3 SWITCH 2 UP-DOWN REGC2 DRIVER RST2 MUTING REG2G REF2 VREF SERIAL BUFFER REGO2 PASS REGULATOR 2 REGI2 32 DTC2 REGC1 VREF RST1 SERIAL REF2 REGO1 PASS...

  • Page 42

    MZ-NH1 • IC Pin Function Description IC801 CXD2681-222GG (SYSTEM CONTROLLER, DIGITAL SIGNAL PROCESSOR) Pin No. Pin Name Description DVDD1_0 — Power supply terminal DVSS1_0 — Ground terminal DVDD1_1 — Power supply terminal DVSS1_1 — Ground terminal DVDD1_2 — Power supply terminal DVSS1_2 —...

  • Page 43

    MZ-NH1 Pin No. Pin Name Description DAVDD — Power supply terminal (for D/A converter) DVDD25LPF — Power supply terminal (for D/A converter) DAVSS — Ground terminal (for D/A converter) OSCVDD — Power supply terminal (for 22 MHz OSC) USBOSCVDD —...

  • Page 44

    MZ-NH1 Pin No. Pin Name Description Phase comparison output terminal for the playback EFM system master PLL FILI Filter input terminal for the playback EFM system master PLL FILO Filter output terminal for the playback EFM system master PLL CLTV...

  • Page 45

    MZ-NH1 Pin No. Pin Name Description VREFL Reference voltage terminal connected to the capacitor (for the built-in D/A converter L-CH) AOUTL Built-in D/A converter L-CH signal output AOUTR Built-in D/A converter R-CH signal output VREFR Reference voltage terminal connected to the capacitor (for the built-in D/A converter R-CH)

  • Page 46

    MZ-NH1 Pin No. Pin Name Description A7CAL_SW A7 offset voltage CAL on/off control signal output terminal Serial data input from the EEPROM and real time clock IC Serial data output to the EEPROM, real time clock IC, A/D converter and power controller...

  • Page 47

    MZ-NH1 Pin No. Pin Name Description XRST_MTR Reset signal output to the motor driver _DRV XCS_NV Chip select signal output to the EEPROM CHG_PWM Charge current or voltage control signal output terminal IAMP_CAL Offset signal output of current sense amplifier —...

  • Page 48

    MZ-NH1 Pin No. Pin Name Description SCS4 Chip select signal output for ATRAC3 plus encoder communication Not used HI_Z_SLD Standby signal output terminal for the sled motor HI_Z_SPDL Standby signal output terminal for the spindle motor 291 to SET_CODE0 to...

  • Page 49: Exploded Views

    MZ-NH1 SECTION 7 EXPLODED VIEWS NOTE: • Items marked “*” are not stocked since they • -XX and -X mean standardized parts, so they The components identified by mark 0 or dotted line with mark 0 are may have some difference from the original are seldom required for routine service.

  • Page 50: Main Section

    MZ-NH1 7-2. MAIN SECTION mechanism deck section supplied MAIN board Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark 3-238-876-07 SCREW (M1.4), TOOTHED LOCK 2-190-061-01 SPACER (MIC-LINE) X-2023-571-1 MAIN BOARD, COMPLETE (for SERVICE) 2-178-887-01 SPACER (HEAD FLEXIBLE)

  • Page 51: Mechanism Deck Section

    MZ-NH1 7-3. MECHANISM DECK SECTION not supplied (including HR601 (over write head) ) not supplied HR601 (over write head) M702 M703 M701 The components identified by mark 0 or dotted line with mark 0 are critical for safety. Replace only with part number specified.

  • Page 52: Electrical Parts List

    MZ-NH1 SECTION 8 ELECTRICAL PARTS LIST MAIN NOTE: • Due to standardization, replacements in the • Items marked “*” are not stocked since they The components identified by mark 0 or dotted line with mark 0 are parts list may be different from the parts are seldom required for routine service.

  • Page 53

    MZ-NH1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C555 1-164-941-11 CERAMIC CHIP 0.0047uF 10% C401 1-125-777-11 CERAMIC CHIP 0.1uF C556 1-125-926-11 TANTALUM CHIP 4.7uF 6.3V C402 1-100-844-11 TANTALUM CHIP 22uF C557 1-125-777-11 CERAMIC CHIP 0.1uF...

  • Page 54

    MZ-NH1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C847 1-125-777-11 CERAMIC CHIP 0.1uF C650 1-100-442-11 TANTALUM CHIP 10uF 6.3V C849 1-125-777-11 CERAMIC CHIP 0.1uF C651 1-100-353-11 CERAMIC CHIP 4.7uF C851 1-125-777-11 CERAMIC CHIP 0.1uF...

  • Page 55

    MZ-NH1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark C951 1-100-841-11 TANTALUM CHIP 100uF 6.3V < FUSE > C952 1-100-841-11 TANTALUM CHIP 100uF 6.3V F351 1-576-439-41 FUSE (SMD) C954 1-125-777-11 CERAMIC CHIP 0.1uF C955 1-100-844-11 TANTALUM CHIP 22uF <...

  • Page 56

    MZ-NH1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark Q603 6-550-671-01 FET NTHC5513T1G < JACK > Q604 8-729-427-74 TRANSISTOR XP4601 Q605 6-550-671-01 FET NTHC5513T1G J301 1-815-950-12 JACK (LINE IN (OPT)) Q606 6-550-354-01 FET RTQ035P02TR J302...

  • Page 57

    MZ-NH1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R412 1-218-990-11 SHORT CHIP R413 1-220-804-11 RES-CHIP 2.2M 1/16W R622 1-244-161-11 RES-CHIP 1/16W R414 1-208-943-11 METAL CHIP 220K 0.5% 1/16W R623 1-244-161-11 RES-CHIP 1/16W R624 1-218-985-11 RES-CHIP...

  • Page 58

    MZ-NH1 MAIN Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark R821 1-220-804-11 RES-CHIP 2.2M 1/16W R822 1-218-989-11 RES-CHIP 1/16W R895 1-218-990-11 SHORT CHIP R823 1-218-965-11 RES-CHIP 1/16W R902 1-218-941-11 RES-CHIP 1/16W R903 1-218-989-11 RES-CHIP 1/16W R824 1-208-635-11 METAL CHIP 0.5%...

  • Page 59

    MZ-NH1 Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark MISCELLANEOUS 0 501 1-478-393-11 ADAPTOR, AC (AC-ES608K) (US, TW) 0 501 1-478-394-11 ADAPTOR, AC (AC-ES608K) (AEP, E18) ************** 0 501 1-478-395-11 ADAPTOR, AC (AC-ES608K) (UK, HK) 1-805-493-11 LCD MODULE...

  • Page 60: Revision History

    MZ-NH1 REVISION HISTORY Clicking the version allows you to jump to the revised page. Also, clicking the version at the upper right on the revised page allows you to jump to the next revised page. Ver. Date Description of Revision 2004.07...

Comments to this Manuals

Symbols: 0
Latest comments: