Subscribe to Our Youtube Channel
Related Manuals for Eyemax IP POWER C Series
Summary of Contents for Eyemax IP POWER C Series
- Page 1 User Manual Please read this instruction carefully for correct use of the product...
- Page 2 Before use this product Before operation, we strongly advise users to read this manual and keep it properly for using later. Please use the specified power supply to connect. Avoid from in correct operation, shock vibration, heavy pressing which can cause damage to product.
-
Page 3: Table Of Contents
IP CAMERA USER MANUAL Table of Contents Introduction ........................1 1.1 Summarization ......................1 1.2 Check Package Content ....................1 1.3 Overview ........................2 Installation ........................3 2.1 Install IP-CAM ......................3 2.2 Install CMS ....................... 4 IE Remote Access ......................3 3.1 LAN .......................... - Page 4 IP CAMERA USER MANUAL 5.5.2 Security Configuration ................... 25 5.5.3 Configure Backup & Restore ................. 26 5.5.4 Reboot Device ....................26 5.5.5 Upgrade ......................27 Q & A ..........................28 Specification ......................... 30...
-
Page 5: Introduction
Page 1 IP CAMERA USER MANUAL 1 Introduction 1.1 Summarization This IP-CAMERA (short for IP-CAM) is designed for high performance CCTV solutions. It adopts state of the art video processing chips. It utilizes most advanced technologies, such as video encoding and decoding technology, complies with the TCP/IP protocol, SoC, etc to ensure this system more stable and reliable. -
Page 6: Overview
Page 2 IP CAMERA USER MANUAL 1.3 Overview Fixed Ring Network Cable Mounting Base Power Cable Cable Connections N e tw ork Ca ble Internet N e tw ork Ca ble N e tw ork Ca ble... -
Page 7: Installation
Page 3 IP CAMERA USER MANUAL 2 Installation 2.1 Install IP-CAM Before you start, please make sure that the wall or ceiling is strong enough to withstand three times the weight of the camera and check whether the power supply is in conformity with your AC outlet. -
Page 8: Install Cms
Page 4 IP CAMERA USER MANUAL Lens Cover Zoom Focus 2.2 Install CMS Find CMS software from CD and then double click “Setup.exe” file to pop up installation wizard. Install the software according to the prompts in the wizard. After you complete the installation, you will see the CMS and IP-Tool icon on the desktop. -
Page 9: Ie Remote Access
Page 5 IP CAMERA USER MANUAL 3 IE Remote Access You may connect IP-Cam via LAN or WAN. Here only take IE browser (6.0) for example. The details are as follows: 3.1 LAN In LAN, there are two ways to access IP-Cam: 1. access through IP-Tool; 2. directly access through IE browser. -
Page 10: Directly Access Through Ie
Page 6 IP CAMERA USER MANUAL administrator and click “Modify” button to modify the setting. The default password of the administrator is “123456”. ④ Double click the IP address and then the system will pop up the IE browser to connect IP-CAM. -
Page 11: Wan
Page 7 IP CAMERA USER MANUAL Select “Property” and then select internet protocol according to the actual situation (for example: IPV4). Next, click “Property” button to set the network of the PC. ② Open the IE browser and input the default address of IP-CAM and confirm. The IE browser will download Active X control automatically. - Page 12 Page 8 IP CAMERA USER MANUAL ② Go to Config Network ConfigWired menu to modify the IP address. ③ Go to the router’s management interface through IE browser to forward the IP address and port of the camera in the “Virtual Server”. Port Setup IP Setup Router Setup...
-
Page 13: Remote Preview
Page 9 IP CAMERA USER MANUAL 4 Remote Preview 4.1 The Remote Preview Interface People icon Zoom in Start recording Fix size Zoom out Playback Actual size Full screen Snap When motion detection alarm is triggered, the people icon turns red. Right click to pop up a pull-down list as shown below: Stream: Three streams are optional. -
Page 14: Snap Pictures
Page 10 IP CAMERA USER MANUAL Play Next frame Zoom out Pause The previous file Full screen Stop The next file Path Forward Zoom in Volume 4.3 Snap Pictures Select the picture number, and then click “Snap” icon as shown below: Single Snap Snap multiple pictures Select the picture number from Frame pull down list box, such as 2, and check “Title”... - Page 15 Page 11 IP CAMERA USER MANUAL Multi-picture Snap...
-
Page 16: Remote Live Surveillance
Page 12 IP CAMERA USER MANUAL 5 Remote Live Surveillance Functions of remote configurations include: System Configuration, Video Configuration, Alarm Configuration, Network Configuration and Advanced Configuration. You should firstly select the menu on the left, and then set up the relative parameters. When one user configures parameters of a certain device, other users can not set up this device. -
Page 17: Video Configuration
Page 13 IP CAMERA USER MANUAL 2. Set time zone. 3. Enable DST mode as required. 4. Set time. You may set time manually or enable NTP. 5.2 Video Configuration Camera Configuration includes five submenus: Camera Configuration, Video Stream, OSD Config, Video Mask and ROI Config. -
Page 18: Video Stream
Page 14 IP CAMERA USER MANUAL 7. 2D denoise, 3D denoise, digital gain, analog gain and frequency are adjustable. 8.You may repair bad pixel. 9. Press the "Save" button to save the settings. Before distortion correction After distortion correction 5.2.2 Video Stream ... -
Page 19: Osd Configuration
Page 15 IP CAMERA USER MANUAL 5.2.3 OSD Configuration Go to “Video Config” “OSD Config” menu to display the interface as shown below. You may set time stamp, device name and custom OSD here. Drag the time stamp and custom OSD to set their position. -
Page 20: Roi Configuration
Page 16 IP CAMERA USER MANUAL 3. Click “Save” button to save the settings. 4. Return to the live to see the following picture. Clear the video mask: Go to video mask menu and then click “Clear” button to delete the current video mask area. 5.2.5 ROI Configuration To set up ROI 1. -
Page 21: Alarm Configuration
Page 17 IP CAMERA USER MANUAL 5.3 Alarm Configuration Alarm configuration includes three submenus: Motion Detection Area, Motion Detection Trigger and Motion Detection Schedule. 5.3.1 Motion Detection Area 1. Go to “Alarm configuration""Motion Detection Area" to see an interface as below. 2. -
Page 22: Motion Detection Schedule
Page 18 IP CAMERA USER MANUAL 4. Trigger FTP: Check “Uploading picture”. Then the triggered snap pictures will be sent into FTP server address. Please refer to FTP configuration chapter for more details. 5. Press the "Save" button to save the settings. 5.3.3 Motion Detection Schedule Go to “Alarm configuration"... -
Page 23: Network Configuration
Page 19 IP CAMERA USER MANUAL You could set alarm time for alarm in some time of special day, such as holiday. 1. Select a date at the "Date" pull down list, press "Add" button to add that date to the list box on the right side and then move the scroll bar to set the schedule of that day. -
Page 24: Server Configuration
Page 20 IP CAMERA USER MANUAL following IP address. You may choose one of options as required. 3. Use the following IP address: display the IP address, subnet mask, gateway and DNS of the device. 4. PPPOE: User needs to manual input the user name and password for dial-up internet. Firstly, log in IE clients and then enter user name and password of PPPoE, save the setting and exit. -
Page 25: Ddns Configuration
Page 21 IP CAMERA USER MANUAL 5.4.5 DDNS Configuration 1. Go to "Network Configuration""DDNS Configuration" tab as shown below. 2. Apply for a domain name. Take WWW. dvrdydns.com for example. in the IE address bar to visit its website. Then click “Registration” Input www.dvrdydns.com button to register as shown below. -
Page 26: Rtsp
Page 22 IP CAMERA USER MANUAL 3. Input the username, password and domain name you apply for in the DDNS configuration interface. 4. Click “Save” button to save the settings. 5.4.6 RTSP Go to “Network Configuration” “RTSP” interface as shown below. 1. -
Page 27: Ftp
Page 23 IP CAMERA USER MANUAL 1. From Email: sender’s e-mail address 2. User name and password: sender’s user name and password 3. Server address: SMTP name of sender 4. Select the secure connection type at the Secure Connection pull down list according to user’ actual needs 5. -
Page 28: Advanced Configuration
Page 24 IP CAMERA USER MANUAL Parameter Meaning Server name The name of the FTP server Server address The address of the FTP server The port number of the FTP server Port User name The user name of the FTP server The password of the FTP server Password Path... -
Page 29: Security Configuration
Page 25 IP CAMERA USER MANUAL Modify User 3. Input original password of this user in the “password” text box. 4. Input new password in the “New password” and “Confirmation” text box. 5. Input computer’s physical address which is used to access the server in the “User PC MAC” text box. -
Page 30: Configure Backup & Restore
Page 26 IP CAMERA USER MANUAL 5. Select the MAC address which needs to be deleted from the MAC address list box and click “delete” button to delete that MAC address. 6. Click "save" button to save the above setting. 5.5.3 Configure Backup &... -
Page 31: Upgrade
Page 27 IP CAMERA USER MANUAL 5.5.5 Upgrade Go to Advanced Configuration—Upgrade interface as shown below. 1. Click “Browse” button to select the save path of the upgrade file 2. Click “Upgrade server firmware” button to start upgrading the application program 3. - Page 32 Page 28 IP CAMERA USER MANUAL 6 Q & A Q: How to find my password if I forget it? A：Reset the device to the default factory settings Default IP: 192.168.226.201 User name: admin Password: 123456 Q：Fail to connect devices through IE browser, why? A: Network doesn’t connect well.
- Page 33 Page 29 IP CAMERA USER MANUAL ④ Then click OK to finish setup. b. Other plug-ins or anti-virus blocks ActiveX. Please uninstall or close them. Q：No sound can be heard, why? A：Audio input device is not connected. Please connect and try again. B: Audio function is not enabled at the corresponding channel.
-
Page 34: Specification
Page 30 IP CAMERA USER MANUAL 7 Specification Model 2 Megapixel IR Water-proof Bullet Network Camera Image Sensor 1/3“CMOS 1920 x 1080 Image Size Electronic Shutter 1/25s~1/100000s Auto Iris Fixed Iris Camera Min. Illumination 0 Lux (IR ON) Lens 6mm (2.8mm, 3.6mm, 8mm optional) Day-Night Switch ICR auto switch Digital WDR...
Need help?
Do you have a question about the IP POWER C Series and is the answer not in the manual?
Questions and answers