Specifications - Makita 5603r Instruction Manual

ENGLISH (Original instructions)
1-1. Lever
2-1. Clamping screw
3-1. Base plate
4-1. Top guide
4-2. Base
5-1. 60 ﾟ angle cuts
5-2. 45 ﾟ angle cuts
5-3. 30 ﾟ angle cuts
5-4. Straight cuts
5-5. Blade

SPECIFICATIONS

Model
Blade diameter
Max. cutting depth
No load speed (min
Overall length
Net weight
Safety class
• Due to our continuing program of research and development, the specifications herein are subject to change without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for performing lengthways and
crossways straight cuts and mitre cuts with angles in
wood while in firm contact with the workpiece. With
appropriate Makita genuine saw blades, other materials
can also be sawed.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated and can, therefore, also be used from
sockets without earth wire.
For model 5705R
For public low-voltage distribution systems of
between 220 V and 250 V.
Switching operations of electric apparatus cause voltage
fluctuations. The operation of this device under
unfavorable mains conditions can have adverse effects
to the operation of other equipment. With a mains
impedance equal or less than 0.37 Ohms it can be
presumed that there will be no negative effects. The
mains socket used for this device must be protected with
a fuse or protective circuit breaker having slow tripping
characteristics.
Explanation of general view
5-6. Base
5-7. Top guide
6-1. Setting protuberances
6-2. Hex socket head bolt (For adjusting
riving knife)
6-3. Setting protuberances
6-4. Cutting depth
7-1. Lock-off button
7-2. Switch trigger
8-1. Hex wrench
5603R
165 mm
at 90° 54 mm
at 45° 38 mm
-1
) 5,000
330 mm
4.9 kg
/II
ENE078-2
ENF002-2
ENF100-1
5703R 5705R
190 mm 190 mm
66 mm 66 mm
46 mm 46 mm
4,800 4,800
356 mm 356 mm
5.7 kg 5.7 kg
/II /II
Noise
The typical A-weighted noise level determined according
to EN60745:
Model 5603R
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Model 5143R
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Model 5703R, 5705R, 5903R
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Model 5103R
Sound pressure level (L
Sound power level (L
Uncertainty (K) : 3 dB(A)
Wear ear protection
3
8-2. Shaft lock
9-1. Hex socket head bolt
9-2. Outer flange
9-3. Saw blade
9-4. Inner flange
10-1. Vacuum cleaner
13-1. Limit mark
14-1. Screwdriver
14-2. Brush holder cap
5903R 5103R
235 mm 270 mm
85 mm 100 mm
64 mm 73 mm
4,500 3,800
400 mm 442 mm
7.2 kg 9.4 kg
/II /II
) : 91 dB(A)
pA
) : 102 dB(A)
WA
) : 88 dB(A)
pA
) : 99 dB(A)
WA
) : 92 dB(A)
pA
) : 103 dB(A)
WA
) : 87 dB(A)
pA
) : 98 dB(A)
WA
5143R
355 mm
130 mm
90 mm
2,700
607 mm
14.0 kg
/II
ENG905-1