Troubleshooting - Omron HV-F127 Instruction Manual

TENS-EN01-22[HV-F127]-2

Troubleshooting

Problem
The batteries are inserted in
The power
wrong direction.
cannot be
turned on.
The Pads are not attached to
The power
the skin.
turns off
Pads are removed from the skin.
too soon.
The power The batteries are worn out.
turns off The power turns off automatically
while using in 15 minutes.
the unit.
The Electrode Cord is broken.
The clear film on the adhesive
surface of the Pad is not peeled off.
The adhesive surface of Pad is dirty.
The Pad
does not
attach to the
You used the Pad immediately
skin.
after washing it.
The adhesive surface of Pad is
damaged.
You used the Pad while you
were perspiring.
The
You washed the Pad too long
adhesive
and too frequently.
surface of
You stored the Pad under high
Pad is sticky.
temperature, high humidity, and
direct sunshine.
The Pad is not attached close to
the skin.
The Pads are attached
overlapping each other.
Cannot
The Electrode Cord is not
feel the
connected correctly.
stimulation.
The intensity is adjusted too weak.
The batteries are worn out.
The adhesive surface of Pad
is damaged.
The treatment time is too long.
The skin
The Pad is not attached close to
turns red.
the skin.
The skin
The adhesive surface of Pad is
feels
dirty or dried.
irritating.
The adhesive surface of Pad is
damaged.
If the unit does not operate after taking the above-mentioned measures, contact the nearest OMRON dealer.
19
11/17/03 6:49 PM Page 20
Cause
⇒ Insert the batteries in correct direction.
⇒ If the Pads are not attached to the skin, the power
will turn off automatically.
⇒ If the Pads come off from the skin, the power
will turn off automatically.
⇒ Replace the batteries with new ones.
⇒ Turn off the Intensity Dial/Power Button.
Unless it is turned off, the batteries will wear out
slightly faster.
⇒ Replace the Electrode Cord.
⇒Peel off the clear film on the adhesive surface.
⇒Wash the adhesive surface softly with your fingertips
under slow running water for several seconds.
⇒Sufficiently dry it and leave the adhesive surface to
airdry.
⇒Pad is a consumable.
Replace the Pad with a new one.
⇒Leave the Pad in the refrigerator overnight.
⇒Attach the Pad close to the skin.
⇒Attach the Pads by not overlapping them.
⇒Connect the Electrode Cord correctly.
⇒Turn the Intensity Dial/Power Button.
⇒Replace the batteries with new ones.
⇒Pad is a consumable.
Replace the Pad with a new one.
⇒ Limit the treatment time to 10 to 15 minutes.
⇒ Attach the Pad close to the skin.
⇒ Wash the adhesive surface of Pad softly with your
fingertips for several seconds under slow
running water.
⇒ Pad is a consumable.
Replace the Pad with a new one.
Remedial Action
(Refer to page 7)
(Refer to page 7)
(Refer to page 7)
(Refer to page 7)
(Refer to page 12)
(Refer to page 20)
(Refer to page 7)
(Refer to page 17)
(Refer to page 17)
(Refer to page 20)
(Refer to page 17)
(Refer to page 7)
(Refer to page 7)
(Refer to page 7)
(Refer to page 12)
(Refer to page 7)
(Refer to page 20)
(Refer to page 12)
(Refer to page 7)
(Refer to page 17)